Question about Audio & Video Receivers

Open Question

I have a roland rd-250s with a dead g and a flat in the 2nd lowest octave. I have had filaments replaced and keypads adjusted in the past. The usual charge for this service is prohibative. I need to learn how to open the keyboard (keys, keypads, filaments, computer boards, encased above metal) so that I can adjust keys/keypads, repair/replace filaments.

Posted by on

  • communistcom Jul 16, 2008

    this is a digital piano, not a receiver. If you have someone waiting to teach me exactly how to open the actual key/hammer assembly and isolate the filament/chip/pad/key assembly;diagnose problem with g/a flat, repair or replace worn part as necessary and reinstall to restore to working condition then I would define my problem as solveable through you and upon receipt of some good faith effort to inform me that you do, in fact possess this solution in contrast to 'you might have some basic tips, for example, then I will consider actually paying your $10 fee if necessary. I appreciate your services, however, the point of seeking online help versus taking my equipment in person to a repairman is not to spend money I can scarcely afford. I understood your premium offer when I read your site and posted my problem. Had that option deemed valuable to me I would have taken it. Your prompt made me wonder about the validity of your forum versus your paid information, and titling my problem as a receiver is inaccurate entirely. I have and plan to use this device for quite a while so if any of you can impart this information to me please respond in some specific manner which relates to the issue. Thank you, I hope you smiled a little, and I really will appreciate the help.---cc


×

1 Suggested Answer

japacheco83
  • 15 Answers

SOURCE: adjusting harness in the lowest position

Before helping out i think you should read this first!

AAFES RECALL NO. 08-003
RELEASE DATE:
4 February 2008
SUBJECT: HAZARDOUS RECALL - Evenflo recalls Discovery Child Safety Seats for a potential restraint failure.
DISTRIBUTION: WORLDWIDE In cooperation with National Highway Traffic Safety Administration (NHTSA), Evenflo Baby Products Inc. of Vandalia, OH is voluntarily recalling Discovery Child Safety Seats listed below for a potential restraint failure.
Items: Discovery Child Safety Seats
Number of Units Involved: Approximately One million
Description: The Discovery car seat is designed with a convenience base that attaches to the vehicle's seat and allows the seat to be attached or removed from the vehicle without removing the base.
Hazard: Tests conducted by NHTSA and the Evenflo company has found that these car seats have the potential to separate from its base. Seats could fail to adequately protect children in a high impact side collision.
Models Recalled: 390, 391, 534 and 552 Production Dates: Between April 2005 and January 29, 2008
Sold at: Major retailers and Catalogs. AAFES sold Models 390 and 391 through retail stores and catalog.
Remedy: Evenflo is providing current owners of these models with a free supplemental dual-hook fastener that has proven that the seat remains attached to the base in the event of such collisions.
Instructions for Customers: Owners of the affected seats can contact Evenflo toll-free at 800-356-2229 between 8am and 5pm ET or visit their website at http://safety.evenflo.com/cs/sc/cssc_RD.phtml
Consumers with questions about this or any other safety recall campaign may call NHTSA’s toll-free Vehicle Safety Hotline 1-888-327-4236 (TTY: 800-424-9153); or go to http://www.safercar.gov.

If you still want to adjust the straps, here is a link in pdf format to guide you with your straps and/or harness:

http://www.carseat.org/samples/Sample_Summary.pdf

Posted on Mar 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Roland RD-300SX has no sound output unless foot pedal is depressed.


Make sure that the pedal is connected to 'DAMPER' and not 'CONTROL'.

Sep 22, 2011 | Audio & Video Receivers

1 Answer

I have an rd 7103. Just moved. Hooked up again and no sound. Reconnected every wire several times and no sound even through the headset. all functions on the remote work even the aux outlet ?????


Turn the volume control to something medium.

The errant switch, control or condition may change and you will suddenly release the amp's full power and possibly destroying your speakers. If a signal isn't audible at 1/2 volume it's probably not there.

Carefully examine the front panel for clues like a misplaced Mute or Tape Monitor control or Multichannel Analog Input selected.

There is a good chance that a common control may have developed a high-resistance or 'dead

Mar 21, 2011 | Sherwood RD-7103 Receiver

1 Answer

I need a replacement woofer for a Roland DS90-A 24 bit digital studio monitor. Serial # BT46344


If you want an exact replacement you will need to contact www.roland.com If you want to replace the speaker yourself you can contact www.martinsoundproducts.com (out of Cleveland Ohio USA). they stock many speakers in all sizes and prices, but they are a wholesale company so the prices are very low. I suggest you replace the woofer in both of your monitors though so your sound will be balanced. besides if one speaker has malfuntioned chances are the other will soon anyway.

Mar 20, 2011 | Audio & Video Receivers

1 Answer

My Sherwood RD-6105 shuts off if I turn it up past 28 or 29 db (which isn't very loud). I'm using it in Dolby Digital mode. It even happens when I use it with my components that are analog. This just...


It's acting as if a short or near-short exists on the amp outputs at medium levels.

Disconnect one of your speakers at a time and try it. Make sure your speaker wires are tight and not shorting to anything and all channels have 6-ohms or more load.

Jan 16, 2011 | Sherwood RD-6105 Receiver

1 Answer

Concerning my Sherwood RD-7500 6.1 Channels Receiver


That still doesn't make much sense. Please slow down and say what you mean with detail and accuracy. We're not mind readers. You are our eyes and ears.

Is the following true?

"Video 1" video output goes to the TV and works ok. Though it is irrelevant since you don't have a video problem. That you mention it at all is distracting. Do you feel it is important?

Tower speakers are the main or only speakers. Do they work ok for other sources?

So, to be clearer, you have a problem with a particular sound source (the game console) being less loud than usual. Is it unusable or drastically different in level than other sound sources?

Where and how is the game console connected for audio? Can you move it to another input?

Have you considered that the game console or its settings may be the reason volume is lower than usual?

Jan 19, 2010 | Sherwood RD-7500 Receiver

1 Answer

Hear sound but cant get any real volume even at full blast


I was playing around with my Sherwood RD 6513 and adjust the the output level to its maximum, amongst other settings. This limited my output on the amp to a maximum volume of 65 not 90+.. Anyway i pluged in the microphone and done another 'auto setup' of the volume levels and distances, and this allowed the volume to exceed 65 again!

Also if you have an external source such as a DVD player - i would assume you have already checked its output volume setting?

Nov 23, 2008 | Sherwood RD-6500 Receiver

1 Answer

Yamaha B5CR organ... 3 notes in each octave are not sounding


Open up the top cover and check the tone generators (12 little black "barrels"). There are 12 generators in total, one for each note in all octaves. Try to adjust trimpots on the generators.

Apr 24, 2008 | Yamaha Audio & Video Receivers

1 Answer

The Output Volume Is Extremely Low!


Sometimes the rear channels can be used as a 2nd zone. Does the unit have A&B speaker selection on front panel? Usually if it has a 2nd zone it will say in owerns manual or on back of unit or on front panel as well. That is when you have the option to adjust the volume in the menu on the 2nd zone. GURU JAY

Feb 07, 2008 | Sony STR-DE545 Receiver

1 Answer

Led display goes dead


I suspect intermittent 31V supply, filament supply or bad connections on fluorescent display.
Check Q801 31V reg , R802, zener on base of Q801 located on DC board. Inspect all boards for bad solder joints, reflow and tighten pcb grounding screws.

Oct 23, 2007 | Sony STR-DE635 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

597 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...