Question about Zebra Z4M Printer

1 Answer

Error in Print Jobs in the Queue

Hi,
I have about 6 Zebra Z4M printers which are shared across the network. It prints labels in large amount. Often we get errors in the printer queues ans stops printing. On deleting/ Restart the top printer job, printing resumes. We are baby sitting this issue whenever it occures. Is there any permanent fix for this issue??

Posted by on

  • 1 more comment 
  • stevephi Dec 12, 2008

    I have the same problem and my printer is setup via IP/TCIP (Static IP)


    Steve


  • bzeb Jan 28, 2009

    I have a similar problem, but turning the printer off and back allows the printing to resume. However, the errored job doesn't print.

  • Tim Babcock
    Tim Babcock May 11, 2010

    How are these printers connected?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 185 Answers

The use of a Print Buffer will help, the problem happens when there is a buffer overflow. Reboot the printer and let the print queue to resume will fix it every time, a print buffer will help with the overflow, try get one with a fair bit of RAM

Posted on Oct 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I set up Zebra Z4m to print Adobe Forms Label?


If it's in pdf, then just print it with the printer driver

Dec 11, 2014 | Zebra Z4M Printer

1 Answer

I have a Zebra Z4M printer. We use it to print on various labels - pre-printed and blank labels (semi-gloss). I've been struggling to print on one of the pre-printed labels. Everything else prints...


some labels are hard to calibrate, nee to calibrate the sensors with manual calibration.
1} go to the MEDIA AND RIBBON CALIBRATION,
2}take 2 or 3 labels from the base paber, load the way to the based paper stay unther the sensors, 3}close printhead.
4} press ok.
5} Move the ribbon out from sensors and close the printhead.
6) press ok
7) wen printer ask RELOAD ALL, load the labels correcly and the ribbon, close the printhead and the top door, and press ok. The printer run the calibration it self.
wen finish, saved (press setub twice) and test.

Jan 21, 2011 | Zebra Z4M Printer

1 Answer

Z4m printer will miss labels in jobs. I've saved the job in the spooler and if I resend the jobs the blank labels will print out so I know the job is good. Any suggestions welcome.


Check the label size is set correctly in the application. Try using a driver from Nice Label or Seagull Scientific websites to suit Z4M (Not Z4M Plus). Recalibrate the printer and try again. Remember to setup the driver correctly because the driver will override the printer settings.

Nov 30, 2009 | Zebra Z4M Printer

1 Answer

Printing loop


Hello,

Have you tried sending print jobs thru the parallel port only? I think it has to deal with your jetdirect box. You can try reseting that as well.

Rory Cardenas
Midrange Repair and Parts
Alsip IL 60803
708-597-4222 x240
rcardenas@mrp.to
AOL IM: RORYMRP

May 26, 2009 | Zebra Z4M Printer

1 Answer

Zebra Z4M only feeds a small portion of the label.


You should try a factory reset. Power off the printer. Hold the "pause" and "feed" buttons down while powering up. Allthe lights will blink and when they stop blinking, release the "pause" and "feed" buttons. This will factory reset the printer.

Apr 24, 2009 | Zebra Z4M Printer

2 Answers

Can't print images on zebra z4m printer


Check the "Dithering" setting in the printer driver. Turning "Dithering" on improves graphics but reduces speed of processing.

Apr 07, 2009 | Zebra Z4M Printer

1 Answer

Z4m zebra printer problem


Might foul the ribbon sensor, clean the sensor and try to print again.

Mar 02, 2009 | Zebra Z6M Plus Thermal Label Printer

1 Answer

Zebra Z4M Communication


Yasemin, the most practical solution is to design your label on a software like a label matrix or zebra designer and print to a file and have the ZPL codes. Roberto Martinez Mexico bartech9@yahoo.com.mx

Feb 27, 2009 | Zebra Z4M Printer

2 Answers

Label Printing stuck in queues


I think your problem comes from your spool server. Check if you can select not to reprint on errors. As far as the error issue is concerned, i need to konw the reason of the errors to help

Jul 21, 2008 | Zebra Z4M Printer

Not finding what you are looking for?
Zebra Z4M Printer Logo

840 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Printers & Copiers Experts

pkwc

Level 2 Expert

254 Answers

lancer284

Level 1 Expert

35 Answers

kenneth njonjo

Level 3 Expert

1575 Answers

Are you a Zebra Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...