Question about GE D52GW12 52" Rear Projection HDTV-Ready Television

1 Answer

Power button wont turn off

My GE was taking really long to come one, it would blink twice cut off and i would have to go through that series about 8 times but would finally come on. Today it started blink continuously and wont come on, any suggestions?

Posted by on

  • dazeygirl67 Jul 15, 2008

    I can't take it back, I got it about 3 years ago.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 97 Answers

Take it back, faulty.

Posted on Jul 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install timing chain kit


If it's your first time. You really need a manual. A set of metric wrenches, sockets, and a breaker bar. Also a floor jack. The job will take about 3 hours, but for a first timer. Count on at least 8 hours. The book will go thru the procedure and tell you the timing marks. Timing marks are critical. Don't cut corners. When it tells you to turn the crank by hand twice, do it. Using the starter to do it can and will trash the head or engine.

Apr 29, 2014 | 2001 Saturn L-Series

1 Answer

Error 5100


Hi,

It must be hard for you having this issue. Here, do these steps correctly, it will help you fix this issue.

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button twice then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should work normally.

Thank you for visiting FixYa! I really hope I made your day! Enjoy!

Apr 16, 2011 | Canon PIXMA MP520 InkJet Printer

1 Answer

How do I play regional dvd's that the player is not tuned to. I have been trying to find a code but I am struggling. Can you help me?


Hi
You need to follow these instructions.


To unlock the Region Code on a Panasonic DMR EZ48 using a One for All - URC 7040



1. Switch on the player (make sure the drive select is DVD).
2. Select DVD on the URC.
3. Hold the magic button on the URC until the DVD button on the URC blinks twice
4. Enter device code 0490 on the URC, (DVD button blinks twice), URC takes control of the Player.

Point the URC at the Player and program the URC buttons using the following procedure:

1. Hold magic button until the DVD button on the URC blinks twice
2. Press 994 (DVD button blinks twice)
3. Briefly press magic.
4. Enter 4 digit code 1911 (DVD button on URC blinks twice)
5. Repeat steps 1, 2 & 3
6. Enter 4 digit code 1202 (DVD button on URC blinks twice)
7. Repeat steps 1, 2 & 3
8. Enter 4 digit code 0653 (DVD button on URC blinks twice)
9. Repeat steps 1, 2 & 3
10. Enter 4 digit code 1804 (DVD button on URC blinks twice)
11. Repeat steps 1, 2 & 3
12. Enter 4 digit code 1435 (DVD button on URC blinks twice)
13. Repeat steps 1, 2 & 3
14. Enter 4 digit code 1556 (DVD button on URC blinks twice)
15. Repeat steps 1, 2 & 3
16. Enter 4 digit code 1227 (DVD button on URC blinks twice)
17. Repeat steps 1, 2 & 3
18. Enter 4 digit code 1178 (DVD button on URC blinks twice)
19. Repeat steps 1, 2 & 3
20. Enter 4 digit code 1299 (DVD button on URC blinks twice)
21. Repeat steps 1, 2 & 3
22. Enter 4 digit code 1230 (DVD button on URC blinks twice)

23. Press the One For All URC buttons in the following sequence

1, 2, 3, 4, 5, 6, 7, 8, 9, THEN hold down 0 until "HELLO" appears in the display;

After about 1 minute the Player comes back to life as Multi Region.



--

-


Please dont forget to vote if you liked my answer


thanks

------




Feb 13, 2011 | Panasonic DMR-EZ48 DVD Recorder

2 Answers

Bose 321 series wont play region 1 dvd


To convert Bose 3-2-1 GS Series 2 DVD system to Multi-Region playback

1. Press the Right button on your remote control
2. Press the Up button on your remote control
3. Press the Shuffle button on your remote control
4. Press the Stop button on your remote control
5. Press the Mute button on your remote control
6. The disc tray should eject twice to confirm the region change
7. Press the Standby button on your remote control to power off your machine
8. After one minute, press the Standby button on your remote control to power on.

Done!

Nov 29, 2010 | Bose 3 2 1 GS Series II DVD Home...

1 Answer

What are the codes ge tv


The codes are, 0047,0051,0178,1147,1347,....Step 1. Turn on TV, 2. Press TV button, 3. Press and hold SET button until LED blinks twice, then release, 4. Enter one of the four digit codes, the LED will blink twice, 5. Aim the remote at the TV and press the POWER button, if your remote don,t have a Power button, press PLAY, the TV should turn off, if not, try 1-5 again using a different code....hope this was helpful....

May 22, 2010 | One For All URC-3021 Remote Control

1 Answer

I have the radion shack hdtv remote. Cat no


Download the manual and codes from here

http://www.remotecentral.com/cgi-bin/files/dl.cgi?file=others/radio_shack/15135-manual.zip&area=other

Here is how to set the code...

1. Turn TV on
2. Press TV button on remote
3. Hold P button on remote until LED blinks twice
4. Enter the first 5 digit code for Magnavox TV's
5. Press Power button - TV should turn off. If TV doesn't turn off repeat steps 2-5 with the next 5 digit code, until either TV goes off or run out of codes.
6. If out of codes use searching for code method below...

TV codes for Magnavox

10047, 11454, 10054, 10154, 10000, 10250, 10051, 10180, 10060, 10030, 10171, 10092, 10706, 11913, 11904, 11755, 10019, 11365, 11254, 10802, 10386, 10282, 10020, 10187, 10186, 10024, 10179, 10096

Searching for code

1. Turn on TV.
2. Press TV button on remote
3. Press and hold P button until LED blinks twice
4. Enter code 991 on remote - LED blinks twice
5. Press 1 - Device key blinks twice
6. Press Power button once
7. Press and release CH+ key until TV turns off.

At this point in the manual, the manual is only correct depending on what type of TV you have.

In the manual if you press the Power on button the TV should turn itself back on, the fail to state that not all TV's turn on by the power button, the majority now are triggered to turn on, on channel change, however you can't use channel change here to check it as you'll go to the next code... here is my solution...

8. Turn TV back on either using original TV remote, or buttons on front (most TV's if you change channels they come back out of standby mode, very few now turn on by pressing the power button).

9. Press Power button on remote - TV should turn itself off again.
10. Press P button on remote to lock in that code.

If the device does not turn off press CH- to go back through the codes, press and release P button when TV turns off.

Finding code

If you used the search function you might want to know what code it's using. To do this follow these instructions...

1. Press TV button
2. Press and hold P until LED blinks twice
3. Enter 990 and LED blinks twice
4. Press 1 and count number of times LED blinks this is the first digit of your code (e.g. 1 blink = 1, 2 blinks = 2, etc).
5. Repeat step 4 pressing buttons 2 - 5 for the other digits (e.g. for the second digit press 2 count number of blinks.. etc)

At this point the manual doesn't tell you how to get out of this mode, I presume pressing any other button on the remote other than 1-5 will take you out of this mode, either that or leaving the remote alone for 5 minutes.

Nov 08, 2009 | Radio Shack (15-2147) Remote Control

1 Answer

I need codes for urc 3220 on a ge tv


GE
002 006 007 018 107 114 310 312 502 601 704 719 803 806 810 901 911
Follow these instructions
carefully. These are as close as i can get you
to getting you operations...the rest is up to
you. GOOD LUCK!
  1. PRESS the button for the device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER the 3 digit code for your brand.
  4. You should receive 2 quick flashes after entering your code.
  5. PRESS the POWER button to test the code.
If you have tried all of the set-up codes for your brand of equipment, or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
  1. PRESS the button for device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE(TV,VCR,CABLE,etc.) button until your device turns off.(On VCR,LD,and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.
Blinking Back the Code:
  1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 0.
  4. PRESS 1, carefully COUNT the number of blinks. (1st digit)
  5. PRESS 2, carefully COUNT the number of blinks. (2nd digit)
  6. PRESS 3, carefully COUNT the number of blinks. (3rd digit)
If the remote DOES NOT blink it means the number is 0.
This is your 3-digit setup code.

Jun 24, 2009 | GE 27GT271 TV

2 Answers

Cancel Light Flashing on Kitchen Aid Dishwasher


I ran into this same problem. Cutting the power didnt reset it.

After power reset, mine had the normal led blinking. If I pressed cancel, then the cancel and china button leds would start blinking too.

I pulled out the trouble shooting guide (from behind the baseboard kick panel under the dishwasher door). It that if the dishwasher wont run and button LEDs are blinking there is a short circuit in the keypad. It gave a keypad diagnostic sequence which I followed. (disconnect keypad and try to initiate the diagnostic cycle without the keypad by disconecting the yellow leads to OWI sensor twice in less than 6 seconds.

I could hear the diagnostic cycle start, so the problem is a bad keypad. Will order a new one tomorrow and let you know if it works.

Sep 01, 2008 | KitchenAid 24 in. KUDI01FLSS Stainless...

1 Answer

NOTHING HAPPENS!!!!!


power supply probel, need to take to service

May 02, 2008 | Sony FD Trinitron WEGA KV-27FS100 27" TV

2 Answers

SVA TV


Was it working befor you got it off your friend???

Apr 20, 2008 | SVA-USA HD4208TIII-VR 42 in. Plasma...

Not finding what you are looking for?
GE D52GW12 52" Rear Projection HDTV-Ready Television Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69736 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

matt martin
matt martin

Level 3 Expert

1198 Answers

Are you a GE Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...