Question about PC Desktops

1 Answer

Hello I have your D-Link and I would like to get a pin number for this to stop the public from using and do I have to buy one of you packages to do so thanks MAree Haynes

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 77 Answers

No purchase necessary....you will have to get to the web based settings of the router though and set up security settings for your network. In an open internet explorer window type 192.168.0.1 or 192.168.1.1 this will open up a window asking for username and password, use "admin" for both. This should open the settings, under the tab of wireless or wireless security we are going to apply a security feature called WEP, you will need to choose this setting in one of the dropdown menus. Once chosen we will need to choose the type and we want HEX. Now think of a 10 digit number that you can easily remember. i.e. address, combined with license plate etc. On that same page there will be a place for you to enter an SSID. This is going to be the name of your network. Go ahead and check the box for your router to broadcast your SSID so you will be able to quickly identify your network from your wireless computers. You can use a pet's name etc. Once complete make sure you save your settings and log out. Now with each of your wireless computers you will have to disconnect from your network and then try to connect to your network with the new name that you assigned it and then it will prompt you to enter in the 10 digit security key that you entered earlier. Only give the key to your computers that you want using your network.

Posted on Jul 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hp pro 3400 frontpanel pinout


http://h20566.www2.hp.com/portal/site/hpsc/public/psi/manualsResults?sp4ts.oid=5160137&ac.admitted=1418921816948.876444892.199480143


http://h20566.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=5160137&docId=emr_na-c03550750&docLocale=en_US


http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c03550748-1.pdf

Finally I would add that in these manuals, which my not contain the info you want (I should download or save the pdfs to your computer anyway), HP have lumped together q few models and even more motherboards so to me it's not clear which HP part number belongs to your PC. I would that (be careful here) mant motherboards have the same connector header pin-outs, but HP don't tell you what they - only a third party would do this.

18.December.014

Jun 11, 2014 | HP Compaq d530 SFF PC Desktop

5 Answers

How do I uninstall Norton Antivirus 2003


Use this link to remove the anti virus :

click:
HERE


good luck..............

May 29, 2008 | PC Desktops

1 Answer

Reset bios cmos


Read the PDF in the link below on page #3 listed as JBAT1. Open your case and locate the CMOS reset pins. Move the reset jumper from current position (usually Pins 1+2) to reset position (usually pins 2+3) Power on the computer and hit keyboard key (F10) to get to the Bios and check if Bios was reset.. Consider that password protection will not normally be removed on CMOS reset, you will need to ask HP or look around the internet for a way to reset a password protected Bios.
PDF REFERENCE
http://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=3352967&docId=emr_na-c00859615&docLocale=en_US

Jan 14, 2014 | HP Compaq dx2300 Microtower - RT950UTABA...

1 Answer

How do I remove and replace or install memory (RAM) in the gateway zx4351


You need
  • Package: 240-pin DIMM
  • Feature: DDR3 PC3-10600
I included a link or compatible ram from Newegg.com

Click ----->You can Buy Ram here.

Apr 24, 2011 | Gateway ZX4351-47 21.5-Inch All-in-One...

1 Answer

I need to know where to connect the three seperate 2 pin connectors from the ''power switch'' to the motherboard on my eMachines C2685 desktop computer.


The eMachines C2685 uses an FIC VC37GV motherboard. (First International Computer, Inc.)

http://www.motherboards.org/mobot/motherboards_d/FIC/VC37GV/

Here is the motherboard manual,

http://www.ime.org.uk/pdfs/vc37_vg31_b1_eng.pdf

After you click on the above link, give it up to 30 seconds to download. This is a PDF file.

Barring you cannot download the file, I will state the connections for the Front Panel header on the motherboard.
(Plus state the page to reference to, in case you can download)

View the first link, with the photo of the FIC VC37GV motherboard.

As shown, Processor is at the top, Ram Memory slots are to the right.

The Front Panel header is located at the very bottom right corner.

It is parallel to the outside edge of the motherboard. There are two rows of pins.
(Page 12)

The Front Panel header has 5 pins going across the top, and 4 pins across the bottom.

The top row of pins are numbered Odd.
The bottom row of pins are numbered Evenly.

On the Top row starting on the Right side, going towards the left, the pins are numbered 1, 3, 5, 7, and 9.

On the Bottom row starting on the Right side, going towards the left, the pins are numbered 2, 4, 6, and 8.

A) Pins 1 and 3 are for the HDD LED. (HarDDrive activity LED)

B) Pins 5 and 7 are for the Reset switch

C) Pins 2 and 4 are for a Dual Color Power On LED, if used.
Green goes to Pin 2. Yellow goes to Pin 4.

Otherwise Pin 2 is Positive, ( + ), and Pin 4 is Negative. ( - )

D) Pins 6 and 8 are for the Power On switch.
(PWR1, or SW1)

There is a small 3 pin header, just above the Front Panel header. (Page 12)

This is for a Power LED that has either two wires, or three wires.
The pins are numbered from Right to left.

Pin 1 is for the Power LED, and Pin 2 is for Ground, if using a two wire Power LED. (Not dual color)

Pin 1 is for the Power LED, and Pins 2 and 3 are for Ground (GND), if using a three wire Power LED.
(Page 13)

May 26, 2010 | PC Desktops

1 Answer

I want to replace CD drive on Dell Dimension 8200. My options are serial ATA, parallel ATA & ATAPI. Which one do I need?


Hello,

This computer has 2 IDE connectors. These are parallel ATA connectors.

See: Dell Dimension 8200 Specs

If you get a drive, look for IDE on the package. IDE, PATA and ATAPI are near synonomous. They use a 40 pin flat ribbon cable to connect.

Thanks for using Fixya.

Nov 25, 2009 | Dell Dimension 8200 PC Desktop

3 Answers

Does the Compaq s3310cl support a DVI monitor? I am looking at the Samsung 2243swx but it's only a DVI monitor and has no VGA capability. I can't find any info on whether my computer supports this kind of...


Hello, the integrated video card in the Compaq s3310cl doesn't have a DVI port, however you may purchase and DVI to VGA adapter which should allow you to hook up that Samsung 2243swx Monitor. Be aware there are various types of DVI connectors so match up the connector you require for you Samsung Monitor.

d8b8bed.jpg Thanks

Ryan
Cobalt Systems
DVI Connector Guide DVI-D Single Link DVI-A DVI-I Single Link Digital Only Analog Only Digital & Analog dvi_ds.gif dvi_a.gif dvi_is.gif Two sets of nine pins, and a solitary flat blade One set of eight pins and one set of four pins, with four contacts around the blade Two sets of nine pins and four contacts around the blade DVI-D Dual Link DVI-I Dual Link Digital Only Digital & Analog dvi_dd.gif dvi_id.gif Three rows of eight pins and a solitary flat blade Three rows of eight pins and four contacts around the blade

Sep 21, 2009 | Compaq PC Desktops

2 Answers

Ram questions


it has 1 gb ram. if you bay 1 gb it will be 2 gb.  if you buy 2 gb you can use together but it supportes only 2 gb. you can only see 2 gb.

May 27, 2009 | Sony VAIO VGC-RB53 PC Desktop

3 Answers

I need to know which Pentium 4 cpu my mobo could take. It has a chipset: Intel 82845Gl Revision B1/ Intel 82801DB ICH4. Would it take an FSB 8oo MgHz and run it at full speeed or would it clock down to...


check your pin packging. if it is 478pin packaging then you can upgrade only to that.
but the current processors use lga775 packaging. check the processor pin packaging before upgrading.

Apr 20, 2009 | E-Machines eMachines Desktop PC

1 Answer

Is there any way i can download the software fromthe installation disk for the Brother MFC=240C?


Hi - there is a link below for you where you can download the drivers and software. Just choose all in the first box, your operating system in the second box and your language in the third. You can download the full driver and software package. If this solvws your problem PLEASE rate this as fixed. If you need more help just add a comment and I'll be happy to help. Thanks.

http://welcome.solutions.brother.com/bsc/public/us/us/en/dlf/download_top.html?reg=us&c=us&lang=en&prod=mfc240c_all

Jeff

Jun 01, 2008 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...