Thinking about purchasing .Are there any main areas of problems/faults or modifications required on a '55 plate machine?(15k on the clocks)

As fitting a tow bar to the vehicle requires a modification plate to be fitted to keep it legal I suggest that you have the job done by accredited tow bar fitting specialists. They have the correct wiring loom and the plate to fix to the vehicle for the modification

I don't see why you should have any problems as long as you don't exceed to current supplied by the circuit breaker, and since your basically not going to be drawing much more current from your 13.5K unit to the 15k unit I would say that you should not have any problems.

If your happy with my suggestion would you kindly rate me.

Good luck,

Marty

The modification you quote would have been issued from the manufacturer and should have been applied at a service point or you should have been notified to present the vehicle for the modification at a suitable time . I take it that you purchased the vehicle new from the dealer. I would approach the dealer manager and ask why the modification was not carried out under warranty and ask that it now be done free of charge. If he refuses then the friendship ends and I suggest a talk with legal council to have the matter dealt with as all modifications have to be carried out either inside or outside warranty. IT will have something to do with a recognised engineering design fault which will override any warranty period .

The fault code F1 (or F01) is a Motor/triac fault. The triac is a device for controlling the relatively high currents required by the washing machine motor from the low power chips etc on the main Printed Circuit Board (PCB). Either the motor or triac has a short circuit condition. Check connectors on motor and main PCB card making sure they are sound and not lose. If the connectors are ok I would replace the triac or power board.

because you have not mentioned what transmission you have I will start with a manual. I am thinking that the clutch pressure plate is on the way out and is slipping in the peak torque of the engine and allowing the engine rpms to peak out. Check clutch slave cylinder and clutch master cylinder as the compensating port may be blocked and holding the clutch partially disengaged. If you have an auto- run fault codes and look for an OD servo/sensor fault. Have a pressure test done on the box to check for internal faults. Check oil level when hot

hi.
most cars run licence plate lamps on the same fuse as the tail lights.
if your tail lights work, then it is more likely to be a fault on the bulbs or bulb holders, or the wiring in that area, probably caused by the crash.

i would recheck this area first, using new bulbs to rule these out.

Are you in UK using 220V AC or in USA using 120V AC?
Service & Spare Parts
If after carrying out the necessary checks there is still a fault with your appliance please contact your local AEG Service Force Centre. In guarantee customers should ensure that the suggested checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service calls.
Service & Spare Parts If you require a service engineer or wish to purchase spare parts, contact your local AEG Service Force Centre, by telephoning: Help us to help you Please determine your type of enquiry before telephoning. When you contact us we need to know. 1. Your name, address and post code. 2. Your telephone number. 3. Clear and concise details of the fault. - What is the fault? - When does the fault occur? 4. The model, production number and product identification number. 5. Date of purchase. This information can be found on the rating plate, so you have these numbers to hand we recommend you write them below. Customer Care For general enquiries regarding your AEG appliance, or further information on AEG products please contact our customer care department by letter or telephone at the address below or visit our website at
www.aeg.co.uk.
Customer Care Department AEG Domestic Appliances 55-77 High Street, Slough, Berkshire SL1 1DZ
Tel: 08705 350350*
*Calls to this number may be recorded for training purposes. 0870 5 929 929
===============
Here is the FULL User Manual Link HERE
===============
UK parts site
Link HERE
===============

In short, no. A correctly functional microwave oven should not affect any other appliances.

I can offer no comment regarding your last Bosch washing machine as you haven't given any specific details, but as with all brands there are sometimes models which are found to require in-service modifications and service bulletins and modification kits are then made available to engineers. I haven't ever heard of the modification which you mention on any Bosch washing machines though and it's not mentioned in my service bulletins folder.

If both the remote and the front panel buttons do not work, I would be thinking that it is a problem with the TV's main uPC area. This type of fault can be involved, and would require factory level service where the fault can be properly analysed.

I can tell you in advance, that this type of fault can be expensive to service.

Jerry G.

Hi the problem with you fridge.. The evaporator is full of ice.. caused the the back plate on you machine.. this is a common problem.. requires new back plate ***.. This has been modified.. The defrost heater do go also now and then. But look at the back plate first.. Due to the modification... Kind Regards mcdapp.