Question about Hitachi 43UWX10B 43" Rear Projection Television

1 Answer

Blue won't line up at the top in digital array

Have a blue shadow at the top of my tv screen. Attempted to line up digital array & it worked once but, went back within 2 hours.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hitachi Master
  • 8,617 Answers

You need to replace both convergence ICs and the six 1 watt feed resistors. The ICs are both STK392-110 and the resistors you need one of each RK42 3.3 ohm 1watt, RK46 1.8 ohm 1watt, RK50 2.7 ohm 1watt, RK54 1.5 ohm 1watt, RK58 3.9 ohm 1watt and RK62 2.2 ohm 1 watt.
You can get replacement ICs and resistors at the following link with free instalation instructions.
http://servicemanuals.vstore.ca/

Posted on Jul 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is a blue shadow (especially around on screen graphics, lettering etc.) when in HD mode. I attempted to align the colors through the color convergence but the blue alignment did not work. I also...


No.This tv have a convergence problems,it dead.The tv have R,G,B colors lines mis alignments,have colors shadows pictures or 3D pictures look alike?The tv convergence board,must be repaired by repacling 2 STK convergence ICS and some or all of it resistors too.To fixed the tv convergence board,to solved the tv picture convergence problems.The shop,will cost u like $300-350 for parts and labors.

Feb 14, 2011 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

Blue shadow around picture. tried digital array blue won't converge. red and green work


Projection TV sets are known to have two common problems. The first problem that is common to these sets is convergence failure. When this happens the TV will usually look 3D, Wavy/Distorted, etc. It may also shutdown and blink an error code.

The second common problem with Projection TV sets is dull video, halos around objects, white looking video, or red overpowers the screen. This is commonly caused by the fluid in the lens being clouded over.


You can find more details and solutions here on Fixya at the following link below. Or click HERE

3d884ac.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dul

Dec 02, 2010 | Hitachi 43GX10B 43" Rear Projection...

1 Answer

I have a Hatachi 43gx10b anf have a blue shadow that is warped, not straight, around the picture. I've tried the digital array but it won't converge the blue but the green and the red work. What can I...


Projection TV sets are known to have two common problems. The first problem that is common to these sets is convergence failure. When this happens the TV will usually look 3D, Wavy/Distorted, etc. It may also shutdown and blink an error code.

The second common problem with Projection TV sets is dull video, halos around objects, white looking video, or red overpowers the screen. This is commonly caused by the fluid in the lens being clouded over.


You can find more details and solutions here on Fixya at the following link below. Or click HERE

3d884ac.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dul

Dec 02, 2010 | Hitachi 61SWX10B 61" Rear Projection...

2 Answers

Hitachi 61UWX10BA Convergence Still Off After Chip Replacement


Remove Front bottom Panel thier you will see front of convergence board there is a small blue contact switich with TV on press and hold it for 5 sec then you should see convergence Pattern so you can aline convergence correctly I have the whole Manual to tv just have to find it. anyway for now try this.

Dec 01, 2009 | Hitachi 53UWX10B 53" Rear Projection...

1 Answer

Weird blue flash when tv turns on or off


TV will need service soon, blue CRT is on its way out, will need replacing

Mar 25, 2009 | Sony KP-51HW40 51" Rear Projection...

1 Answer

Toshiba 50HX70 Convergence reset


press mute button once after press and keep pressing mute again and press de menu button on tv .when tou see S on screen press 7 you are in convergence adjusting mode

Aug 03, 2008 | Projection Televisions

1 Answer

RCA 52" HDTV Rear Projection TV MM52110JX1


Replace FL231 400ma fuse. this will fix your problem.

Oct 26, 2007 | RCA D52W19 52" Rear Projection Television

1 Answer

Digital Array?


I have the very same problem. Was there a solution to landfill2004?

Nov 13, 2006 | Hitachi 50GX30B 50". Rear Projection...

Not finding what you are looking for?
Hitachi 43UWX10B 43" Rear Projection Television Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hitachi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...