Question about Dishwashers

1 Answer

Water sitting in bottom of dishwasher

Kenmore Quiet Guard 1 Dishwasher Model number 665 110733420
I'd be happy to figure it out if I could find an online manual
Thanks, Sandra

Posted by on

  • bloomergurl Jul 15, 2008

    Yup, I'm in Canada.  Thanks for trying anyway.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 868 Answers

Are you in Canada, I can't find the info you need if you are. Although I'll try with Whirlpool in the morning for you.

Posted on Jul 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my Kenmore quiet guard 3 dishwasher not heat water


Go here.
http://www.searspartsdirect.com/
Click on select- Model Number - Enter your model number.

Owners manuals diagrams, parts lists, order parts--
One of the best reasons to buy from sears!

Oct 01, 2014 | Dishwashers

1 Answer

I see the pressure tower for a Kenmore Ultra Wash Quiet Guard dishwasher laying in the bottom of the dishwasher. I've just rented the house and haven't used the dishwasher yet. Does this pie


No, the designers put it in there for a reason; it won't work as well without it, as it would with it in. Probably the mounting tabs are broken or sprung. A new tower isn't very expensive. You can probably get one from SearsPartsDirect.com, RepairClinic.com, EasyApplianceParts.com, or AppliancePartsPros.com.

Mar 28, 2012 | Kenmore Dishwashers

1 Answer

I have a Kenmore Dishwasher Quiet Guard 1 Model Number 665.1784440. It will not fill up with water, but it will drain if I pour water into it. Help


start simple, make sure water supply is ok. if this ok i would be lookin at the inlet valve, its solinoid could be faulty. located inside dishwasher where water hose screws on.

also on dishwashers a broken wire inside the door skin where wires loop into bottom would be fairly common.

Sep 25, 2010 | Dishwashers

1 Answer

Kenmore Ultrawash Quiet Guard 5 making buzzing/grinding noise


I have a very similar dishwasher, with a very similar problem. I fixed it by removing debris from the water evacuator pump located towards the front of the bottom of the machine (the last motor before the drain hose. In my case, grape stems had clogged it up. Once emptied, it purrs once again. NOTE: don't disassemble the motor, just flush it out, there is an o-ring gasket that is a bear to re-install.

Jun 22, 2009 | Kenmore 24 in. 15689 Built-in Dishwasher

1 Answer

Water keeps coming back into dishwasher after cycle is done


sounds like maybe one of your check valve is not working right.

Jun 03, 2009 | Dishwashers

2 Answers

Where is the filter on a Kenmore Quiet Guard 2 dishwasher?


I have a Quiet Guard 4. Same problem so will describe my solution.
1. Remove bottom basket. Remove top basket.
2. Remove bottom washing arm. Unscrew (Gently but firmly) the centre post. Lift arm assembly up and out.
3. Remove overhead conduit. One screw at back, one at top (Philips #2 bit). Rotate whole assembly 45 deg right (Clockwise) and lift off of centre post.
4. Remove centre post (Pull straight up). Remove 4 screws (Star T-20 bit). Lift whole assembly out. Pop off screen and clean.
5. Remove cap over cutter/chopper. There is a single screw at front left (under assembly removed in 4). Remove screw (Star T-15 bit) and cap (Needs some wiggling to free it up). Remove cutter and filter. It is on a spring loaded pin. Pull the cutter blade foreward and then the filter disc straight up. Clean thoroughly as it may be the cause of your problems.
Reassimble. Good luck!

Dec 09, 2008 | Dishwashers

1 Answer

Where is the filter on a Kenmore Quiet Guard 2 dishwasher?


not a dumb question,
is the bottom dishes coming out clean? there is a chopper that breaks and will trap food and not clean the top rack.it is not easy to replace.but not impossible.

Oct 23, 2008 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Help


wow that could be a tough one there is no door lock on a dishwasher only a door latch what happens when you depress the door latch and can you send me a model number so i can pull up the blue prints and see if we can figure out a way to open it try pushing on the door and depressing the latch at the same time let me know what happens

Jan 10, 2008 | Kenmore 24 in. 15932 Built-in Dishwasher

2 Answers

Kenmore Ultra Wash Quiet Guard


That looks more like the serial number. Check again to confirm the model number.

Sep 09, 2007 | Kenmore 17252 Free-standing Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,000 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...