Question about EnGenius ECB-3220

1 Answer

Site survey no signal

Hi sorry for my english, i have senao acces point sometime this no detect signal in site survey option,

help me please!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 481 Answers

Site Survey is meaningful only in bridge mode, not access point mode. Assuming you are operating this unit in bridge mode, it could be possible that no signal is being detected because there are no access points nearby for it to detect. If you know that there are, in fact, working access points in the vicinity, then my first suspicion is that you have a faulty unit.

Posted on Nov 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HI SENAO 2611CB3 DELUXE REPAIR IP DONT HOW TO RECOVERY IP IP 192.1681.1. DEFAULT NO ANSWER NO CONNECTION THANKS LOST DEFAULT IP SAMMY


192.168.1.1
if you cant open it then reset router by pressing with toothpick the tiny button for 5 seconds while its on power.
if i was helpful please vote ..

Nov 01, 2010 | D-Link Wireless Access Points

1 Answer

Noy finding ip address senao wireless AP


Hi. Here is the manual.

http://www.senao.com/images/www.senao.com_English/NL-2611CB3-PlusDelx-Manual-V1-0.pdf?CATNO0=D&CATNO1=D3&CNT=1

Set your PC to use the static IP 192.168.1.10, netmask 255.255.255.0.

To login to the web manager, go to http://192.168.1.1. Leave the username and password blank. You can now configure the device and assign IP address etc.

Jul 18, 2009 | SENAO NL-2611CB5 PLUS (NL2611CB5PLUS)

1 Answer

CANNOT LOGIN TO MY SENAO DUE TO FILTER PROBLEM


press the reset button n configure it again

Nov 27, 2008 | Wireless Access Points

1 Answer

Finding of IP for the senao 3320 ext.


repair center, visit : http://www.gblmedia.com

Oct 03, 2008 | SENAO NL-2611CB5 PLUS (NL2611CB5PLUS)

1 Answer

Engenius


Enter the configuration utility inside the unit and run a signal survey. If the survey does not detect any access points, your radio section has gone bad. If it does detect the appropriate access point, examine the signal and noise numbers associated with the access point. For a reliable connection, there should be a difference of at least 18 between the two figures.

Jun 28, 2008 | SENAO NL-2611CB5 PLUS (NL2611CB5PLUS)

1 Answer

Confirguration


Hi,

After installing the hardware and physical mounting, basic configuration is something like below:

1. Set your computers TCP/IP address temporarily to be a static IP address such as 192.168.1.5;
2. Open your browser and type in 192.168.1.1 in the address bar. The EnGenius password prompt should appear. The default user is admin and the password is also admin. The control interface should now be accessible;
3. Under the Wireless heading click on Site Survey. This will display all the access points in your area. Your ISP or to whatever WiFi network you would want to connect should be listed in the ‘Wireless Site Survey’. Select the access point with the highest signal level or your choice. Click ‘Connect’;
4. After clicking ‘connect’, it should confirm that the EnGenius has connected successfully;
5. Click Ok and it will take you back to the list of wireless site surveys;
6. To confirm that the SSID has been changed go to the ‘Wireless Basic Settings’ page which is in the Wireless submenu in the left side bar. Once on the wireless page go to the box with SSID. The value should read "Your ISP or the WiFi network you would want to connect"; this has to be exact and case-sensitive to connect successfully.

This is just the start, all settings are configurable and actually depends as to how you would want to use the device; as a WiFi Access Point, as a client router mode or Wireless outdoor bridges in WDS mode.

After all settings have been changed to your requirement(s), go back to the PC's control panel and your network connections, and change your TCP/IP address back to DHCP settings (obtaining an IP address automatically). panel window.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

May 15, 2008 | EnGenius EOC-3220 (EOC3220)

1 Answer

SENAO EOC 3220 CONNECTIVITY PROBLEM


hello!

-- try to change wireless channel on your access point
-- try to enable wireless security on your wireless network
-- try to assign static ip address on your wireless computer

Apr 26, 2008 | EnGenius EOC-3220 (EOC3220)

4 Answers

Resetting the senao eoc-3220 long range wireless access point/bridge


Start a HyperTerminal session: Click Start and then select Programs -> Accessories -> Communications -> HyperTerminal. c. Set baud rate as "38400", data bits "8", parity "none", stop bits "1", and flow control as "None". Then press "OK" to bring up the HyperTerminal window.

Feb 21, 2008 | EnGenius EOC-3220 (EOC3220)

3 Answers

I made firmware 1.39 to SENAO ECO3220


hey maick, I have the same proble, but I fix it, try this: 192.168.1.254, for me work fine, after that I reload the new firmware. now is working fine. good luck, jose luis Ogawa

Jan 19, 2008 | EnGenius EOC-3220 (EOC3220)

2 Answers

Senao 8610 not working


Are you saving your settings when you exit the setup screen?

Johnlgrn

Dec 29, 2007 | EnGenius / ECB-8610 / 54Mbps / 802.11a/b/g...

Not finding what you are looking for?
EnGenius ECB-3220 Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top EnGenius Wireless Access Points Experts

Josemuri

Level 1 Expert

32 Answers

rich2481

Level 2 Expert

286 Answers

Are you an EnGenius Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...