Question about Miele Washing Machines

1 Answer

My miele w1926 water valve keeps running all the time no matter what cycle i choose,if i disconnect the water valve it shuts down,so it is beeing commanded to come on fromt somewere,the question what is commanding it all the time

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 172 Answers

You could have a bad mixing valve. I would suggest replacement.

Posted on Jul 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Miele W1926. The red light over the faucet icon is on at the end of the cycle and the final spin cycle doesn't go on.


Check the screen filter where the cold water line attaches to the machine. Clean both hot and cold.

May 02, 2015 | Miele W1926A Front Load Washer

1 Answer

How to put top back on miele w1926


1 Remove stacking kit from top of unit.
2 Reatach the two plastic clips to the back of washer.
3 engage the two slots on the washer top into the clips , pull forward drop lid down on top of washer then secure with two screws on either side of lid.

Dec 29, 2013 | Miele W1926A Front Load Washer

1 Answer

Miele Touchtronic W1213 Front Load Washer: The washer keeps adding and then draining water continuously. One time, the cycle ended and the machine continued to add water and drain endlessly....until I...


hi - If I remember correctly this particular series had a time related sequence built into the programme, whats happening is the timer has picked up the false readings when the pressure activates the switch.

Suggestions to look into - leave power off & turn water back on - does water run into the machine (faulty valve); turn power on initiate a cycle water runs, then turn power off - is water still running? (faulty valve)

From experiences on the field, theres a slim chance that the pressure tube has a hole in it from the vibrations over time. This effect will not create enough pressure in the tube to activate the pressure switch, the only other problem would be the pressure switch itself.

May 17, 2011 | Miele Touchtronic W1213 Front Load Washer

1 Answer

Miele W1926 check inlet light flashes at he end of rinse fill


Hi Yugin.That indicates your machines water inlet valve is faulty.(Means it's taking less water then normal)Please check this steps & do it fast before water inlet is finishes:1-Turn your machine on & run empty with pre-wash cycle first.2-Please ajar the detergent drawer & check runing water on compartment one 3-Please press pre-wash button & compare the running water volume on compartment two.If the running water volume 1 is less then 2 or vs.water valve needs to be replace.That's causing problem.I hope that helps.Thanks.

Jul 26, 2010 | Miele W1926A Front Load Washer

1 Answer

Miele W1926 check inlet light flashes at the end of rinse fill. When the fill ends, the light goes off. I cleaned all 4 filters at the intake hoses. The problem still exists. What does it mean?


Hi dear.It sounds like you'll need to change water inlet valve very soon.Because,machine waiting water level to be reach,in specific time frame in chosen program parameters to be get completed.If that does not happen,then it starts giving fault indication.Indication stops after fill,because task been competed & computer disregards the fault.If that won't happen then machine going to get stop completely & indication will carry on.Chage the water inlet valve if you can.I hope that helps. Thanks.

Jul 25, 2010 | Miele W1903A Front Load Washer

1 Answer

Miele W1926 check inlet light flashes at the end of rinse fill. When the fill ends, the light goes off. I cleaned all 4 filters at the intake hoses. The problem still exists. What does it mean?


Hi dear.According to what you're saying,It has faulty water inlet valve.Machine unable to get enough water to do it's cycle in given parameters in time period & starts giving error but before the cycle complates,however it takes enough water,that's why error lights goes off.If you can,you need to change the valve or call service department.I hope that helps.Thanks.

Jul 25, 2010 | Miele Novotronic Premier 500 Front Load...

1 Answer

Can i use my W1926 in New Zealand where they have


Hi Ekruijver.As I know USA electric standarts diffirent then New Zealand.Your machine should not be use in there unless if you purchase one of those step down transformer for it.That could not be inexpensive solution anyway.That can help.Please check this web site:http://www.tortech.com.au/category/595/ They might able to help you for this issue.OR MIELE NEW ZEALAND.Thanks.

Apr 27, 2010 | Miele W1926A Front Load Washer

1 Answer

Miele W1926 washer shakes more then usual when spinning at low speeds. Could it be problem with shocks? How to open the machine? Thanks


I'd start simply.

They do move over time and if the floor is not even the machine will be out of balance.

If you have not done so check the machine is still level and all feet are solidly on ground.

Try to shake the machine by hand and see if is solid on the ground. There are leveling legs under the unit you can adjust.

Hope this helped. Please rate answer if it does.


Mar 11, 2010 | Miele W1926A Front Load Washer

2 Answers

Miele W1926 water light flashes


That happened to me too. If the machine is a few years old and the hoses are not kinked it's possible the water inlet valve needs to be replaced. On this machine there is a triple cold water valve and a single hot water valve. Mine needed the triple valve and it is about $300 if I remember. Check to see if it's the cold or hot water valve by looking at the water filling through the soap drawer for cold or hot water cycles. When the valves go bad they run but the output is very low which causes the light to flash because it can't fill to the correct level.

You can get to the valves by taking off the top. If you don't feel comfortable working on your own machine have a professional do it.

Apr 25, 2009 | Miele Novotronic W1918A Front Load Washer

1 Answer

No cold water intake


Water inlet valve is bad you need to replace the valve. It is located at the at the back of the unit behind the plate you need to remove that

Feb 14, 2009 | Miele Novotronic W1918A Front Load Washer

Not finding what you are looking for?

Open Questions:

Washing Machines Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Miele Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...