Question about Kenwood Audio & Video Receivers

1 Answer

I have a kenwood DP-R4450 cd player. The disc dawer will not clos completely nor will it reopen.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 71 Answers

It's got jammed - so open her up to try and free it , but be careful -do not force it - only gentle persuasion will help. Then give it a good clean with a 'safe' solvent.

Posted on Jul 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a stereo Integrated Amplifier KA-7010, Multiple Compact Disc Player Dp-M4010. It was a gift from my brother and he cannot find the exact cables that came with the system, and I have a pair of...


More triage first.

Which unit cuts off? Signal Cables won't make either do that. Either will run just fine even without them.

CD players die.

http://www.repairfaq.org/sam/cdfaq.htm

Speaker issues or shorts will pose problems for the amp.

Do you have the manuals? If not, seek them.

Jul 06, 2011 | Kenwood Audio & Video Receivers

1 Answer

I have a VR-407 reciever and I am unable to get my CD/DVD rear outputs to work. I am hooking up a DP-3020 and I can get it to work in the Audio L/R jacks in the front. Is there something that I need to do...


A Kenwood VR-407 is a receiver and has an INPUT pair for CD/DVD, not outputs. Plug ANY functioning audio source (except a turntable) into it and select it on the front panel.

If your DP doesn't work on either I'd suspect something is wrong with IT.




May 24, 2011 | Kenwood VR-407 Receiver

1 Answer

I have a kenwood MIDI M-45 /MIDI M-757 audio system. The CD player won't play. The disc loads but error comes up NO DISC, can you help????


The cd unit is not reading the disc, the laser pickup may be dirty, or the pladder motor that cd sits on may be defective. If you can get at the laser pickup lens, clean it with rubbing alcohol with a Q-Tip very carefully in circular motion and allow several minutes to dry.

Dec 29, 2010 | Kenwood Audio & Video Receivers

1 Answer

Kenwood Stereo


I presume you realize none of these things produces speaker amplification. A receiver would do that and facilitate graceful and simultaneous interconnections. But it's not a necessity for selective interconnective between them, just not all at the same time.

I can't find any details on anything you named except the Tuner.

Typically, the tuner would use an RCA pair to go to a receiver AUX, TUNER or other Line Level input for source selection and amplification. Lacking a receiver, run it to the Tape Deck inputs for recording.

Ditto for the CD changer, but you'll probably have to disconnect the tuner.

Jan 26, 2010 | Audio & Video Receivers

1 Answer

Connection problems


If the CD player has left and right outputs and the receiver has those inputs for a CD or DVD then there's a start.
Speakers...match them up to positive and negative with no power to either component.

Jun 09, 2009 | Kenwood VR-307 Receiver

2 Answers

Ive got a kenwood hi-fi and had it for approximately 15yrs. Its a system where each part is seperate, just recently my cd's have started to jump, ive tried cleaning discs to clean the laser but they do no...


what did u mean by cd's jumping... is it physically jumping.. or is it skipping ...?
Mostly it wud be the wear and tear of the rubber inside.. rubber inside in the sense the motor's belt..

Sep 16, 2008 | Audio & Video Receivers

1 Answer

Kenwood DP-MH5 CD Player won't open or play CDs and display reads err 08. Think a disc may have been loaded incorrectly. How can i fix it?


CDs can be removed but you must use great caution not to break or bend mechanism components. Its better to have unit serviced by pro/tech

May 10, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

ask_not

Level 1 Expert

28 Answers

Fbcgilly

Level 1 Expert

13 Answers

Are you a Kenwood Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...