Question about New World 55WLg Gas Kitchen Range

1 Answer

New World Twinline 3001

I need to remove this fitted oven but have no instructions any tips?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Brute force and total ignorance seemed to work!!

Posted on Jul 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to remove the oven legs so I can put a kick board underneath. How can i secure the oven so it doesn't tilt forward?


most ovens have places at the back for wall attachments to prevent tipping forward
if not make your own

Oct 18, 2016 | Kitchen Ranges

1 Answer

Broken oven lens


Try contacting New World for the information you need.

Dec 10, 2013 | New World Spirit 110 (Gas) Kitchen Range

2 Answers

The element is hot but the fan is not working?


Here is a free video to help you with your cooker fan motor problemsand how to fix them
For all your free videos on appliance repairs remember tomark us down and leave feedback please
For all your parts visit our site http://www.apart4u.co.uk

May 18, 2010 | Belling 335 Electric Kitchen Range

1 Answer

The fan has stopped orking on my new world oven


I have no worked on a new world oven, but i will assume you speak of a convection oven.
Typically convection ovens have a door switch a motor and a run/start capacitor which helps the motor "turn over". I suggest, you have the oven cool, remove anything blocking the convection motor. Take your hand and spin the wheel, then while its spinning turn it on. You may have to try counter or clockwise. If you cant spin it at all, you have a bad motor, if the motor starts up with your manual assistance, the capacitor is bad. If there is not even a hum, a door switch is faulty, that or the motor has a thermal overload (usually a red button on the motor that needs resetting).

Dec 19, 2009 | Rangemaster Classic 110 (Dual Fuel) Dual...

1 Answer

We ordered New World Model 444447275 had it fitted, when we light the oven on full temperature it works for approx 2 mins then the ignition kicks in and the oven goes out. We asked for replacement and we...


it sounds like a install problem . two ranges same problem . either a cooling fan is not working or it require a vent of some kind . i would ck the install very good . at two min its shutting down due to heat . just a thought and may not be the real problem .

Dec 04, 2009 | New World 60GSO Dual Fuel (Electric and...

1 Answer

I am trying to replace my old slide in gas range (Magic Chef- model # 6498XTS with a new slide in gas range and am trying to find out if the new one will fit where the old stove was, here's my problem the...


The installation depths provided in the installation literature, are the minimum requirements for fitting the slide in range into place. You need to determine what the depth of your opening is where you intend to install the appliance. The depth shown on the installation instructions might be showing the overall depth of the appliance, including the oven door, which typically sticks out from the cabinet anywhere from 1-3 inches, depending on the brand, model, etc. The old Magic Chef might have only provided the needed depth for the oven body, and might not have included the front oven door projection, past the countertop, etc. Most cabinents are about 24 inches deep, so anything larger than that, will likely stick out into the room more, unless your cabinents are deeper than 24", you're looking at having the new slide in oven stick out past the front cabinet front/edge, by about 4 5/16". I'd make a cardboard template to the dimensions of the new oven and use that to see just what you're facing with the replacement oven. It could be possible that you've confused the depth with the width for the new oven, as I've not seen many ovens that are as large as 28" unless it was a Viking, or other really high end, professional style oven, etc. Check your installation dimensions again for the Maytag and make a cardboard template to confirm how much space will be needed. The good news is that you can remove the old Magic Chef, since it's not working, to allow you to make a more informed decision as to fit and clearances required for the new oven. Just be sure to disconnect the power to the range or unplug the power cord, if that's what it has, before attempting to remove the slide in. Hope you find this Very Helpful and best regards!

Sep 10, 2009 | Kitchen Ranges

1 Answer

I have a smeg A2-5 oven and have been told it requires a new heating element how easy are these to fit?


Well it is very easy.

First and all diconnect the power cord.
The element secured by two 1/4" screw in the oven.
you have to pull Range out and go, emove the back panel and remove the element wiring connector, and you are ready to replace it with the new one.
Should you need more details please feel free to contact me. I can provide you wiring diagram and instruction booklet.
nguyen@ite.net

Jun 09, 2009 | Smeg A2.5 Dual Fuel (Electric and Gas)...

1 Answer

Oven wont stay alight on new world 110G


Hi - I had this problem too. I assume you are referring to the automatic oven, not the manual one. There is a small 'Licon' switch behind the control knob, which provides electrical power to the main gas valve in the oven. It is activated when the knob is turned on and is also connected to the timer clock, so that power is only provided when the timer reaches the cooking start time, or the timer is not being used. I had this replaced by an engineer from New World (at great expense!). Changing it seemed to be fairly straightforward - the engineer removed the two outermost knobs and unscrewed and removed the facia. The switch is behind the main oven knob - but where you might get one from, I don't know. And don't forget to switch off the power before you try to access the switch, as it is likely to be live.
Good luck
Keith E

Nov 27, 2008 | New World Spirit 110 (Gas) Kitchen Range

2 Answers

The smoke


It is normal for this to happen the first time. Its just the oils from peoples hands who installed the element. It will go away.

Nov 25, 2007 | Hotpoint RGB790SEHSA Gas Kitchen Range

1 Answer

Oven stopped working


replase the oven ignitor it's located nest to the oven burner.

Oct 22, 2007 | New World 60ESO Electric Kitchen Range

Not finding what you are looking for?
New World 55WLg Gas Kitchen Range Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top New World Kitchen Ranges Experts

paulcarew

Level 3 Expert

1875 Answers

John Rodgers
John Rodgers

Level 2 Expert

73 Answers

craig jones

Level 1 Expert

13 Answers

Are you a New World Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...