Question about Tefal UltraGlide Easycord FV4256 Iron

1 Answer

I have burned the iron cable and need to replace the whole cable.where should i take the iron. bought recently from debenhams

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 57 Answers

WHAT I THINK YOU SHOULD DO IS BRING BACK THE IRON TO THE SHOP WERE YOU BOUGHT IT WITH THE RECIEPT I RECKON THE GUARANTEE WOULD NOT COVER THIS YOU MAY HAVE TO PAY FOR THE REPAIR.

Posted on Jul 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why steam iron won't heat up


if there is no light or heat even when the thermostat is switched to the hottest setting then assumption is that the iron is defective.

with the iron not plugged in check the cable and see if it is worn or kinked or cut. look for any burn markings on the plug. if the iron is some years old it may also be that the element has burnt out. this happens more often in areas where water scale is high.


I hope this was useful.

May 12, 2014 | Applica Black And Decker F975 Steam Iron

1 Answer

How to clean inside of iron


Please don't take Landsend advice, as it contadicts this whole "fixya" site! Let's keep it going by not giving in to this throw away world! Some people can't afford a $20 iron @ Wally's!
All the solutions above (besides Landsend) are on it!! Your City water is still too, hard for these delicate, devices. Filtered, as Alan Serna mentioned, is the way to go!! Dump your water out of your iron, when not using-maintenance is key, for everything, even your families!! : ) Have a G8 day!

Sep 28, 2012 | Sunbeam 3017 Iron with Auto Shutoff

1 Answer

Bosch iron TDA76 light comes, on no heat


Hello, welcome to Fixya!

The problem is either from the heating element or a disconnected/loosed wire.

Get a screw driver disassemble the iron and check for any visible wire disconnection or burn. If all wire connection in the iron are intact, then it means the heating element of the iron is defective and needs to be replaced.

Good luck.

Nov 04, 2011 | Irons

1 Answer

When I plugged iron in sparks came out at wall and iron where the cord connects.


Hi,

If you've had this iron for a while it sounds like the cord may be frayed.
switch it off at the wall and unplug it, check the cord for wear, if the insulation is frayed, torn or broken and there are black burn marks on the cord where you saw sparks then the cord needs to be replaced.
DONT plug the iron back in until the cord is replaced.

Otherwise If there are no breaks or black burn marks on the cord, then your power point may be faulty and needs to be replaced!

I hope this was helpful
MobileJB

Jul 13, 2011 | Oreck Cordless Speed JP8100CA Iron

1 Answer

Black rubber burned onto plate of iron


Hi,
Here is a tip that will help you with that problem...

Cleaning a Steam Iron Soleplate
http://www.fixya.com/support/r5301167-cleaning_steam_iron_soleplate

heatman101

Apr 12, 2010 | Black & Decker ProFinish X750 Iron

1 Answer

Suddenly began leaking and overheating, such as too hot for demin but only set of min. Last time this happened I bought a new iron. The new one has been dropped - last year but nothing recently and this...


The iron started leaking from front and back. took iron back to Wal Mart and got another iron and it did the same thing. I cannot use the iron because it is hard to hold the steam almost burn your hands because it leaks a lot all over my cloths . I was so disgusted with the iron until I just put it in the corner and bought another iron from wal mart. I did not know if they would take the iron back , because I had it for a bout (3) months.

Aug 06, 2009 | Rowenta DG-920 Iron

1 Answer

Rowenta won't shut off automatically


Unless you have a 5 or 6 hundred dollar iron, or unless it is brand new, and still under warranty, there is an excellent rule of thumb when an iron quits working: Buy a new one! These days, irons can be purchased cheaply enough that it is WELL worth the money. Not just for the convenience, but for the safety issues. This is an appliance that could burn your house down even if it's in PROPER working order. Hope this helps!!

Chad

Sep 30, 2008 | Rowenta Professional DE880 Iron

1 Answer

My iron bahaves very bad


Izula,
We have had two D2020 Black&Decker Irons that did exactly the same thing. I love the iron...but they have both lasted about 2 months before burning!

Dec 02, 2007 | Black & Decker D2020 Iron

Not finding what you are looking for?
Tefal UltraGlide Easycord FV4256 Iron Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tefal Irons Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Ryan S
Ryan S

Level 2 Expert

328 Answers

Are you a Tefal Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...