Question about GE Profile JP930 Electric Cooktop

1 Answer

GE Cooktop JP930 surface element not working

I've a glass CookTop. One of the burner element (double) no more works. The cricuit breaker trips again and again. Is there some fuse that i can locate to fix this problem.

Posted by on

  • 2 more comments 
  • v_ven Jan 23, 2009

    Two of the burners are putting out decreasing heat

  • trek73 Jan 30, 2009

    I have the same problem. Once the cook top is removed from the counter, how do you remove the glass from the unit?

  • telle11 Apr 03, 2009

    I have similar problems with my dual element.  It 1st started with the heat control knob tighten up and was difficult to adjust.  Then when the stove was off, the indicator light remained on - but it wasn't. It appeared to be shorting out. After sometime all four "element on" lights remained on even though there was no heat.  WOULD APPRECIATE ANY SUGGESTIONS TO HELP ME FIX THIS PROBLEM.

  • Anonymous Mar 27, 2014

    I would just like to find out if there is some sort of reset switch.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 161 Answers

It sounds like the burner needs to be replaced. When they burn out sometimes they short out to ground. The cooktop will have to be removed from the counter and the glass top opened. You will probably be able to see where the element is burned out. Replace it and you should be fine. If it is too expensive to fix just disconnect the wires to the burner where they attach to the control . Then you can use the remaining burners. I really don't know what a replacement burner costs. An open coil is around $30.

Posted on Jul 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pot stuck to cooktop


Did you find that it was stuck after it had cooled off? A vacuum was probably created between the pot and the glass top. You could try twisting the pot, leaving it for a while, or heating it up again.

Apr 11, 2010 | GE Profile JP930 Electric Cooktop

1 Answer

GE Profile glass top cooktop- burners do not heat, indicator lights do work


If none of the burners are working but the pilot light does you are having a power problem and only getting 120 volts to it. Check the breakers to make sure they are on correctly. 240 volts is needed to operate the cooktop. Hope this helps. Rick

Mar 09, 2010 | GE Cooktops

1 Answer

One of the burners does not work. Is it possible


yes,heating elemnt and the control can be chgd.to chg those pull the unit out and let it sit on the counter.remove all the screws around the stove just below the glass top.once the screws are out u can pull the top up and have access to all the components.make sure to turn the ckt breaker off b4 opening.u dont have to disconnesct the power cord from the wall if it is hard wired.

Aug 09, 2009 | GE Profile JP930 Electric Cooktop

1 Answer

Radiant cooktop blew a fuse?


Call the service tech it;s under warranty and, this model is notorious for this fault

Apr 21, 2009 | General Electric 36 in. Profile PP962...

1 Answer

Electric Glass GE Profile Cooktop Burner popping


yes the knob is attached to a switch and the switch to the burner by way of wires..you can get into the cook top.but with your description of whats going on i would have the switch with me and then may only have too take apart once.there is a chance your burner is bad,but as you describe the way the switch is acting is seems pretty sure just the switch.you can order switch on line you need your model and ser#

Jan 30, 2009 | GE Profile JGP636 Gas Cooktop

1 Answer

Tripping breaker


Replace the burner and receptacle and you should be short free. You may also need to replace the surface element switch too if it doesn't come on at all or stays on high regardless off knob setting.

Dec 16, 2008 | Jenn-Air JED8430 Electric Cooktop

1 Answer

Dual Surface Selector Switch


more common is the dual switch to be bad, but it is possible that the elemnt itself has burnt out, usually a 5 yr warr on the elemnts under glass

Nov 08, 2008 | GE Profile JP930 Electric Cooktop

2 Answers

Ge profile electric counter top stove


I did not receive instructions with my G E Profile cook top Model No. 80030750434). There is a build up on the elements which I am having problems removing. Should the top be scraped while the stove is hot or cold? What is the best cleaning product to use?

May 01, 2008 | GE Profile JP930 Electric Cooktop

Not finding what you are looking for?
GE Profile JP930 Electric Cooktop Logo

946 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Cooktops Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

meztang
meztang

Level 2 Expert

112 Answers

Are you a GE Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...