Question about Gateway Wireless-B Router (wbr-100)

1 Answer

192.168.1.1 Won't connect - Have Windows Vista SP1

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Salw ih kany center iarq

Posted on Jul 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

VALIDATING IDENTITY


I've also had this problem when trying to connect my Medion Laptop through a Netgear Range Extender. It would find the router wirelessly but not through the Netgear. I had tried every solution on the web for days without success. Thanks to this page and a contributor who suggested updating the driver (which I had thought of previously) I did that and it all works fine. My laptop is 7 years old and wouldn't recogise WPA-PSK which was the setting on a newly installed router.

Update your Driver. :)

May 26, 2010 | Linksys WRT160N Wireless Router

Tip

Installing Drivers For Windows 7


For Belkin Adapters Only F5D 7050 Has windows 7 drivers on the website

For other Models

Download the Drivers For windows Vista

Right click on the downloaded file

Click on the compatibility Tab

Select Run this program in compatibility mode for Vista SP1

Click Apply , then OK

Now install the File


on Jan 13, 2010 | Routers

1 Answer

Change my settings from wep to wpa I have a belkin 54g


when you change the wireless security on the router , it is recommended tht you will change the wireless network name also ( SSID ). Because when you try to connect to the wireless network on the computer, your computer will try to connect to the same old network name with the old wireless security settings. To avoid this you can change the wireless network name. WPA is supported by windows XP SP2 and above operating system.
If the operating system on your computer WINDOWS XP SP1 and if you are trying to connect using the windows utility then you would not be able to connect to the network .

Click Here for more information about the routers and networking

Jan 28, 2010 | Gateway Belkin 54g Wireless DSL/Cable...

1 Answer

I'm being disconnected when downloading large files or using Microsoft Update. Win Vista SP1 Speedstream 5660 Linksys WRT160N Verizon DSL Once I disconnect the modem for 4 minutes and connect it again I...


Access the GUI of the router and lower down the MTU settings. By default the MTU is 1500 so try to lower it down to 1492 or 1400. Make sure that the firmware is upgraded as well.

Jul 11, 2009 | Efficient Networks SpeedStream 5660 Router

1 Answer

Wireless shows connection,but will not connect.


This kind of problem occur due to dhcp disable in the wireless router for the security purpose. So try to give the ip adress manually by right clicking on the wireless and give the ip adress of the same range in which your network in working e.g 192.168.1.0 is the range of your ip addresses so please select the ip which is not been used by any other computer and than in default gateway enter the ip address of you wireless router and you will be able to access the internet on your system.

Dec 01, 2008 | Linksys Wireless-G WRT54GS Router...

1 Answer

I am trying to set up security for my lynksis.  Currently it is unsecured. I was following directions then lost interent connection.  When I tried to use the ISP of 192.168.1.100 nothing happens.  I just...


Hi!
To access the router's web interface for configuration, you need a PC that's physically connected to the router (ethernet connection). Follow these steps:

Step 1 Open your Internet browser and type the IP address of the router in the address bar (http://192.168.1.1) . The default IP address is 192.168.1.1 . At the login, leave the username blank and type your password (default password is admin). Click the OK button.

Step 2 To setup security, Click the Wireless tab > then select Wireless Security (right below the Wireless tab).

Step 3 Under Wireless Security, you can either select WEP or WPA for wireless security.

When selecting WEP 64 bits: (for windows XP SP1 to Vista)

Look for Key 1 box - type a 10 hexadecimal password (meaning letters A to F or numbers 0 to 9 only). Example: ABC1234567 or 985D8A8F04 .

When selecting WEP 128 bits (for XP SP2 to Vista)

Look for Key 1 box - type a 26 character Hexadecimal code.

When selecting WPA PErsonal: (XP SP2 to Vista)

Look for a passphrase box - type a password at least 8 characters (numbers or letters).

Please DO NOT FORGET the password that you set - you will need this for wireless connection.

Click Save settings.

I hope that helps!

Good luck and have a nice day!

Dec 01, 2008 | Linksys Wireless-G WRT54G Router

1 Answer

Vista and remote printing


Have you applied SP1 to Vista? It is supposed to fix a plethora of issues.

Oct 24, 2008 | NetGear DG834G Router

1 Answer

Online web configuration


For the DI-704P (Revision B) you will need to download and install the Java Plug-in for your Operating System. To download and install the Java Plug in now click the link below. Windows XP, Me, NT, 2000, 98, or 95 and Internet Explorer - http://java.com/en/download/index.jsp An alternative is to upgrade your browser to the following: Internet Explorer 5.5 or higher (with SP1) Internet Explorer 5.x (Mac) Netscape 6.0 or higher Mozilla 1.2.1 (5.0) or higher Firefox 0.8 or higher Opera 6.0 or higher Safari (with Java 1.3.1 or higher) Camino 0.7 or higher

Feb 16, 2006 | D-Link DI-704P Router

Not finding what you are looking for?
Gateway Wireless-B Router (wbr-100) Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gateway Routers Experts

Steve

Level 3 Expert

3287 Answers

k24674

Level 3 Expert

7987 Answers

Justin
Justin

Level 3 Expert

2072 Answers

Are you a Gateway Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...