Question about Razor E300s Electric Scooter With Seat

1 Answer

I ride my scooter and then it turns off..the button pops out and when I push it back in it will work for a few moments then stop again.. is the battery done?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 22 Answers

I posted a simliar question. I ended up taking my scooter to a battery store that is licensed to work on razor scooters. They ulitmately concluded the wires to the popup fuse itself were loose. They replaced the popup fuse as well just incase. I have now been using the scooter without the fuse popping every 50-100 feet.

Posted on Oct 30, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pride Celebrity X mobility scooter just clicks when throttle is engaged. Green light flashes 4 times. What is wrong?


Hi again try this remove key & push freewheel lever into freewheel then push it into drive put key back & hope the control box has reset...PLUS CHECK THE BATTERIES WITH A LOAD TESTER available on E/Bay cost aprox $35 dollars .. flash code ( CURRENT LIMIT TIME OUT ) TURN SCOOTER OFF FOR A FEW MINUTES THEN TURN IT BACK ON ... cheers

be54b311-20fe-472c-b58c-f629dadd494f.jpg

Nov 25, 2017 | Pride Health & Beauty

1 Answer

When I turn it on an alarm sounds and won't stop. The scooter works well except alarm won't stop. It is as if you are pushing on the horn all the time.


hi Irene, sounds like you got water inside the button you push to activate the horn, the push button will need be dried out ....either by disassembly's or carefully placing a warm setting hair-dryer near the button and operate to get the water to evaporate .. but don't do it too hot otherwise the button will start to melt...
Regards
Rob

Apr 05, 2016 | Pride Go-Go Sport 3-Wheel Scooter

1 Answer

Where is the reset button on my scooter


hi, if memory serves me right it located under your feet ..

gently push it in...if you felt like you were pushing something back in , then it has popped otherwise no,.,..

Regards
Rob

Feb 06, 2016 | Mercury Regatta 8mph Road Mobility Scooter

1 Answer

Mobility scooter stops dead. I turn key off and back on it will go again then stop


Check your battery terminals are tight. It sounds as though they have come loose, or you didn't do them tight enough when you changed batteries. Perhaps clean the terminals both on the leads and the batteries, and finish with a wipe of Vaseline to keep water at bay. Good luck.

Dec 02, 2014 | Motorcycles

1 Answer

Why does my 2009 diamo velocity 50cc scooter lose power under load?


Hi, Integrattype your muffler may be clogged for more information about your question and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
My scooter loses power after riding awhile
Randomly losing power slowing down Provoscooter com Forums
http://www.carlsalter.com/diamo-service-manuals.asp
Scooter Parts for Chinese Scooters Atvs
Chinese ATV Owners Repair Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Aug 17, 2012 | 2009 Diamo Velocity 50

1 Answer

Have the phoenix s35015 scooter. The battery is charged, put it in the scooter and turn key. All power lights up to the green, lightsheadlight can come on and horn beeps when pushed. The red light does...


make sure you put it in "gear" completely sometime you can get it almost locked but its still in freewheel, flashing light is error code, do a count of blinks and stops, look in the back of book for trouble codes

Oct 01, 2017 | Drive Medical S35015 Phoenixcompact...

1 Answer

Cancel printing is on and will not turn off after canceling when pushing the stop/exit button. i cannot print anything else. when i turn it off and unplug it then plug it back in for 1 min and turn it back...


You did not list your model but if it is an MFC series then try turning off the machine and then hold down the clear/stop button while turning the power back on. Continue holding the button for a few seconds. This procedure will clear whatever may be stuck in memory. This works on most Brother models but may not work on yours.
Good Luck and Thank You for using Fixya.

Aug 12, 2010 | Brother Office Equipment & Supplies

1 Answer

The motor or transaxil lock up and stop the


Hi. Sounds like the circuit breaker ( over load switch ) is tripping out. If you let it sit for a few minutes, does it start to work again? Does it stop when you are driving onthe flat ground, or when you drive up a slope.
I have had cases where this happens to scooters going up a slope, usually because the circuit breaker is rated to low. Sometimes a faulty or burn't out motor will cause this fault.

Also check that the brake solenoid ( free-wheel )is releasing properly. Can you push the scooter when the brake is released?
Good luck. Neil.

May 31, 2010 | RTO Mega Motion 3 Wheel Travel Pal Scooter

1 Answer

I have a ctm scooter the battries are charged fully when i switch on the scooter will not work switch off and on again it then will travel a few feet before stopping


I would say the throttle pot is slightly out of neutral allowing the scooter to travel slightly when turned on. Try moving the throttle lever slightly in the opposite direction to which the scooter is travelling (i.e. if the scooter moves forward when turned on, press the lever to go backwards, but only a small amount). If the scooter stops and you hear a clicking noise from the back of the scooter (this would be the brake clicking on) then that would be your problem. Would just need a small adjustment but best left to a dealer as it has to be sopt on! Sometimes scooters will not work if the throttle is slightly out but if its only a very small amount out of neutral, it might sometimes work in the manner you have suggested. We have come accross this fault on a few occasions. Hope this helps...

Mar 07, 2010 | Health & Beauty

1 Answer

Freezes up while operating


I have found that my aiptek digital camcorder also freezes like this sometimes after I have pressed the button to stop recording a movie. You are right that sometimes you must remove the battery to unfreeze it, but I have found a couple of other tricks that work sometimes.

1. You can hold down the menu button for a few seconds (like 6). Sometimes this kicks it into the menu and unfreezes it.

2. Sometimes using the power button inside of where the screen stores to turn it on and then off again often helps.

3. Popping the digital card out (push in so it unlocks, then push it right back in) also helps unfreeze it for me.

If those don't work, pop the battery out again.

I do find that every few months I need to clean the connection points on both my battery and the camera where the battery clicks in. After I do this it behaves much better for a couple months. Good luck.

Mar 28, 2009 | Aiptek MPVR Digital Camera

Not finding what you are looking for?
Razor E300s  Electric Scooter With Seat Logo

Related Topics:

410 people viewed this question

Ask a Question

Usually answered in minutes!

Top Razor Toys Experts

Bryan Mcphee
Bryan Mcphee

Level 1 Expert

36 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

William Erickson

Level 2 Expert

47 Answers

Are you a Razor Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...