Question about GE Profile PSW26P Stainless Steel Side by Side Refrigerator

3 Answers

Water filter replaced button not working - GE Profile PSW26P Stainless Steel Side by Side Refrigerator

Posted by on

  • Anonymous Oct 01, 2008

    can't find the "filter replaced" button. this is the botton you are supposed to press once you replace the filter. still not getting it.

  • Anonymous Oct 03, 2008

    I have the exact same problem. The fridge would not reset following the factory instructions. I unplugged the fridge for about 30 seconds, and when I plugged it back in the LCD water percent was back to 0%. Nice, because I wasn’t looking forward to a service call.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just press the water and lock buttons at the asme time for 5 seconds.

Posted on Feb 19, 2009

I have. didn't work as the button disappears and the beverage center text overwrites it.

Posted on Oct 01, 2008

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 74 Answers

Hold it down for 3-5 seconds to reset it

Posted on Aug 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have GE profile refrigerator with bottom freezer the indicator light to replace the water filter came on I did so but it will not pump out water I held the reset button for 3 seconds still nothing


Double check the filter install you did. Make sure there isn't any clear plastic seal over the center hole of the filter and retry the water. If it worked before the problem has to be in the filter install or the filter is possibly defective and wasn't manufactured properly. The reset button is only for the warning light---has nothing to do with filter or water operation.

Apr 10, 2015 | GE Refrigerators

Tip

How to Reset Your Water Filter Light


<b>Amana:<br /></b> <ol> <li>Press and hold the <b>dispenser lock</b> and <b>auto light</b> buttons on the dispenser for 4 seconds until the filter status indicator begins to flash, then release the buttons.</li></ol>or<br /> <ol> <li>Press and hold the <b>dispenser lock</b> and <b>water</b> buttons for 4 seconds until the filter status indicator begins to flash, then release the buttons.</li></ol>or<br /> <ol> <li>After replacing the water filter, press and hold the Reset Filter pad for 3 seconds. The Order and Replace indicator lights will blink and then go off when the system is reset.</li></ol><span style="font-weight: bold;">Brita:</span><br /> <ol> <li>Press firmly and hold start button for 5 to 10 seconds.</li> <li>Four bars will appear in the display, one after the other, and flash. Do not release the start button until the 4 bars appear and start to flash. If you have difficulty pressing the start button, a capped ballpoint pen may be used to press the button down.</li> <li>A small flashing dot in the lower right corner shows the indicator is working.</li> <li>Every 2 weeks a bar automatically disappears. When only 1 bar remains make sure you have a new filter on hand.</li> <li>After 2 months, when all bars have disappeared, an arrow will flash at the top of the display reminding you to change your filter. </li></ol><b>Frigidaire<br /></b> <ol> <li>Press and hold the <b>reset </b>button on the dispenser until the green light flashes (up to 15 seconds).</li></ol><b>GE:<br /></b> <ol> <li><b>P</b>ress and hold the <b>reset water filter</b> button on the dispenser for 3 seconds.</li></ol>or<br /> <ol> <li> Press the reset button on the dispenser for 4 to 8 seconds then release. </li></ol><b>Hotpoint:<br /> </b> <ol> <li><b>P</b>ress and hold the <b>reset water filter</b> button on the dispenser for 3 seconds.</li></ol> <b>Jenn-Air:<br /> </b> <ol> <li>Press and hold the <b>lock</b> and <b>light</b> buttons (<b>lock and water</b> on newer fridges) on the dispenser for about 4 seconds, until the indicator light blinks.</li></ol><b>Kenmore:<br /></b> <ol> <li>Press and hold the button next to the filter light for 10 seconds.</li></ol><b>KitchenAide</b>:<br /> <ol> <li>Press the <b>light</b> switch 5 times within 10 seconds. If the fridge has a <b>filter button</b>, press and hold it for 5-10 seconds.</li></ol><b>LG:<br /> </b> <ol> <li>Press and hold the <b>reset</b> button for 3 seconds.</li></ol><b>Magic Chef</b> <br /> <ol> <li> Press and hold the light and lock pads until the change filter light flashes. (approximately 3 seconds)</li></ol> <b>Maytag:<br /></b> <ol> <li>Press and hold the <b>lock</b> and <b>light</b> buttons (<b>lock and water</b> on newer fridges) on the dispenser for about 4 seconds, until the indicator light blinks.</li></ol>or<br /> <ol> <li>Press the refrigerator's light switch five times within ten seconds.</li></ol><b>Samsung:<br /> </b> <ol> <li>Press the <b>ice type</b> and <b>child lock</b> buttons simultaneously for 3 seconds. NOTE: Hold the buttons for only 3 seconds. If you press these 2 buttons simultaneously for 5 seconds, the reset function ceases.</li> <li>Release the buttons and repeat the same step one more time. The water filter indicator light should turn green.</li></ol>or<br /> <ol> <li><span>Press and hold the "Alarm/Hold" button for 3 seconds.</span></li></ol>or<br /> <ol> <li><span>Press and hold the <i>Fridge </i>and <i>Power Cool</i> buttons for 3 seconds.</span></li></ol><b>Whirlpool</b>:<br /> <ol> <li>Press the <b>light</b> switch 5 times within 10 seconds. If the fridge has a <b>filter button</b>, press and hold it for 5-10 seconds.</li></ol>

on Jun 17, 2011 | Refrigerators

1 Answer

I've got a side by side Whirlpool refridgerator. The Water Filter status light is not indicating. What could be the problem and solution?


There are several pages that explain dispenser programming. This is on page 10 of the owners manual.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change

your water filter. When the water filter status display changes from

"GOOD" to "ORDER," this tells you that it is almost time to

change the water filter cartridge. Replace the water filter cartridge

when the water filter status display changes to "REPLACE." If

water flow to your water dispenser or ice maker decreases

noticeably, change the filter sooner. The filter should be replaced

at least every 6 months depending on your water quality and

usage.

After changing the water filter, reset the status light by pressing

and holding the FILTER button for 3 seconds. The status light will
change from "REPLACE" to "GOOD" when the system is reset.

Changing the Water Filter

1. Press the eject button to release the filter from the base grille.

2. Pull the filter straight out.

3. Turn the cap counterclockwise to remove it from the filter.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

4. Align the ridge on the cap with the arrow on the new filter and

turn the cap until it snaps into place.

NOTE: You can run the dispenser without a filter. Your water

will not be filtered. Simply insert the cap all of the way into the

base grille and rotate the cap until it is firmly in place.

5. Remove the covers from the O-rings. Be sure the O-rings are

still in place after the covers are removed.

6. Push the filter into the base grille. The eject button will pop

back out when the filter is fully engaged.
7. Flush the water system. See "Water and Ice Dispensers."

Water Filter Status Light:

The water filter status light will help you know when to change your water filter.

When the dispenser control panel's water filter status display changes to "ORDER," this tells

you that it is almost time to change the water filter cartridge.

Replace the water filter cartridge when the water filter status display changes to "REPLACE."

The filter should be replaced at least every 6 months depending on your water quality and usage.

NOTE: If water flow to your water dispenser or ice maker decreases noticeably, change the

filter sooner. After changing the water filter, reset the status light.

Details:

Pressing and holding RESET FILTER starts the 3 seconds countdown. Using the dispenser

cancels the countdown AND no dispensing is permitted. The number '3' blinks 3 times and the

'invalid' tone sounds 3 times and user has to release both the pad and the button and press

the button again to start it over

After 3 seconds, the BLUE WATER BARS in the Icon flash and an audible tone sounds 3
times. When the system is reset, the "ORDER" and "REPLACE" icons will disappear from the

display screen. See figure 16.
Note: Users can reset the filter status at any stage.

sea_breeze_131.jpg

If you should need the complete and exact model number and manual with parts manual you will need to enter the Model Number here=> sea_breeze_132.jpg Manuals, Guides and Instructions Please rate this solution, Thanks, Sea Breeze
User manual click HERE

Apr 02, 2011 | Whirlpool 25.6 cu. ft. Side-by-Side...

1 Answer

I changed the water filter and now the water is not working


For LG LSC26905:

If you replaced the water filter cartridge on the dispenser due to a filter replacement indicator appeared on the display, press and hold the lock button more than 3 seconds to reset the filter timer.

Make sure the water supply line is open.

Nov 07, 2009 | LG LSC26905TT Side by Side Refrigerator

1 Answer

The warning light to reset filter came on. I've


Resetting your Refrigerator filter indicator light after changing your water filter Some people are not aware that after you change your refrigerator water filter, there are two more steps that should be taken to complete the water filter change process.
Step 1:
Reset your water filter indicator light - Most new refrigerators come equiped with an indicator light that notifies you when it is time to change your water filter. This light does not automatically reset when you change your water filter. Here is a list of refrigerator manufacturers and how to reset the indicator light.
Amana Refrigerators - Press and hold the Auto and Dispenser Lock buttons until the water filter status indicator light flashes.
Frigidaire Refrigerators - Press and Hold the Reset Button Until the Indicator Light Flashes.
GE General Electric Refrigerators - Press and Hold the Reset Button for around 8 Seconds.
HotPoint Refrigerators - Press and Hold the Reset Button for around 8 Seconds.
Jenn-Air Refrigerators - Press and Hold The Light and Lock Buttons until the Water Filter light flashes.
Kitchen Aid Refrigerators - Press and Release the Light Button 5 times Quickly.
Maytag Refrigerators - Press and Hold The Light and Lock Buttons until the Water Filter light flashes.
Samsung Refrigerators - Press and Hold the Ice Type and Child Lock Buttons at the same time for 3 seconds.
Whirlpool Refrigerators - Press and Release the Light Button 5 times Quickly.
Step 2:
Flush a couple of gallons of water through your new filter. Since most refrigerator water filters are made of carbon, some carbon residue is present in the first gallon or two of water. This will leave a bitter taste and residue in your water. If you continue to have these problems after flushing a couple of gallons through the filter, it is possible that you have a defective water filter.
Once these two steps are completed, you are all set to enjoy great tasting ice and water through your refrigerator. If you don't see your manufacturer listed or the insructions don't work for your model please post a comment with your make and model number so that we can provide exact instructions for your model.

May 06, 2009 | GE PDS22LBN Bottom Freezer French Door...

1 Answer

Water filter does not eject when button is depressed.


I just had the same ting happen to me. You need to leave the cover to the water filter (it is the black plastic cover that is part of the grill) is still connected to the filter. After depressing the eject button, this cap helps to pull out the filter. DON'T throw away this very important part, other wise it is impossible to get the filter out. Once you eject the filter, some water will leak from the filter. Just put it in the sink to drain for a while. 

Apr 27, 2009 | KitchenAid Superba Architect KSCS25INSS...

1 Answer

Auto Water Dispenser


that maachine shoulnt work with out the filter inplace, all i can suggest is replacing the filter.

Mar 18, 2008 | Frigidaire FRS3R5EMB Side by Side...

1 Answer

Filter light still on "Red"


try holding ice type and child lock together for 3 seconds that worked on mine

Mar 30, 2007 | Maytag MSD2454G Side by Side Refrigerator

1 Answer

No ice or water from dispenser


Kathryn, make sure you do not have the dispenser locked out. Press and hold the lock button for 3 seconds. If you have a green light above the pad this indicates lock. You are going to have to hold the water lever for a while until all the air in the new filter is purged. Catriver...post back.

Nov 12, 2006 | Amana ARS9265B Side by Side Refrigerator

Not finding what you are looking for?
GE Profile PSW26P Stainless Steel Side by Side Refrigerator Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

Vish Iyer
Vish Iyer

Level 2 Expert

74 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...