Question about Philips 60PP9202 60" Rear Projection HDTV-Ready Television

1 Answer

Have phillips 55 hdtv that needs convergence badly

Can you help....its phillips dptv310 or model 55pp935217

Posted by on

  • 2 more comments 
  • Anonymous Oct 19, 2008

    convergance cant be adjusted



  • Anonymous Nov 29, 2008

    My Red CRT is unable to be manually converged, to far out of allignment on upper left mostly. My model is 55PP935212.

  • Anonymous Feb 10, 2009

    i have the same problem but im new to this what are IC,s, where are they and where are the resistors? also when i go in to adjust point by point now the red will not move at all? (disturbedindestructable@hotmail.com)

  • msaltar Apr 19, 2009


    Hey...I experienced the same problem here. However, I have no knowledge or certification in repair...just trying to see whether you think it's worth it to try and pay someone to do the fixes you recommended, or is it just time for another TV?



×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 230 Answers

OK, friends.. Replace two Ic's Stk 392-110, and get in service menu settings , and adjust point by point. After replaced stk IC's, check if any resistor look brown or born, if yes, replaced it with 6.8 Ohms.SOme time SSB is defective ( small signal board, replaced it ) If you have questions? noetvs@embarqmail.com . Good Luck !!

Posted on Jul 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a big magnavox tv that all of a sudden the picture went out with only sound. I tried everything possible from changing cables and calling my cable company to see if the problem was there but no


Your flyback has failed most likely...bad new is they are nearly impossible to find, This is a known issue on most of the models below. The site Tv Repair Kits can sometimes get replacements - but its not often.

This repair kit is known to work on Magnavox TV sets with the following Chassis/Model Numbers.

DPTV305 , DPTV305F , DPTV310 , DPTV315 , DPTV330 , DPTV330F , DPTV335 , DPTV340 , DPTV345, MAG01

Model Numbers

( 43PP9202/17 43PP920217 43PP9202/17F 43PP9202/84 43PP920217F 43PP920284 43PP920201 43PP920284F 46PP9302/17 46PP930217 46PP930201 46PP930217F 46PP930284 46PP930284F 46PP9302H17 50PP9202/01 50PP9202/17 50PP9202/84 50PP9202/84F 50PP920201 50PP920217 50PP920284 50PP920284F 50PP920217F 51MP392H/17 51MP3964H/17 51PP9303H/17 51PP9363H17 51PW9303/17F 51PW936317F 55PP9352/17 50PP920217F 51MP392H17 51MP3964H17 51PP9303H17 51PP9363H17 51PW930317F 55PP935217 55PP935201 55PP9363H17 55PP9502/84 55PP950284 55PP950201 55PP950217 55PW936317F 55PW9383/17F 55RW9515/35 60PP9202/17 55PW938317F 55RW951535 60PP920217 60PP920201 60PP920217F 60PP9352/17 60PP935217 60PP935201 60PP9363H17 60PP938317F 60PP9502/17 60PP950217 60PP950201 60PW936317F 60PW938317F 43PP9202/17 43PP9202/17F 43PP9202/84 43PP920217 43PP920217F 43PP920284 43PP920201 43PP920284F 46PP9302/17 46PP930217 46PP930201 46PP930217F 46PP930284 46PP930284F 46PP9302H17 50PP9202/01 50PP9202/17 50PP9202/84 50PP9202/84F 50PP920217F 51PP9303H/17 51PP9363H17 51PW9303/17F 50PP920201 50PP920217 50PP920284 50PP920284F 51PP9303H17 51PW930317F 51PW936317F 55PP9352/17 55PP935217 55PP935201 55PP9363H17 55PP9502/84 55PP950284 55PP950201 55PP950217 55PW936317F 55PW9383/17F 55RW9515/35 60PP9202/17 55PW938317F 55RW951535 60PP920217 60PP920201 60PP920217F 60PP9352/17 60PP935217 60PP935201 60PP9363H17 60PP938317F 60PP9502/17 60PP950217 60PP950201 60PW936317F )

Mar 29, 2012 | Philips Projection Televisions

1 Answer

Model 55PP935217 multiple convergence mode, the blue colored + is pulsing after IC chips #7044 and #7045 were properly replaced and resistors (12) were good. When single convergence mode is selected, the...


I understand your frustrations, and if you did the work yourself you can feel really bad. In this case if you really want to save this TV, I would suggest you visit Union Electronics. And purchase a reworked replacement board. In many cases this is the best route to go and the price is reasonable. Call them at 1 800 648 6657. I have had very good luck with this company! And these boards are guaranteed, ask for the lenghth allowed. Have your TV model # and tell them you are looking for the convergence board. Thanks for asking!

Aug 08, 2010 | Philips 55PP9352 55" Projection Television

1 Answer

How difficult is to replace convergence chips on a PHILLIPS model 55pp935217


quite difficult it not just replacing the chips you have to test the resistor in front of the chips which mean you have desolder 1 end of the resistor so you get a proper reading on the mulitmeter also you have to test the capacitor at either end i've repaired a few . trust me if i was you get a quote from an engineer good luck

regards
shaun

Mar 30, 2010 | Philips 60PP9202 60" Rear Projection...

1 Answer

Picture looks like its red and green 3-d,Phillips 55pp935217


Ur convergence it dead,Need a convergence kit,use what in that kit,Know how to solder righht?Tries Tv Repair World.com,Ebay.com.

Oct 06, 2009 | Philips 55PP9363 55" Rear Projection...

1 Answer

Phillips hd tv


convergence i.c.s change both of them even if only one color is out. if one is bad the other is usually going to give out soon. the part # should be. stk 392-120. also check resistors around i.c.s if the open you wont be able to adjust convergence.

Mar 20, 2009 | Philips 55PP9352 55" Projection Television

1 Answer

Phillips tv , double vision,


You have bad convergence IC's. Replace both the red and blue drive chips. They are easy to spot. They are mounted to large, finned heat sinks. The # on the chips starts with "STK-" and then there are numbers following. Both red and blue use the same part. There are 20 or so pins to unsolder\solder. These parts are available to the consumer from tritronicsinc.com. Good Luck!!

barneyluc

Oct 03, 2008 | RCA R52WH73 Projection Television

1 Answer

Philips 55" hdtv rear projection internal parts


If your model number is 55PP935217 you dont have a ballast. You have a rear projection with 3 CRts . Please let me know if thats the correct model number and what your symptons are. I will be able to help you get what ever part youre needing.

May 22, 2008 | Philips 55PP9352 55" Projection Television

2 Answers

55pp935217 Way too much blue


No sounds like the blue CRTs coolant has congealed and thats whats giving you the trouble. the blue tube get congealed and will cause the blue to not even show up properly in the convergence menu

May 18, 2008 | Philips 55PP9352 55" Projection Television

3 Answers

55 hdtv philips having issues with blue and red lines around everything ......


change the convergence ICs also check the resistors right next to the ICs as 1 or 2 of them may be open as well.

Mar 28, 2008 | Philips 55PP9352 55" Projection Television

Not finding what you are looking for?
Philips 60PP9202 60" Rear Projection HDTV-Ready Television Logo

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68408 Answers

Are you a Philips Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...