Question about Whirlpool Duet GHW9150P Front Load Washer

5 Answers

Control locked on ghw920 can u help me unlock

Same

Posted by on

  • 8 more comments 
  • Anonymous Oct 07, 2008

    My washing machine has a red light open to control lock, and I can't put off, so I can do anything

  • Anonymous Oct 07, 2008

    kenmore elite he3 front load washer

    the control lock light is open red.I can't put off and I can't do anything



    thank you

  • martine1972 Oct 07, 2008

    kenore elite he3 front load washer

    the control lock light is red. I can't put off so I can't do anything with, how could I put off this lock

    thank you

  • Anonymous Oct 11, 2008

    my washer's controls locked? i've tried everything that i can think of to unlock the controls but nothing works.

  • JRSMITH2447 Oct 21, 2008

    MY CONTROL LIGHT IS ALSO STAYING ON I CAN OPEN THE DOOR BUT NOT ABLE TO CLEAR THE CONTROL LOCK NOR START ANY LOADS . I HAVE UPLUGED TO TRY AND RESET BUT THIS STILL WON'T RESET WHAT CAN I DO TO RESET

  • ingarussell Oct 31, 2008

    ccontrol lock light is on but dryer wont turn on

  • Anonymous Jan 25, 2009

    control locked what do i do to reset

  • Anonymous Jan 28, 2009

    The control lock light is on and I have tried holding down the End of Cycle Signal and that did not work..any suggestions?

  • ssalazar Mar 13, 2009

    We tried everything and it will not turn off. We unpluged it held the end cycle button down for 3, 5, 10 and even more seconds and it will not work. Now what sould we do.

  • abolduc264 Apr 22, 2009

    My control light is on as well, I have tried everything Is there a solution?

×

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Press and hold the End of Cycle Signal button for three seconds. This will turn off the Control Lock feature.

Posted on Dec 05, 2008

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 9 Answers

For the washer, hold the End of Cycle button for 5 seconds. For the dryer, press "More time", "Less time", "More time", "Less time" buttons in that sequence within 5 seconds.

Posted on Mar 11, 2009

  • kellie0217 Dec 01, 2010

    Thank you, thank you, THANK YOU!!! : )

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Thank you!!! That worked!!

Posted on Feb 13, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Washer controls locked Whirlpool duet GHW 9200

Posted on Aug 10, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My control locked light is on and wont turn off and the dryer wont start

Posted on Oct 31, 2008

2 Suggested Answers

aborcass
  • 2651 Answers

SOURCE: control locked on ghw920 can u help me unlock

theres abutton off the end of the control panle( youll need to lok closely) but marked "control lock hold for 3 secs"

Posted on Mar 04, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the fuses for the power dock locks on a 2006 montecarlo06ss


DR/LCK fuse 25 amp . located in the I/P block
Fuse Block - I/P
In the right front kick panel

Power Door Locks System Components
The power lock system consists of the following components:
• Body control module (BCM)
• Driver door lock cylinder switch
• Front passenger door lock cylinder switch
• Driver door lock switch
• Front passenger door lock switch
• Door lock actuators in each of the doors
• DR LK Fuse 20-amp
Door Lock System Controls
The Power Door Lock System is controlled by the body control module (BCM) and can be activated by any one of the following:
• A door lock switch lock or unlock actuation
• A door lock cylinder switch unlock actuation
• A keyless entry transmitter actuation
• An automatic door lock actuation (Personalization function)
• An automatic door unlock actuation (Personalization function)
Door Lock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the lock position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the lock position.
Driver Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the left front (LF) door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked separate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed).

Mar 23, 2017 | 2006 Chevrolet Monte Carlo

Tip

The front light lit on my Whirlpool dryer is showing control locked


Hi.

If the front light lit is control locked, that means that your Whirlpool electric dryer had been set in control lock mode.

Control lock is a special mode that will prevent user from changing settings or using control until the dryer gets unlocked again.

The machine is set to control lock mode by holding down the CONTROL LOCK/UNLOCK button for several seconds. In the same way you can stop the control lock mode when the machine is already set to Control Lock.


When the dryer is running and Control Locked is on, the dryer can still be stopped by pressing the Pause/Cancel button, but cannot be restarted until the control is unlocked.

If the front light lit is control locked but the dryer door opens and it does not turn off, then you are probably in this situation. In that case, the door will be opening , but the machine still stays locked.

Disconnecting the machine from power, either unplugging power cord or tripping circuit breaker, won't help. The control lock system is designed to stay on in case of power failure.
If the machine is control locked, try unlocking it with the following procedure.

To unlock: Press and hold the CONTROL LOCK/UNLOCK button for 3 to 5 seconds to turn the control lock feature off.

If that does not work, try disconnecting power for five minutes to reset the machine, and eventually do unlock again. As said, cutting power alone will not cause the machine to unlock.


If the machine is still not responding, the lights stay on all the time, the dryer panel does not respond to control unlock procedure, and the door does not lock anymore, then it may be a defective control board.

If you are in this situation, before replacing the control board more parts, including the door lock must be tested. In that case the best option may be contacting the Whirlpool support number listed on the Dryer use and care manual, usually in the last pages.

In this case try resetting control lock as explained above, as told the dryer is more likely control locked and then stopped.


Regards.

Ginko.

on Feb 01, 2010 | Whirlpool GEW9250 Electric Dryer

1 Answer

2005 Buick Rendezvous you can hear the relay clicking but the door locks will not open and close


Check for broke wires inside the boot from body to driver door , this is a common problem . If you don't find broke wire's , pull the door panel to get at driver door switch . Check for voltage an ground circuit .
Rendezvous Door Lock System Components
The power door lock system consists of the following components:
?€¢
Body control module (BCM)


?€¢
Driver door lock switch


?€¢
Front passenger door lock switch


?€¢
Door lock actuators in each of the doors


?€¢
Door lock system fuse into the BCM (BCM D 25A fuse)


Door Lock Operation
When the BCM detects a transition of either of the door lock switches to the LOCK position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the Lock position.
Driver Door Unlock Operation
When the BCM detects a transition of either of the door lock switches to the UNLOCK position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the LF door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the BCM detects a transition of either of the door lock switches to the UNLOCK position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the Unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked seperate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed). This video on testing computer controlled door locks on a Subaru , doesn't matter . test yours same way > The BCM controls your door locks .
Are all of the power door locks inoperative from both door lock switches?

Oct 12, 2016 | 2005 Buick Rendezvous

2 Answers

2005 Chevy Equinox Driver & Passenger Door Unlock Relay. How To Remove & Install. They Are Power Locks. Front Doors Must Roll Windows Down Use Hand To Open Thanks. Ms. J. C.


Door Lock and Unlock Operation
When a door lock switch is activated in the lock or unlock position the BCM will receive a voltage signal on either the door lock switch lock or unlock signal circuits.
The BCM, upon receipt of a lock switch lock or unlock signal, will switch the appropriate lock relay control circuit(s) to battery positive voltage. This will energize the appropriate lock or unlock relay(s). The relay will supply voltage to the door lock actuator lock or unlock control circuits to one side of the lock actuator. Since the opposing side of the lock actuators are connected to ground through the other lock actuator control circuit and the normally closed contacts of the lock or unlock relay, the doors and liftgate will then lock or unlock appropriately.
Three relays are used to operate the lock. Driver door unlock, passenger door unlock and all door lock. This is done to isolate the driver door lock actuator so it can be unlocked by itself using the keyless entry transmitter.
Your door locks are controlled by the BCM - body control module (a computer ) . An a scan tool is a must to diagnose system operation . Your best bet would be to take your vehicle to a qualified repair shop . The only way you could try to fix this is by changing parts ! Suppose you find an replace a door lock/ unlock relay an that doesn't fix it ? There could be DTC'S stored in the BCM . Do you know what a DTC is ?
?€¢
DTC B3132 All Door Unlock Circuit Low


?€¢
DTC B3133 All Door Unlock Circuit High




Your

Aug 10, 2016 | Cars & Trucks

1 Answer

Lock control #3 on Electrolux slide in range


I appreciate your post, Billy!
I understand that the lock control will not unlock on your Frigidaire range. I noticed that you have disconnected the electricity and the range is still not unlocking. I would recommend holding down the clear/cancel button for at least 15 seconds. If that does not unlock your range I would suggest that it could be a possible issue with your door lock or control panel. For any repairs to be completed I would recommend having a professional technician out to complete a diagnosis. This will help you avoid any unnecessary part purchases. Hopefully this information is helpful. -Matt

Mar 08, 2015 | Electrolux Kitchen Ranges

1 Answer

Whats the network lock control key for telstra


Do you want network unlock control key for your samsung gt-s3850 mobile phone? Yes means you can visit this site Unlock-Zone.com here you can get the network unlock control key (unlock code )and unlock your mobile easily. To get the code you have to mentioned which country is locked now,network provider,which country is locked now,network provider and imei number. Then they send unlock code through email.

Unlock-Zone.com

May 26, 2014 | Samsung Galaxy Ace GT-S5830

1 Answer

The controls locked is displayed. what causes this and how do i get the controls unlocked.


  1. Press and hold for 3 seconds the "Control Lock/Unlock" button on the control panel to lock the control panel.
  2. Listen for a double beep and observe the "Control Lock" status light is lit when the control lock is in effect.
  3. Press and hold for 3 seconds the "Control Lock/Unlock" button on the control panel to unlock the control panel. The "Control Lock" status light is goes out when the control panel is unlocked.

Jan 11, 2011 | Whirlpool GEW9250 Electric Dryer

1 Answer

How to recode remote to vahicle


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. A maximum of 3 remote controls can be programmed. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press lock or unlock button. Within 10 seconds: Press lock or unlock button of first remote control. System should now lock or unlock vehicle. Press lock or unlock button of second remote control. System should now lock or unlock vehicle. Press lock or unlock button of third remote control. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed remote controls.
NOTE: If less than 3 remote controls are to be programmed, remove ignition key after programming last remote control.

Jan 18, 2010 | 2003 Honda Civic

2 Answers

Unlock control lock in washing machine, whirlpool, duet


Hold control lock for 3 sec. It will make a sound and the door will unlock.

Mar 21, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Control locked on ghw920 can u help me unlock


theres abutton off the end of the control panle( youll need to lok closely) but marked "control lock hold for 3 secs"

Mar 04, 2009 | Whirlpool Washing Machines

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

1,644 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

prem mathew

Level 3 Expert

662 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...