Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool fills up between loads

You suggested a $10 part to fix this problem? Is it something that can be purchased in stores or is it online. We need our machine back asap.
My machine is a 9100LWJ, ser csp1403388.

Thanks for any help you can offer.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 246 Answers

I don't know whoi suggested a $10 part to you, but Sounds like you need a new water valve (some debris inside the valve causing it to not fully close). These are availible from your local appliance parts store or on line from the manufacture. Once you have your replacement, just take the 3 #20 torx screws out of the rear of the top panel slide the whole panel slightly towards the rear and lift it off. On the outside of the washer on the back panel, You should a light blue plastic thing that the 2 matching hoses from your house connect to. Turn your water off and remove these hoses. Just beside them you will find another #20 torx bit screw (some models use a #10 or #15). Remove this screw as well and slide the valve slightly to the side. It will come loose. Now from the inside of the machine, you will see 4 blue wires going into 2 connectors on the valve. Remove these
connectors only by pulling on the connectors, not the wires. Lastly you will see a small black hose with a green or silver clamp on it. Squeeze the clamp with a pair of pliers and then slide it down the hose. The hose should now pull free of your old valve. Re-assemble in reverse.
Please remember to rate this information if it was helpful to you. Best of luck and drop me a note if you have any troubles.

Posted on Jul 25, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Whirlpool duet ghw9400plo

Check the power input from the plug with a device which looks like a plug-in with six lights which can be purchased from a bigbox store and sells for less than 20 dollars, it tells you exactly what is wrong and if there is something wrong with the plug, I would suggest checking ALL of the plugs in the house and mapping out the electrical on the panel


Aug 15, 2014 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I have a Whirlpool ZUltimate Care II Washer, Model 3XLSQ7533JQ2. Washer keeps filling in the medium and the super wash level and will not go into the agitation cycle. Works on small load level only.


SInce the washer works ok on the small load size yet overflows on all others the problem is going to be with the water level switch and it should be replaced to remedy that problem.

The part number for that water level switch is W10339229 it could be purchased at your local appliance parts store or online at


Oct 13, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Where can i find transport bolts for Whirlpool Duet washer


Whirlpool has a part number for those shipping bolts,its W10289554A it can be purchased at your local appliance parts store or online at


Sep 26, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Ultimate care washer is very slow to fill on the cold side. I have cleaned the inlet screen and swapped the lines to test things. What could be the problem inside the machine?


The problem is going to be the water inlet valve..the solonoid for the cold water side is very weak and hardly opening. The water inlet valve should be replaced to fix the washer

This youtube video will show you who to replace that valve

The part# for that valve is 285805 it could be purchased at your local appliance parts store or online at;


Sep 01, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Whirlpool Ultimate Care II LSQ9549L top load washer -- hot water okay at inlet on back of unit, but won't fill tub. Is it a valve or a clogged line inside?

Most likey a bad water valve. You can replace it with just a few screws and a pair of pliers for the hose. You can test by swicting around hoses and the plugs on valve if you'd like to test it then try the machine on cold wash(it should be hot). While you switch them inspect the screens for rust and any clogging. Good Luck, Mastatech

Aug 21, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Whirlpool washer WTW57ESVW0 won't fill with water. I bought this machine two months ago was working fine and then just stopped filling water. Spin cycle and drain cycle work but it won't start fill...

Solution for WTW57ESVW0 Whirlpool Washer that won't fill or agitate, but will spin and drain water.

Replacing the Auto Load Sensing Switch (W10177795 - Illus. No. 12 on Control and Rear Panel Parts) fixed the problem.

In addition, a defective switch can also cause the machine to start agitating while it is filling.

It is relatively easy to replace and there are online videos that can help with the replacement.

Oct 27, 2010 | Washing Machines

1 Answer

Oil Leak-New washing machine

No sounds like you have a bad trans,but the good news is it's warrantied for the first year. call Whirlpool or register and schedule online

Sep 13, 2009 | Kenmore 3.2 cu. ft. Top Load Washer

1 Answer

Whirlpool LXR9245EQ2 top loading washer tub won't fill

try taking the knob off and see if the nut is tight on the timer,it might if came loose

Jun 18, 2009 | Whirlpool Washing Machines

1 Answer

$10 fill valve?

not sure about the $10 replacement (i think it was20-30). if you search for "whirlpool washer fill valve" on the net or on something like ebay, you will get something. alternatively you can try searching on the actual part number.

the mount on generic part I ordered was upside down. So i just mounted it to a piece of 1x2 to reinforce it.

Jul 13, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Duet leaking

leaking water inlet valve very easy solution!!!chat with me online and ill step you through it save up to $65 (my in-home rate in florida is $75!!!!!!!)

Sep 16, 2007 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal De

Level 3 Expert

2696 Answers


Level 3 Expert

79024 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides