How do I replace or fix the paper pickups? - Martin Yale Premier/ : Six-Sheet Collator, 11-1/4"x12-3/4"x9-1/4", Gray -:- Sold as 2 Packs of - 1 - / - Total of 2 Each

• First clean the sensors
• If Problem persists change Pickup rubbers.
• If problem Occurs replace the pickups
• Check and clean the Pickup sensor
• Then check and clean registration(Steel rod) sensor
• Then check and clean Fixing unit sensor.
• And finally check and Clean the Delivery sensor.
• Don't use air blowers and Hard cleaners just use cotton and brush.

Dear Abdullah
pl. check the machine base where it stay, it should be plain and firm.
Next check the left side door(test it by pushing inside while making copy). check the fixing assembly and paper path, may be toner clogged on its surface.
If your machine covered more than 200000 A4 copies, check the paper path (guide) at registration sensor and delivery guide at fixing unit.
If the paper jam at paper pickup tray, replace the pickup roller set (2nos.)

Since you have not mentioned the page counter and where paper jam occurs, its difficult to assume more.

thanks.

This should help. Good luck !

Cassette (Tray 2) paper pickup and feed rollers

To remove the paper pickup and feed rollers

1 Remove the cassette.

2 Locate the two rollers on the bottom of the paper pickup unit (above the cassette). The pickup

roller is the smaller roller, and the feed roller is the larger roller.

3 Pinch the tab on the end of the cassette pickup roller (callout 1), and pull the roller out.

4 Pinch the tab on the end of the cassette feed roller (callout 2), and pull the roller out.

Figure 6-24 Removing the cassette pickup and feed rollers

Note Always replace the cassette pickup roller and the cassette feed rollers at the same time. Also replace
the separation roller (located in the paper cassette) when replacing these rollers

This seems to be a common problem for the Canon ir 20 xx series machines. The problem is having machine indicating paper jams on the left hand side of the machine. When you open the left cover you do sometimes find paper stuck on entering the fuser unit. The main problem, and loads of these machines with these problems have been fixed, are the half moon pickup rollers! Clean the pickup rollers or even better, replace them and you will get the machine working 100%!! To confirm this try copying from the machine using the manual feed tray. You will never get a paper jam. This fault is due to incorrect pickup resulting in timing problem and thus getting paper jams! Good luck!

Replaced seperation pad?. separation pad work is to block multiple paper feeding,but in yourcase paper not at all feeding means paper pickup roller not picking up the papers.replace both 2 & 3 paper pickup rollers..
See the snap shot,view from under.
Pickup roller( red)
Un lock to remove pick up roller(blue),observe the angle of the roller & same way insert new one other wise it wont fix..
Bee care full while removing roller, paper sensor flag should not distubed(yellow)
bee pateince dont do harsh..best of luck.

there are several fixes to this problem 1. replace pickup asembly 2. Clean the rubber pickup band are roller with a rubber cleaning compound (not alchohol0 alcohol dries out the rubber.
This is a common problem with printers and faxes, Paper has a tendency to leave a glass glaze on the pickup rollers therefore causing the paper to slip on the rollers are to be misfed thus causing a paper jam

Alot of time it is the pickup rollers get smoothand won't pickup the paper. Replacing the rollers will fix that problem.

There are rollers that cling on to the paper and move it through the machine. When the rollers are worn down they do not grip the paper. For a short fix you can get something rough like sandpaper, brillo pad, etc, and gently scratch the rollers to give them some traction. This will temporarily solve your problem until you can get the rollers replaced.

We have many of the 1700N printers and have found that the 2 paper pickup tires must be in good condition to avoid frequent jams. I would highly suggest replacing the 2 paper pickup tires if this printer has a lot of copies on it.You can slip the tires off of the plastic roller and see if they are shiny. If so, replace them.

If it's not working all the time then the lifting mechanism is bad.
if it is and jams then the tire is slipping and causing the jam.
clean tire with alcohol and try is it really smooth or does it feel rough? if smooth then replace