Question about Sony Amplifiers & Preamps

1 Answer

Sony reciver error 12

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 30 Answers

Take big heavy hammer

lift it above your head

with one fast swing let it come down on top of the receiver. Please make sure the receiver is not plugged in when you do this.


Sony hasnt made a good receiver in a long time.

Posted on Aug 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Amp going into protection


Is the amp bridged? If you only have one speaker connected to it, I sure hope so. How much power can that speaker safely handle and what is the impedance of the speaker? 2,4,8 ohm? A 1200 watt amp with only one speaker may be too much amp.

Jan 14, 2014 | Sony Xplod 1200W Class AB Bridgeable 2-Ch....

1 Answer

Hi, My S-Master 5.1 Digital Amplifier can't read any DVD and every time it give a no disc error, i tried many DVDs with no good except one time it worked fine and after that the same No Disc error every...


Most disc read errors are caused by dust or dirt on the lens of the DVD player. You should follow the cleaning instructions. Or watch a YouTube video on cleaning DVD lenses.

Oct 12, 2013 | Sony TA-N9000ES 5-Channel Amplifier

1 Answer

Distortion sound


probably crossed ground/ positive connections. if not u have bad channels or a blown reciver

May 04, 2012 | Yamaha P3500S Amplifier

1 Answer

What size fuse do i use on the power connect cable?


Folow the Ohm's Law
I=P/E I=800Wats/12 Volt I=66.6 Amps' give litlle room for Peak-On so 67Amp should do.
Cheers

Aug 22, 2011 | Sony Xplod 800W Class AB Bridgeable...

1 Answer

YES I HAVE A SONY STR-AV770X RECIVER. AND A PYLE PRO PDG 4000 POWER AMP AND I WONT TO RUN MY BOSE 901 SERIES VI SPEAKERS WITH THE ACTIVE EQULIZER FOR STEREO MUSIC ONLY AND USE MY SONY RECIVER FOR THE...


There's no reason you can't use the 901's in ALL of your audio experience.

Try this:

Remove the short plugs from the Adaptor jacks. They claim you can record some of the effects (surround, dbfb and tone) from these jacks so that implies it's late in the preamplification path. The question is - did they place it after the Volume Control, too - as many other receivers with jumpers do?

Take an RCA pair from the Adaptor Out to the 901 Active EQ's Line IN; then the EQ's Line Out to a separate amp's Line IN. Attach the 901's to the new amp.

Because we don't know if the Volume Control is in the path at this point, find yourself a CD with a long, low fade-in just in case the signal is at maximum power here. Be ready to Pause it if it gets too loud.

If the Volume Control affects it ok, then get yourself a pair of RCA cable splitters and place them where the Adaptor Jumpers were with the extra leads going to the cables we ran to the 901 EQ at first. That way the receiver still keeps the program internally for its own speakers and the 901's get it, too, but without modifying what the receiver sees.

If the volume control on the Sony isn't in the Adaptor loop you'll have to use the Pyle's volume control. But you could still have the speakers that are directly attached to the Sony useable at the same time.

Mar 25, 2010 | Amplifiers & Preamps

1 Answer

I have 2 questions will my SONY TA-E9000ES preamp work with my SONY STR-DG720 7.1 RECIVER and what SONY ES Amplifer was spefically made to work with the TA-E9000ES WHEN IT WAS ORIGANLY PRODUCED


Here's a page for the 1st one

http://home.online.no/~espen-b/ta-e9000es/

It will work with your 7.1 receiver. Just use one of the inputs on the 7.1 to connect to the Pre-amp

PLease rate my help if this helps

Thanks

Nov 04, 2009 | Sony TA-E9000ES Amplifier

1 Answer

Distorted sound.


try to set up again may be cable instalation not properly to set

Aug 13, 2009 | Sony Xplod 1200W Class AB Bridgeable 2-Ch....

1 Answer

Settings for a Sony Xplod 1200 watt amp, with two 12 inch subs


What kind of subs are you running? Meaning what brand, what are the ohm, spl and wattage? I'll look up your amp while you get that info to me. Looking forward to helping you:) Thanks!

Apr 08, 2009 | Sony Xplod 1200W Class AB Bridgeable 2-Ch....

1 Answer

I need a code to unlock my TEAC AG20D


i need a code to unlock my ag20d reciver

Apr 07, 2009 | Teac Amplifiers & Preamps

1 Answer

Sony xplod 1200 watt


i had the same ploblem with my amp then i found out i didnt have a good enough ground. Make sure you groung it to your weel well or some part of the frame. Or you mite be running with a fuse thats pushing to much power i use a 100a fuse 5 gage power cord to power my 1200w xplode and my 2 12" kicker comps. Or if your using two diff kind of subs then you amp is confused in why your asking for 500w on one side and 600w on the other this will also make your amp light come on.

Jan 19, 2009 | Sony Xplod 1200W Class AB Bridgeable 2-Ch....

Not finding what you are looking for?
Amplifiers & Preamps Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Amplifiers & Preamps Experts

 Grubhead
Grubhead

Level 3 Expert

4585 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68258 Answers

Are you a Sony Amplifier and Preamp Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...