TV would not turn on. TV tech tried changing the power module. Now says that there is a short in the wiring harness and that he has to test each wire. Have been witout the TV now for three weeks. Does his answer make sense?
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Technician (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
One thing you can try is to remove all cords attached to the tv including the power cord. wait a few minutes( maybe say a short prayer) then plug the power cord back in and try turning on the tv if it powers up. it maybe a short in one of the units that were plugged into the tv. If it still does not work it maybe a circuit board problem. Sony Bravias have been plagued with a lot of circuit board issues. type in Bravia problems on any search engine and you will see what I mean. You may be able to get it repaired but you best course of action is to buy a different tv. a Vizio or Samsung or anything but a Sony
okay my friend your tv vertical circuit is begining to get faulty you could be having some bad caps or the vertical ic is defected have a tech check your tv for repairs.if you are not a tech you cannot repair the set by your self.good luck.
Check to see if you have a short to ground down by the starter, particularly to see if any of your wires are melted/touching your exhaust. there would be other problems if this is the case, so you need to check the wiring harness to the module and if that's OK, I am thinking you have an ignition switch wiring harness issue. also, check your wiring from the module to the fuse block for shorts there or at fuse block.
Hi Anonymous, before diagnosing any turn signal issue make sure the bulb is good and the light fuse has continuity. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. For more information about your issue, please visit the websites below, and for specific information or questions, please feel free to contact me at firstname.lastname@example.org. Good luck and have a nice day. Harley Davidson Wiring Diagrams and Schematics Harley Davidson Manuals Mark Workshop
Is this P0605 and P0700? If so read on. P0605 - Control Module Fault Possible causes- ECM/PCM Harness power supply circuit is open or shorted - ECM/PCM Harness ground supply circuit is open or shorted - ECM/PCM may be faulty P0700 CHRYSLER - Transaxle Control System (TCM) Malfunction Possible causes- Shorted or open circuit within transmission control module (TCM) - Failure of transaxle control module Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem
93-95 Mb was forced to use biodegradable insulation on its wiring in there cars by the US. Try looking at the engine wiring harness because they can short out. Also the Throttle assembly has the same wiring, it would cause all those problems.
i have seen a couples mitsubishi and i all ready talked with a tech suport from mitsubishi but they said change the capacitors in the shop were i work we do the same but the tv still doing the same then we send the dm module to them and they fixed we asked whats the real problem and they said the capacitos the best i think is send the module to them
Usually, in those Sony sets, a crack developes on a small transformer in the horizontal drive circuit, which causes the horizontal output transistor to short. This immediately shorts out the switching transistors in the power supply and blows the Sony 0.1 ohm resistor fuse. A shorted flyback (high voltage) transformer will also have the same result. The power supply does NOT need to be replaced. The parts should be replaced, the flyback checked and the board resoldered by a qualified tech familiar with Sony sets.