Question about Yamaha R-V1103 Receiver

1 Answer

Yamaha R-V1103 receiver cuts off immediately when turning unit on

No changes were made prior to this problem. I disconnected and reconnected one cord at a time in the back, then disconnected all cords. This did not reveal any short from the cords. What should I try next?

Thanks,

Scott

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 151 Answers

Sorry but it sounds like you have a fault,guy came into shop were i work with same problem,i tried cables etc as you have but had to send it back to yamaha.It came back fixed with report saying board replaced,sorry can not remember which board.

hope this helps
CABLE GUY.

Posted on Jul 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Onyko tx nr616 receiver keeps shutting off. Only stays on for approximately 3 seconds. Can you help?


The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and reconnect an input and a pair of speaker wires onto the unit. If the receiver still does not turn on than you will have to bring it in for service. Turn up the volume and if the receiver doesn't shut down, power off the receiver and add another pair of speakers. Power up the unit again and turn up the volume. If it doesn't shut down, power off the unit again. Now connect all your input sources and turn on your receiver. If the unit shuts down again, your unit will need to be further serviced at an authorized Onkyo service center.

Sep 30, 2014 | Onkyo Tx-nr616 7.2 Thx Certified Network...

1 Answer

How do i check to see what is causing my receiver to shut off


The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and reconnect an input and a pair of speaker wires onto the unit. If the receiver still does not turn on than you will have to bring it in for service. Turn up the volume and if the receiver doesn't shut down, power off the receiver and add another pair of speakers. Power up the unit again and turn up the volume. If it doesn't shut down, power off the unit again. Now connect all your input sources and turn on your receiver. If the unit shuts down again, your unit will need to be further serviced at an authorized Onkyo service center.

Sep 25, 2014 | Onkyo Audio & Video Receivers

1 Answer

Onkyo ht-rc180 standby light blinks will not start.i tryed factory reset, still blinks


The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and reconnect an input and a pair of speaker wires onto the unit. If the receiver still does not turn on than you will have to bring it in for service. Turn up the volume and if the receiver doesn't shut down, power off the receiver and add another pair of speakers. Power up the unit again and turn up the volume. If it doesn't shut down, power off the unit again. Now connect all your input sources and turn on your receiver. If the unit shuts down again, your unit will need to be further serviced at an authorized Onkyo service center.

Sep 24, 2014 | Onkyo Ht-Rc180 7.2-Channel A/V Surround...

1 Answer

Speakers are ok but when conected to the receiver some have sound some don't.


Yamaha R-V1103 Receiver is a good but old unit.

Check each channel for output.

May 21, 2014 | Yamaha R-V1103 Receiver

1 Answer

I have an Onkyo Tsxr 577 amp. The wires on the speakers crossed and the amp stopped working. It might be in autoprotect mode and I don't know how to reset it.


The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and reconnect an input and a pair of speaker wires onto the unit. If the receiver still does not turn on than you will have to bring it in for service. Turn up the volume and if the receiver doesn't shut down, power off the receiver and add another pair of speakers. Power up the unit again and turn up the volume. If it doesn't shut down, power off the unit again. Now connect all your input sources and turn on your receiver. If the unit shuts down again, your unit will need to be further serviced at an authorized Onkyo service center.


To obtain service, take or ship your Onkyo product to an Onkyo Authorized Service Center. Please also include in any mailing a contact name, address and telephone number. Please include a copy of the original sales receipt/invoice as well as a letter stating what the problem is, with your name address and phone number so the service center knows who to return the unit to. Please note, before shipping, you must contact the authorized service center to inform them that you will be sending your unit in for repair.

Feb 22, 2011 | Onkyo TXSR577 71 Channels

2 Answers

Pioneer receiver vsx d814 amp error


The Pioneer VSX-D814 has a couple of Power Hybrid bricks that do all the power amplification. These are the infamous PAC011A. You should have 2 of those in your receiver.

If the amp detects some unusual activities, it may shut down the unit to prevent damage. “Amp Err” usually means some DC in the output.

Disconnect all the speakers and turn on the unit; if it acts normal, reconnect speakers one set at a time very carefully. If the unit still shows the error message you can try to reset it. If the reset works, again carefully reconnect the speakers connections. If the reset does not recover the normal operation of the unit, you may have one of the PAC011A damaged, and the unit will need repair.
The reset can be done by disconnecting the unit power cord for a few minutes, then plug it in and press “FRONT ENTER key + ADVANCED SURROUND key” continuously for 2sec.

Good luck

Dec 18, 2008 | Pioneer VSX-D510 Receiver

1 Answer

No remote control function


Set the large remote to "ALL" or "AMP" and it should work,the small remote is for zone 2.

hope this helps.
CABLE GUY.

Jan 13, 2008 | Yamaha R-V1103 Receiver

1 Answer

Sound gone


disconnect everything in the back of the unit. reconnect only the cd to the imputs. also,just to be sure, disconnect all speakers(label them). fire it up,play a CD, connect the speakers 1 at a time. If the 1st works you have hope ,if not, try each channel individualy.The one that reduces volume is the problem-maybe shorted cable, bad speaker,or , God forbid-Bad amp Channel. good luck

Dec 30, 2007 | Yamaha R-V1103 Receiver

Not finding what you are looking for?
Yamaha R-V1103 Receiver Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio & Video Receivers Experts

Larry Stiles
Larry Stiles

Level 2 Expert

286 Answers

jonpoint

Level 1 Expert

4 Answers

Are you a Yamaha Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...