Question about Rangemaster 110 (Dual Fuel) Dual Fuel (Electric and Gas) Kitchen Range

1 Answer

Oven will not ignite

Timer is stuck on 'auto 0.00'. Reset button does not clear the problem. How do I clear this?

Posted by on

  • 2 more comments 
  • brenda397 Aug 14, 2008

    TIMER STUCK AT 0.00 AUTO AND OVEN NOT IGNITING

  • nuttynat_101 Oct 23, 2008

    timer on zero and no gas coming through so ovens wont ignite

  • Anonymous Mar 08, 2009

    Clock keeps going back to 00.00 and flashing and then has auto written down the side and the oven won't light.

  • tugger no1 May 04, 2009

    can not get top unscrewed to lift off as screws will not budge have clock flashing auto ooo, i can not change this, as you have described.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Rangemaster 110. Ovens not lighting due to faulty auto/clock. FIXED!
Someone, somewhere on the internet had the solution to my problem but I can't find the link again to thank them! If you don't mind losing the clock/timer auto function this is for you and it's free! Just takes a bit of time.
Basically you need to lift/open up the LH &RH hobs to get at the wires behind the clock. You should see 2 blue(neutral) wires coming directly from the back of the clock. Pull them out and connect together - should be easy to click them together. Then the ovens will light - but you will lose the auto/clock/timer functions. We only used the timer so not a big issue. We didn't take the control panel off but we did take ages to unscrew the hobs etc Probably took us about 2 hours going back to instruction manual we found on internet and trying to work it out but I think we've saved a lot in not replacing the unit with the usual call out charges. We made sure electrical supply was switched off and just took our time. Really chuffed!
Comment by tinling, posted on Nov 06, 2008 http://www.rangemaster.co.uk/Siteimages/Site_311/BigMedia/RM110Gas_04_06.pdf

This should allow you to see the instruction manual for the 110. There was another one somewhere showing a diagram of how to link the 2 blue wires at the back of the clock but I can't find it again! By the way our cooker is 10 years old so maybe different from newer models. We didn't have to take of the front control panel we accessed everything by lifting up the hobs to get behind the clock/timer.

Hope this helps! Ovens still working just got to go and buy a wee timer.

Posted on Nov 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I tun oven on. Timer flashing from 000 to Auto. Can't set clock and no elements will function. Think it is something with the end button but can't remember how to fix it.


Try shutting power off to it for a few minutes, to make it easier just go to your breaker panel and flip off the breaker for the oven, wait a few minutes then flip it back on. Unless there is a button thats stuck down, which isn't very common on these due to the membrane type keypad they use, a power cycle to it should clear out whatever is wrong unless its another problem.

Nov 25, 2015 | Ovens

1 Answer

I have an old belling farmhouse cooker the hob works fine but the oven isn't igniting manually or by the electric ignition The timer is manual and is stuck on the red patch I can't seem to shift it ...


Take the tiny screws of there are loads down right hand side then release screws on hob once you can lift hob plates up. Undo the covers on back of timer clock control . Make sure you un plug from mains . Take the neutral of back of timer clock. This will allow your oven to auto ignite again

Jan 07, 2014 | Belling FarmHouse 931 Gas Kitchen Range

2 Answers

How do you stop, reset or change the remaining time on the Timer on the GE JES1142 microwave? Pressing Clear/Off does nothing. Do you just have to wait for the timer to run out? Manuel is wrong even on how...


The first thing I would suggest is a hard reset. Unplug the unit for a minute or so. Then plug it back in, set the clock and try again.

If that doesn't work, leave it unplugged for about 5 minutes.

Oct 27, 2013 | GE JES1142SPSS 1.1 cu. ft. Countertop...

1 Answer

Setting the clock on a brinks timer 44-1011


I finally found the instructions for the Brinks timer 44-1011 and they work.
    • BRINKS DIGITAL TIMER 44-1011 INSTRUCTIONS
    • CURRENT TIME SETTING
    • 1*Press and hold the OK button for 4 seconds. Hour Display flashes.
    • 2*Press +/MANUAL or - to select the hour. Press OK to confirm.
    • 3*Minute display will now flash. Press +/MANUAL or - to select the minute. Press OK to confirm.
    • 4*Press MENU to exit the time setting mode. Now the timer is in clock mode.
    • PROGRAM SETTING NOTE: This timer can be set up for up to 2 different programs. We will use PROG 1 for this example, however these steps can be repeated for any of the 2 programs. To cycle through the individual programs use the +/MANUAL or - after pressing MENU in step one until the desired PROG "#" is flashing. To clear a program setting hit the RECALL button when you have the program selected.
    • 1*Press MENU button, PROG 1 "ON" will flash, press OK.
    • 2*Hour will flash. Cycle with +/MANUAL or - to desired hour, press OK.
    • 3*Minutes will flash. Cycle through minutes +/MANUAL or - to desired minute, press OK.
    • 4*Program will be flashing again. Press +/MANUAL to get to PROG 1 "OFF" blinking, press OK.
    • 5*Repeat steps 2-4 to complete PROG 1 setting.
    • 6*When done setting programs press the MENU button to return to clock mode.
    • 7*Press +/MANUAL to have LCD showing either "AUTO ON" or "AUTO OFF" for the timer to execute the programmed settings.
    • DAYLIGHT SAVING TIME SETTING (DLST)
    • 1*In clock mode, press RECALL to turn on or off the Daylight Saving Time.
    • 2*Turn on DLST, the below of LCD shows +1H. Time is adjusted by adding one hour.
    • 3*Turn off DLST, +1H will disappear and LCD shows the real time. MANUAL OVERRIDE AND ALWAYS ON/OFF When in clock mode the +/MANUAL sign cycles through
    • 4 settings that serve as manual override. **ON - Indicates that the timer is in the ON mode, and will always be on regardless of the programmed setting. **AUTO ON - At this selection, the timer will come on regardless of the programmed setting, but it will follow the next programmed command. **OFF - Indicates that the timer is always off (i.e. the wall socket is turned off) **AUTO OFF - Indicates that the timer is in the OFF mode until the next programmed step that turns it ON.
    • NOTE: For normal timer function, the selection must be either "AUTO ON" or "AUTO OFF". RESET At any mode, press RESET for 5 seconds. All settings will be cleared, return to clock mode, 12:00 MO, AM, AUTO OFF will be shown on LCD
I hope this is helpful. It was a bear to find.

Dec 24, 2012 | Hardware & Accessories

1 Answer

'Select' button not working properly


Timer is not identified.
Copy following link to read specific troubleshoot steps, and help identify specific timer.
http://waterheatertimer.org/Woods-timers-and-manuals.html#troubleshoot

With digital timers, be sure to reset timer before programming, to clear stray memory traces. Repeat reset more than once.
Most timers today have 1 year limited warranty against defects in workmanship.
Brand name timers such as Woods, Intermatic, GE, Westek, Utilitec have specific warranty procedure, while promotional timers sold under Timex, First alert, Stanley, the warranty is less clear and probably underwritten by seller.
Add a comment with clear description of timer.

Nov 25, 2012 | Hardware & Accessories

1 Answer

My freezer is not working its defrosting everything. Is there a reset or something I can do to fix it?


No reset button . Having no model number I gotta guess your timer is stuck in defrost. You must find the timer and advance it into the RUN mode. If the timer is good I would next take a look at the relay on the compressor. They fall apart overtime:
themobilian_2952.jpg

themobilian_2953.jpg
If this is one of the fancier ice boxes with auto defrost mess
then your thermistors could be bad or control board gone south. More Here

Sep 03, 2011 | Whirlpool Refrigerators

1 Answer

Do I set the GE timer # 15089 to Auto on or Auto off for it to be activated. I had it on Auto on however the light stayed on all the time.


I don't have repair for defective timer.
Open following link to identify timer and download manual:
http://waterheatertimer.org/GE-timers-and-manuals.html#15089

Timer should be set to Auto ON for timer programs to run.
Auto OFF is temporary override, and timer resumes schedule at next set point.
ON is always ON
OFF is always OFF

If timer is not operating as expected:
Test outlet for correct polarity and electrical problems using cheap circuit analyzer from hardware store.
Timer programs can have conflicts. Make schedule before setting timer so there are no overlaps that cause timer not to function as expected.
Current time has not been set. Set current time including current day.
Set button has been accidentally pushed, and a number or CTD appear in display.
Timer needs to be reset to clear conflicting programming or error. Push reset button with paperclip and try programming again.
Timer is not able to handle intended load. All timers work for incandescent bulb. Connect timer to incandescent lamp and see if problem continues.
Timer is defective. Buy another timer from Home Depot and return defect in new package.

Aug 17, 2011 | Jasco Ge 7 Day Digital Timer 1 Outlet...

1 Answer

Resetting the timer for Auto


Open following link to identify timer and download manual:
http://waterheatertimer.org/Woods-timers-and-manuals.html#Hamilton

I do not know how to 'reset timer for auto'
The reset button is small round button with R

Manual says: "ON/AUTO/OFF" override. Press "ON/AUTO/OFF" or the
button with the "HAND" symbol to force the timer into permanent
"ON" "AUTO" program or permanent "OFF" mode.'

When within the programmed window (preset time period),
cycle through "ON/AUTO/OFF" button to "ON" mode
(indicated by lighted red LED above display), and then
"AUTO"

I have not tested this timer, but the manual sounds vague and confusing, leading me to believe you have to tinker around with the buttons and settings to make sense.

Add a comment with your experience so others with same-similar problem can benefit.

Also take advantage of fixya expert assistance live.
For a price, expert works with you while you work on timer or any do-it-yourself project.
Fixya is always less expensive than a service call.

Mar 26, 2011 | Vista Pro Digital 7-day Electronic Timer...

1 Answer

I have a digital wall timer that allows for settings over multiple days. Trued to reset it (remove a few memorized settings) by pushing 'reset'; but this had no effect. Do I need to press it for a longer...


You posted the question under ST01C timer.
This timer will clear all programs if you hold reset in for a few seconds until the screen starts blinking 12:00. The reset button is a small round button that you push with a paper clip.
The ST01C memory for current day can be cleared by removing battery for a couple minutes, but the day-to-day programming remains forever until timer is reset.

Each timer tends to follow the same pattern as described above when there is a small round reset that is pushed with a paper clip >> push, hold for a few seconds, timer resets.

Other timers have a larger button for Reset ... the timers with larger reset button usually require you to hold the clock button and reset button at the same time ... or some other button besides clock has to be pushed at same time with reset. You can try different combinations of buttons and hold both down for a few seconds.

If you reply to this response with your exact model and brand timer, I can look up the specifics for most timers

Oct 18, 2010 | Intermatic Inc. ST01C Digital In-Wall...

Not finding what you are looking for?
Rangemaster 110 (Dual Fuel) Dual Fuel (Electric and Gas) Kitchen Range Logo

1,279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rangemaster Kitchen Ranges Experts

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Ismael Rodriguez...

Level 2 Expert

162 Answers

paulcarew

Level 3 Expert

2403 Answers

Are you a Rangemaster Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...