Question about i-mate JAQ Pocket PC

1 Answer

Speaker problem i have i-mate jaq,but i am facing the problem when i talk person on other hand can not hear it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem. Activesynk version 4.00 installed from original CD which I got with i-mate JAQ but I saw the message on computer display, minimum requirement is version 4.1 so I get 4.1.4841.0 and installed but status shows connecting but it does not connect.

Posted on Sep 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to do factory reset of i-mate JAQ


here is how to do a hard reset:

note: all three at the same time
1)push stylus into soft reset hole + press FN key + press right soft key.
2) phone will restart to factory settings

enjoy.-->

Dec 25, 2008 | i-mate JAQ3 Smartphone

Tip

Hi, i got new Imate-jaq. I am facing problem in synchronising the imatejaq with...


Your battery has been depleted past a chargable state.  This is a due to a bad design in the phone that doesn't monitor the battery power state well enough.  It actually allows the battery to be taken under the minimum amount needed to recharge the battery. 

You can fix this, but do so at your own risk.

You can simply purchase a new battery, that will work, just been sure not to let it deplete the battery totally anymore.

Now, on to the fix

-Take out the battery.
-Get any usb cable you can find sitting around. (any usb wire will do, an old printer cable, anything with a usb end that can plug into your computer)
-cut one end of the plug off. You need to leave the side on that connects to your computer. Cut off the side that plugs into a device (printer, camera, web cam, etc)
-Strip the rubber off the wire and expose the wires inside.
-Separate the wires from each other. You will only be using the BLACK and RED wires.
-strip the very end of the black and red wires carefully using a wire cutter exposing the metal wire inside the red and black covering.
-Plug in your home made battery charger to your computer. Careful not to touch any exposed metal, as it will give you a small shock.
****WARNING****
DO NOT UNDER ANY CIRCUMSTANCES ALLOW THE RED AND BLACK WIRE TO TOUCH EACH OTHER
****WARNING****

-now carefully hold the black wire to the negative terminal on the battery (it should be noted with a black circle with a - in the middle). Then touch the red wire to the positive terminal (it will be noted with a red circle with a + in the middle).

Hold the 2 wires there for 20 seconds. Then quickly plug the battery back into the phone, and then plug it into a regular charger. Give it little bit of time, if you've done everything correctly the charge light should come on.

I had to repeat the last step again to get the light to turn on indicating it was charging.

You must not hold the wires to the battery for too long, 20 seconds should do it. You can overload a battery with this trick and actually make it explode if you hold it there too long. You are well within the few minutes needed to detonate the battery due to overcharging by sticking very strictly to 20 seconds.

Just be careful and you'll be fine.

One you get a charge light give it a few minutes in the off position, then try powering up the device and keep it plugged in until you get 100% charge.

Good luck,

Peter




on Dec 28, 2007 | T-Mobile MDA

4 Answers

Modem drivers for imate Jaq


Hi,

I have i-mate JAQ. I want modem drivers of JAQ for xp operating system.
Could you please tell me the path or the link.

Thanks in advance.....

Jul 19, 2008 | i-mate JAQ Pocket PC

2 Answers

Password


did u put a password??

Jun 11, 2008 | i-mate JAQ Pocket PC

1 Answer

BATTERY LOW PROBLEM


i have useing i-mate jaq my problem is zipper file is not working in my cell. so please solve my problem.

Apr 18, 2008 | i-mate JAQ Pocket PC

1 Answer

Internet sharing


I have I mate spl I want driver for cable modem

Feb 25, 2008 | i-mate JAQ Pocket PC

1 Answer

Why does the JAQ keep dialing 9 while in a call?


i believe it just the touch problem when it touches ur ear or face. better to keep phone in locked position. also go to following

http://www.youtube.com/watch?v=jCiQoBzW1D4

>>>babamanan@gmail.com

Feb 07, 2008 | i-mate JAQ Pocket PC

1 Answer

Synchronise and connection problem in Imate jaq


hello! pradeep
let me tell u if u r using windows XP as an operatin system
then activesync creates some problem it is better to download activesync 4.5 which is the latest one and your problem will be solved. you can download it from net...

Dec 28, 2007 | i-mate JAQ Pocket PC

Not finding what you are looking for?
i-mate JAQ Pocket PC Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top i-mate PDAs Experts

Bilal Ahmed Qureshi

Level 2 Expert

195 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

bharat patel

Level 2 Expert

268 Answers

Are you an i-mate PDA Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...