Question about Camera Accessories

1 Answer

Bell & Howell 466ZB manual

Need manual fast! Downloadable would be awesome

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 685 Answers

Try for instruction manuals

Posted on Nov 03, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Elinchrom fx 200 ri. How can I reset?

To reset your strobe, follow these steps:
1. Switch the unit "off"
2. While still off, with one hand, press and hold both the flash-power up & flash-power down buttons (#10 in the picture).
3. Keep holding the buttons pressed and turn the unit back on with your other hand.
4. The Digital LED will flash in fast mode for a few seconds. Release the buttons. The unit is now reset.

Support for Elinchrom products is available at the link, below, including downloadable manuals.


Oct 16, 2013 | Elinchrom Camera Accessories

2 Answers

I dropped my Ohaus about 3 feet onto carpet. Now when I turn it on it boots to the E screen everytime. Help!

I am an Ohaus technical specislist. I have unfortunate news. You scale is broken and there is no other way to fix it but get it repaired. You can send it to us at:
Ohaus Corporation
Atten: Service Department
7 Campus Drive
Suite 310
Parsippany, NJ 07054

Jan 02, 2011 | Ohaus CS200 Standard room Scale 200g X1g...

1 Answer

I bought a bell & howell movie projector, need parts

Well Bell and Howell have a website, so i would suggest rtying them first to see where the distributors local to you are. Or you can contact a camera store and see if they will accept it as a repair or supply the parts

Please rate my help++++Thanks for using FIXYA

May 12, 2010 | Camera Accessories

1 Answer

I bought an old Bell & Howell 253 AX and take-up isn't powered

Have you switched the switch on the front? It is black and about 1 1/2 inches tall. Don't worry I had the same problem at first with mine!! ;) I hope I can help!

Mar 12, 2010 | Camera Accessories

2 Answers

I have a Bell & Howell slide cube projector that has been packed away for many years. The rotating disk will not advance the slides for viewing. The disk seems stuck. I have been unable to find anyone...

I occassionaly experience the same problem. I don't know why it occurs, however; here's what I do to get the projector moving again: 1) Face the right side of the projector wherein the lens will be pointing to your right. on the middle top of the projector edge closest to you you will see a top access tab. 2) Move and hold the tab to the left and lift open the top of the projector. 3) On the edge of the rotating tray at about the 5:00 position (my guess as I'm not at the projector now) you will slot in the circular plate aligned with another slot on the fixed casing. Inside this sloted area there is a metal pieve that spans the slot across the two surfaces. 3) Take a screw driver and giggle this metal peice, pressing dow and releasing, and / or in and out, while pressing the slide advance advance forward and back. I found no ryhme or reason to this or that it readilly works after so many jiggles, however; it alsways does usually after anywherefrom a few seconds to a minute or two. This isn't a fix but a temporary workaround. I'm in the process of sulling my thousands of slide to be digitized, after which I will no longer need this wonderful legacy machine. Hope this helps. Regards,

Jan 24, 2010 | Camera Accessories

1 Answer

Film is not being drawn into the gears of my old bell and howell 1620 8mm movie projector

Check the drive belt, if the belt is too loose it will not pull the film inbeasuse ther is not enough tension on the pulleys and the belt will slip. If you need the belt, good luck finding it as there are nearly impossible to find.

Sep 25, 2009 | Camera Accessories

1 Answer

I iam looking for a Bell & Howell lam I have Super 8 Bell & Howel Projector Design 466 compatible s/n HH15105 The rpoejctor lamp is gone it' a 120v 5amps 60 cycle Can you help Where can I find thi kind of...

hi check this out
Great selection of Bell+Howell Products. Call 1-800-990-1900
check this

i hope ur problem will be rectified soon.

all the best

Mar 10, 2009 | Camera Accessories

1 Answer

Anyone dealt with a A99HW 35mm film scanner

Have you installed the software and running the scanner through the software?
Please see the FAQ below
Alan (20/08/2009)4-stars-small.gifThis works well scanning negatives when I eventually got it working on my Windows XP computer, the problem is the drivers, so did a search and found them here External link removed. The link can be requested via our technical department directly you need the one for XP only (FS-C1-VP). I also used an earlier version of Photo Impression6. I hope this is of help to many who have failed to get it running properly

So contact Maplin Tech support and they should be able to point you in the right direction of downloadable drivers or the correct procedure for installation and use.

Jan 21, 2009 | Camera Accessories

Not finding what you are looking for?
Camera Accessories Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Camera Accessories Experts


Level 3 Expert

96659 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68352 Answers

Are you a Camera Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides