Question about Epson PC Desktops

1 Answer

When i rebooted my epson RX425 software CD everything loaded up o/k .but when i go to print,on preferences page it comes up in Italian.How can i get it back to english as it was before

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 96 Answers

Uninstall the software and then reinstall it. Check carefully to make sure that you choose english if it gives you that option. If it does not give you that option, contact your tech support for that product in case they sent you the wrong cd.

Sometimes, you can browse the CD and look for the english install folder, usually labelled either Eng, or Enu

Posted on Jul 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I don't have installation cd of lexmark x2450. how can i do it to install?


Any drivers you need can be found on the lexmark website. Note that some printers need the software installed before hooking up the printer. I'd try to install the printer first. The software will tell you if the printer needs to be connected.

Jun 13, 2011 | Lexmark PC Desktops

2 Answers

How may i print for Both Side Printing?


Hi,

Both side printing depends on the printer. It's a feature which require a hardware in the printer known as Duplexer. Which automatically turns the paper and prints on the other side. Some printer may not come with duplexer but if they support duplex printing, you can but the duplexer for the specific printer and attach it at the back of the printer.

If your printer supports duplex printing, when you click on print, click print preferences as shown in the fig 1 below.

Fig1

shreysri_17.jpg

Click on finishing tab >> put a check on Print on both sides under document optoins section

Click Ok to close the preferences window

Click Ok to send the print job to the printer


Below is the series of images showing how to connect a duplexer.

FIG1

shreysri_9.gif
FIG2 - Press the buttons to take out the back cover
shreysri_10.gif
FIG3 - Connect the duplexer in the same place

shreysri_11.gif

Regards,
Shrey

Jun 04, 2011 | PC Desktops

1 Answer

Hello i m using hp product name-KQ311AA-ACJmodel no-a6450in and serial no-INA81008F5.problem is whenever power is switched on after booting when the option of loading either windows xp or windows-7 comes...


Hi, not sure exactly what you are describing here; you are I believe using dual operating systems? There does seem to be a conflick, causing niether operating sytems to bootup correctly. I will give you the procedure to delete and install one operating system, if this is not what you wish, can you come back to me?
Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} To install new version of XP. Insert XP CD into drive, reboot pc pressing ESC button, or delete in some machines. This takes you into BIOS, change your primary boot device to CDrom, save changes and reboot. Select boot from CD once this appears and wait for files to be installed. Select the part of the hard drive you wish to use for your operating system (usually the largest) and select partition this drive. Delete any previous os, and reformat hard drive. (Be aware this removes everything saved on your hard drive, so always back up first) Re boot afterwards and reinstall of operating system will commence automatically (do not select boot from CD here).



Jul 08, 2010 | PC Desktops

1 Answer

Epson workforce 500 will not scan


All is well! I just followed some other person's solution (at a more responsive forum!) by downloading the latest .exe files from Epson and now everything is working just fine. thanks for answering my post above....ha, ha, ha. :)

Jan 21, 2010 | AcerPower Sn PC Desktop

4 Answers

Changing ink default to BLACK


Not possible.
Epson uses the black cartridge mostly, but also adds color to the black printing in order to keep the color inks from drying in the print jets on the printhead.
They also make lots of money that way...

===sorry===


Sep 14, 2009 | PC Desktops

1 Answer

I need to install my printer into my computer..?


Hi nikkita3

Try this method. Follow the link.
http://www.pptfaq.com/FAQ00605.htm

or you can try it this way.

How to install your printer software on your computer

So you have just bought a new printer and you're raring to go and print just about anything you can find in your computer. Before you amass all available pieces of paper, though, you should first install the printer software. This way, the printing process becomes smooth and easy. The good news is, most software these days will facilitate the installation on its own with just a few clicks from your end.
Here are a few quick steps in order to install your printer software on your computer:
Step 1: Read the installation manual
Before anything else, read the installation manual carefully. This is important. Take note of special instructions like if you need to uninstall a previous version of the software already in your computer or if you need to tweak some settings like turn your virus scanner off.
Step 2: Insert disk
Insert the disk or any media where the printer software is stored to the corresponding drive. You can hear faint whirring and buzzing sounds - this means the drive is reading the disk. Usually, a new window will pop up, displaying all the files read in the disk. Do you see a "readme.txt" or "readme.doc" file? Open that and read the contents of the file. There are usually important pieces of data or reminders in that file pertaining to your printer software. When you're done, look for a certain file that has a icon different from others and a ".exe" extension. This is the executable file. Click on it.
On the other hand, in case the window doesn't pop up, go to My Computer, click on the appropriate drive where your printer software CD is and look for the ".exe" file. Run that file by clicking on it.
Step 3: Installation proper
Once the executable file is run, the installation process will automatically begin. Get the box which came with your printer software CD and take note of the registration code or key. You might need to enter this data later during the installation process or when you need to reinstall the software all over again!
In the course of installation, you will be asked as to which folder you want to save all information related to the printer software, what type of installation (typical, custom or minimum) and which icon to use. It is highly suggested that you stick with defaults. Tweak the settings later based on your preference. What's important is that you install the software properly first.
Step 4: Reboot
More often than not, before you can fully use a newly installed program, you need to reboot your computer first. After rebooting, run your printer software and check if everything's working as they should.
So there. These are the steps that you need to do in order for you to install printer software on your computer. Just remember to do the necessary precautions like scan the software every now and then to make sure that things don't go haywire. Happy printing!

Sep 10, 2008 | PC Desktops

1 Answer

I have purchased a Advent Vista computer and my Epsom Stylus C84 CD wuill not load


Epson Stylus C84 Visit the link below, which should take you stright to the download page, where you will find the lastest drivers that support Windows Vista.

Just download and install the vista driver for the above printer.

Drivers & Downloads
http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=23953&prodoid=36033903&BV_UseBVCookie=yes&infoType=Downloads&platform=Windows&x=23&y=10

Jun 16, 2008 | Epson PC Desktops

1 Answer

I cannot get this Epson Stylus C88 Printer to Print


The garbage output and feeding blank pages is often a symprom of a corrupt
> driver.
> Uninstall the printer using the uninstaller supplied by Epson.
> This should be in START, ALL PROGRAMS and look under Epson.
> Run the uninstaller.
> Now open Control Panel and open Printers and Faxes.
> Select File/Server Properties/Drivers select the driver that refers to the
> Epson Stylus C88 and click on Remove.
> Disconnect the cable that is attached to the printer.
> Reboot the PC and reinstall the printer using the disk that came with it or you
> can see if there is a later driver on the Epson website.
> Do not connect the cable to the printer until asked to do so.
> Good Luck.

May 13, 2008 | PC Desktops

1 Answer

I am trying to use a Z705 color jetprinter, but cannot get it to print from the pc. I can print from notepad (not using the print file from the tool bar but from the notepad file. I have tried everything....


May be you are not installed well the software driver of the printer. First check the test page of the printer.

For test page see the option of the printer icon.right click icon goto the properties and click test page. Then it will not print well after that put the driver cd into the cd drive and install the software.try it and if the prob comes again please inform to fixya.com

May 12, 2008 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson PC Desktops Experts

Justin
Justin

Level 3 Expert

2072 Answers

 Jitesh Jalan
Jitesh Jalan

Level 1 Expert

27 Answers

rclarke250

Level 1 Expert

8 Answers

Are you an Epson PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...