Question about Dishwashers

1 Answer

Loose (plastic) doorhandle on Maytag dishwasher

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 254 Answers

If your dishwasher is a newer style the latch handle and latch are sold as assm, all you can really do is replace it.

Posted on Jul 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thermostat tripping


I just fixed my Maytag's bi-metal switch. I smacked it with the plastic end of a screwdriver. Problem solved. You may have venting issues in the dishwasher if it's continually overheating.

Jan 30, 2014 | Maytag Dishwasher

Tip

Maytag recalls dishwasher/fires feared from heating element


Maytag is recalling dishwashers for fire hazards including Maytag, Amana, Jenn-Air, Admiral, Magic Chef, Performa by Maytag and Crosley brand dishwashers with plastic tubs and certain serial numbers.


Check these serial numbers to see if you have the dishwasher in question.
Call 1-800-544-5513 if you think you have one.

on Jun 04, 2010 | Dishwashers

1 Answer

Check float valve


pull out your bottom rack, in one of the bottom corners of your dishwasher there will be a circular plastic piece. it is probably stuck in the up position . Wiggle it around, it should sit loosely in place. It's a float, so when water fills in your washer, the float should raise up, when the water is draining, the float should lower with the water. That's why the float should be sitting loose in position.

Dec 29, 2013 | Maytag Dishwashers

1 Answer

Maytag Dishwasher-MDBH945AWW


About the only things that move in the cabinet other than the water pump is the spray arms. The lower arm should be screwed down fairly tightly (plastic screw), but the upper arm is held in place with a plastic friction plug--it tends to wobble more. Spin both arms by hand to see if either hits something (have the drawers in). The lower arm has metal clips on the ends which may be coming loose. They are just clipped onto the arm edges. Hope this helps!

Apr 06, 2010 | Maytag MDBH945AWW / MDBH945AWQ /...

1 Answer

I am tryin to find a diagram or schematic for a maytag jet clean


i was able to obtain a drawing from repair clinic that helped to resolve my problem.

Feb 07, 2010 | Dishwashers

3 Answers

The handle on my Maytag Quiet series 100


I had the same problem with my QS 100. I disconnected power first via the breaker then removed the 11 screws. I couldn't loosen the two electrical connections, but the door pulled far enough away to inspect the handle mechanism. The plastic handle fell out of whole handle assembly rather easily because two molded plastic pins protuding from either side had broken off and were loose inside. There was also a pair of molded plastic v-shaped forks right on the panel to hold the handle assembly and these were damaged but they just to seem to act as guides only (as the handle assembly is held in by two of the screws that were removed). Replacing the v-shaped forks would require a whole new door which I am NOT doing. It looks like I can a replacement handle in the same color with new pins (I am reading they may now be metal) for about ##15. Pretty easy to disassemble and inspect, only about 15 minutes.

May 29, 2009 | Maytag 24 in. MDB5600A Jetclean II...

3 Answers

Maytag dishwasher Model MDB9150AWQ won't unlock


try this keystroke..."high temp wash" "heated dry" "high temp wash" "heated dry"

Apr 17, 2009 | Maytag 24 in. MDBH950AWS Built-in...

1 Answer

Portable dishwasher won't stay connected to the kitchen faucet


it the faucet connector has a lever u push in order to latch on to the faucet, just jam something under it so it maintains upward pressure and wont come unlatched when the water starts flowing

Jan 30, 2009 | Maytag MDB9600A Jetclean II Built-in...

1 Answer

Door handle


removing the front panel is just meccano. the screws are probably torex - a driver is easily available from any tool shop

Mar 24, 2007 | Gaggenau GI936-760 Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...