How do I reverse the door of the electrolux ede77550w

https://www.repairclinic.com/RepairHelp/Dryer-Repair-Help

Not all doors are reversible but the link above should help either way.

I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

Usually with door open there is 2 screws holding the locking assembly in place! Undo all screws and remove whole assembly! Refitting is reverse!

Hi Wendy, this is AP
I understand you want to reverse the door opening on your Electrolux dryer. I would be happy to assist you with those instructions. Are you able to provide the model number for your dryer? If this is a new dryer you may visit the manufacture website, locate your appliance, scroll down to bottom and you will see a listing of documents available, the installation instruction manual will have the reversal instructions listed. . I hope this information helps to some degree - thanks for your question, and please do not hesitate to reconnect if you have additional information regarding your question.

Thank you,

Hello paulascor549 - I completely understand that you took the oven door apart to clean it, therefore you must have took the following steps to do so. According from my research you would have to reassemble in reverse order. If you have already tried to do so and it proves to be ineffective, contact a professional to move forward accurately.

Door Removal and Cleaning of Interior Glass

Tools needed: Phillips head screwdriver or small quad bit driver.


A. Open Door remove 2 screws and washers on door lining at door hinge area.

B. Refer to owners guide? With door in broil stop position lift door assembly off hinges.

C. Lay door on table, position so that handle hangs freely over edge of table

D. Remove 2 screws and washers that secure handle to lining assembly.

E. Remove 8 screws that attach textured steel door wrapper trim to lining assembly 3 at top, 3 at bottom, 1 on each side

F. Lift door lining up and out of wrapper trim assembly.

G. Lay lining assembly on table with wool shield/inner part of lining facing up.

H. Remove 2 glass clamps via 2 screws per clamp. These clamps attach innermost clear glass to wool shield.

I. Lift out center clear glass from wool shield, this glass just lays onto the wool shield and is held in place by the glass/ clamps in item H.

J. Clean each glass with appropriate cleaner, Windex, bon ami, fantastic, etc

K. One glass that remains in door lining assembly can at this time be cleaned without further disassembly the lining assembly.

L. Reassemble in reverse order.

usualy only door reversible are on yhe dryers not the washers

Simple enough. Pull plug out and remove top cover of machine. There is a long way and short way so ill advise short way. The latter would require taking the boot off which needs expertise putting it back. Ok open front door and with screwdriver undo 2 screws holding the inner door latch. Place you one hand in the machine and then pull latch up high enough to allow you to pull wiring off. Note the position of those wires.(important). Once off, replace in reverse order, and test.

Im unable to look up htat particular model number for you, looks like my FRT18, which is made by the electrolux company, in which case, YES you can easily switch the door swing form one side to the ohter, whats on the left goes to teh righ and right to the left, not a problem

Basically they needed to supply an additional door mount for the left hand side of the door as well as the right hand side. Problem now sorted. Poor instructions in the manual didn't help here!

Electrolux has a reversible door for both front load washer and dryer. Just found that out at HHGregg because we need to put our washer to the right of the dryer, and none of the other makes will allow the washer door swing to be switched.

Hope this helps (technique used on EOG9330XN):
1) With the door open, on each hinge, there is a top cover which lies flush with the hinge. Simply swing this cover up and back towards you. This unlocks the hinge. Undo both and carefully close the door, holding it at the bottom. The door should be able to be pulled away from the frame now. Lay the door on a flat surface.
2) The oven will normally be attached to the surrounding built-in cupbpard. If so, unscrew all attachment screws (mine had at least three per side) and pull the whole oven out about seven inches, supporting if neccessary. Each side panel has a locating screw in bottom front corner, so remove the screw. Peel back the side panel (only thin alloy, but watch for sharp edges) sufficiently to see.....
3) The two side securing screws for the door hinge receiver should be visible. After pulling receiver forward, if loose, tighten securing screws (use lock washers if available, as Electrolux don't provide them).
4) Reverse the procedure to finish job, fitting the door in the near vertical position to engage hinges in the receivers. Support the door, lower to open position and flip the locking hinge covers back.
[This technique works if the hinges aren't worn and if the door doesn't close properly, it usually means that the receivers are loose and have been pushed back into the oven frame].