Question about Printers & Copiers

1 Answer

Case # 1021940 after i talked to you a few minutes ago the printer still prints missing a verticial line or two

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I went menu to clean print head

Posted on Jul 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After refiling ink, print is not getting corectly


Question is, was it printing correct before you refilled?
If not, the refill perhaps was not needed. Perhaps only cleaning the print head coulld have been enough. Print a head alignement page (just a little ink is used and only a few lines are printed) to check all the nozzles. When you see missing parts, you know you have to run one or a few cleaning cycles. When you don't use the printer often, please at least once a week switch it on and after a few minutes switch it of again. It will perform a cleaning cycle then, making the chanche of cloging minimal.

Apr 01, 2015 | HP PSC 1510 All-In-One InkJet Printer

2 Answers

I have a xerox printer phaser 8560. it does not seem to be printing and displays "Fault 37.016.43:23608. I have unplugged the printer as well as emailed xerox but no answer. Does anyone know what this...


I had one a few years ago. I think it indicates it is not hot enough to melt the wax (ink) caused by a failed heater. I replaced my heater with a halagon light bulb from the local big box store. Mine use to sort of flash white from inside the case until it warmed up then the flashing slowed down

Dec 10, 2014 | Xerox Phaser Printers & Copiers

1 Answer

My pixma mp500 is skipping lines when printing


If you have refilled with non genuine ink this could be the problem. Or you could test print a few pages in case there is a blockage

Sep 20, 2012 | Canon Pixma MP500 All-In-One InkJet...

1 Answer

My lexmark printer prints a few lines properly, and then it misses the next few lines, or only partially prints them. How do I correct this problem?


On your inkjet printer, start the Lexmark software,
and run a "print-head-cleaning-cycle", since some (not all)
of the ink-jets that shoot the ink onto the paper are CLOGGED.

Oct 07, 2010 | Lexmark Printers & Copiers

1 Answer

My Brother HL1230 printer prints with whole lines of text missing several times on a page and gets worse by missing more lines if printing several pages. It has a new toner cartridge. How can I sort this...


I have a brother MFC 3240C. My Black ink stopped printing(initially printed horizontal faded lines and gradually got worse), the other colors were printing fine. I tried cleaning numerous time( 50 -100 times over 1-2 weeks ). Still no improvement. The way I print now is:
1. I go to Printer Properties
2. Change Media type from "Plain Paper" to "Inkjet Paper".
3. Change Quality to "Photo".

This takes a long time to print 1-2 minutes per page. However, this works for me since this is my Home printer and use it for printing only few pages here are there.

Good Luck
RK

Jan 28, 2010 | Brother HL 1230 Laser Printer

1 Answer

Not fully printing any document


Print a test page and perform head clean if necessary.

Oct 17, 2009 | Epson Stylus Multifunction Inkjet Printer/...

1 Answer

Epson BX300F- not printing full pages


it means your paper is wonky and you need to tap them back upright every now and then, thats all

May 29, 2009 | Epson Printers & Copiers

2 Answers

Black ink does not print


I had the same problem and this is what worked for me.
If your color ink works fine but your black ink doesn't print at all it is because
of dried ink in your printheads and in your cartridge bay.
What I did was remove the black ink cartridge and noticed that the ink was dry and sticky in the slot.
I got a wet paper towel and just dabbed it in the slot and all of the black **** was on the paper towel.
I cleaned inside the cartridge slot some more, then dried it off with a dry paper towel.
I ran it though a few cleaning cycles then started to print again.
At first I just got the black lines, so I cleaned again and got illegible text.
Cleaned it a few more times, then I was able to read the black text.
And after running it yet a few more times, it now prints perfectly.
Hope that helps.

Jul 06, 2008 | Brother MFC-5440 Printer

2 Answers

Print result at 1st line ok..2nd line become blur..its alternate till end of printing


Replace the ink cartridge.
The cartridge is so wide that it can print 2 lines at a time, and the upper part of it is probably partially clogged. That's why every 2'nd line is blurred, and the rest is ok.

Jan 17, 2008 | Printers & Copiers

1 Answer

Missing characters, missing print barcode lines


Hi, It's been a while since I worked on these, so I'll go out on a limb (as far as my rating goes) and say that the few times I've seen that happen usually results from a bad network card. Now you may not be using a network card, so if your not then I'm not really sure what would cause that to happen on the printer side. The environments that I've seen that happen in are with an AS400 and the network card just gave out. You most likely tried this, but you might want to make sure that the computer isn't using one driver for both printers. Good luck.

Aug 28, 2007 | IBM 4039 Model 16L Laser Printer

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts

kakima

Level 3 Expert

96576 Answers

old marine
old marine

Level 3 Expert

1472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...