Question about Nintendo Video Game Consoles

2 Answers

WII REMOTE WILL NOT CONNECT TO THE CONSOLE - Nintendo Video Game Consoles

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 62 Answers

Make sure the batteries are fresh, and then open the battery compartment. There is a little red button. On the front of the Wii (turn it on), open the door where the SD memory card goes in. There is another red button. Press them both at the same time. The blue lights will flash on the remote, and it should then work.
Repeat for each controller.

Posted on Jul 12, 2008

Did that doesnt work

Posted on Aug 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot get cursor on screen , replaced sensor bar , but no joy ??


Does your Wii connect with your wii-remote(1 blue light on and not blinking)? If not try re-sync the wii-remote:

http://www.wikihow.com/Synchronize-a-Wii-Remote-to-the-Console

Apr 19, 2015 | Nintendo Wii Console

Tip

2nd wii remote will not connect


Wii Remote not being recognized by the Wii Console (lights on the Wii Remote flash when you press a button, but then go out) - Most Common:
Getting the Wii console to recognize (or "sync" with) a Wii Remote, especially one that did not come in the box with your Wii console, may require doing a few additional steps before it can be synced. Additionally, a Wii Remote that was working, but is no longer being recognized (or has "lost its sync") may need to be re-synced. Please use the troubleshooting steps listed below, which our experience has shown can solve many Wii Remote issues.
http://www.nintendo.com/consumer/systems/wii/en_na/ts/wiiremote.jsp
    Try these steps!
  1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.

  2. Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

  3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:
    1. With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

    2. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

    3. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console.

    4. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

    5. This sync procedure (steps "a" through "d" above) must be followed for each additional Wii Remote added to the system.

on Mar 04, 2010 | Microsoft Xbox 360 Console

1 Answer

My wii


What to do:
  1. Press the Power button on the Wii console to turn it on.
  2. Remove the battery cover on the back of the Wii Remote to be synced. Open the SD Card Slot cover on the front of the Wii console.
  3. Press and release the SYNC button just below the batteries on the Wii Remote; the Player LED on the front of the Wii Remote will blink. While the lights are still blinking, quickly press and release the red SYNC button on the front of the Wii console.
  4. wiiremotesynchstandard.gif
  5. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
This sync procedure must be followed for each additional Wii Remote added to the system.

Ref: http://www.nintendo.com/consumer/systems/wii/en_na/ht_system.jsp

Dec 16, 2012 | Nintendo Wii Console

1 Answer

I can't connect my controller to the wii console. Model number Rvl-001(USA). Model of nyko pistol accessory is Bn:090907 4632.My mom threw out the manual out by mistake.HELP!


  • Turn on your Wii console. While on the HOME screen, press any button on the Wii Remote.
  • If the 4 squares on the bottom remain dark, change the batteries (or for a rechargeable Wii Remote, place it on the charger for a while).
  • If the 4 squares blink blue, then stop, your Wii Remote is not synced. Press the 1 and 2 buttons at the same time. This should connect your Wii Remote if it's been synced before.
  • If your 4 squares still blink blue, then stop, these last steps will do the trick. First, on the front of the Wii console, just underneath the disc slot, there is a small panel that opens down. Open it and press the small red button.
  • Open the battery panel of your Wii Remote and press the small red button. Replace the battery panel and observe the blinking blue lights. If 3 stop blinking, and 1 remains lit blue, your Wii Remote is synced with your console.

May 13, 2011 | Video Game Consoles

1 Answer

My wiil remote will not connect to the console when i turn it on the blue light flashes but doesnt not connect


  1. Press the Power button on the Wii console to turn it on.
  2. Remove the battery cover on the back of the Wii Remote you wish to sync up, and press the SYNC button just below the batteries. The Player LED will blink.
  3. Open the SD Card Slot cover on the front of the Wii console and press the SYNC button on the inside of the compartment.
  4. When the Player LED blinking stops, the syncing is complete. The LED that is illuminated indicates the player number (1 to 4).

    wiiremotesynchstandard.gif

This procedure must be followed for each additional Wii Remote added to your system.
hope this helps

Nov 29, 2010 | Nintendo Wii Console

3 Answers

How do i set up a second wii remote to my wii console


    Standard Mode Synchronization
    Note: Make sure you have placed batteries in the Wii Remote (how to).
  1. Press the Power button on the Wii console to turn it on.

  2. Open the SD Card Slot cover on the front of the Wii console. Remove the battery cover on the back of the Wii Remote you wish to sync up.

  3. Press and release the SYNC button on the inside of the SD Card compartment on the console. Press and release the SYNC button just below the batteries on the Wii Remote.

  4. When the Player LED blinking stops, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
Hope this helps!

Feb 02, 2010 | Nintendo Wii Console

1 Answer

My controller wont hook up with the wii


In the battery area of the qii remote and inside the front panel of the wii console, there are connect buttons, push the red button on the console and remote to sync them together

Jan 01, 2010 | Nintendo Wii Console

1 Answer

Wii remote doesnot connect to the console. All batteries have been replaced


you gotta well you now the sd card slot the big thing thats neer the power and reset. Open that and you see that red button well now take off the wii remote cover and look for the little red button on the wii remote. Press the two red buttons at the same time and it will connect.
You can do this with aney one.

Nov 08, 2009 | Nintendo Wii Console

2 Answers

My wii counsel turns on fine, my remotes are with new batteries and flash when pressed the red light, but yhe remotes don't seem to be able to connect to the screen?


if your Wii Remote is not responding It may need to be synced up. I have given you both ways of syncing your Wii. After doing this Please don't forget to rate me as " Very Helpful" & feedback is appreciated - thanks

Synchronizing the Wii Remote with the Wii Console Synchronizing the Wii Remote to a Wii console allows the Wii Remote to communicate with the console. The Wii Remote included with your system should already be synchronized to your console. However, all additional Wii Remotes you use with your system also need to be synced in order to function properly..
There are two different modes of synchronizing (syncing):
  • STANDARD MODE - The Standard Mode procedure is used when adding additional Wii Remotes to your system or if you want to re-synchronize your original Wii Remote. Once synchronized, the Wii Remote will stay synced to the console unless you overwrite the settings by syncing the remote to a different console. For instructions on Standard Mode syncing, please read below.
Standard Mode SynchronizationNote: Make sure you have placed batteries in the Wii Remote
  1. Press the Power button on the Wii console to turn it on.

  2. Open the SD Card Slot cover on the front of the Wii console. Remove the battery cover on the back of the Wii Remote you wish to sync up.

  3. Press and release the SYNC button on the inside of the SD Card compartment on the console. Press and release the SYNC button just below the batteries on the Wii Remote.

  4. When the Player LED blinking stops, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
  5. wiiremotesynchstandard.gifThis procedure must be followed for each additional Wii Remote added to your system.


One Time Mode SynchronizationNote: This mode temporarily removes Standard Mode synchronization setup for all Wii Remotes until the power of the Wii console is turned off. When the power is turned back on again, the Standard Mode settings will return.
  1. Press the HOME Button on a Wii Remote that is synchronized with the Wii console.
  2. installation.gif
  3. Select the Wii Remote Settings option from the Home Button menu.
  4. homesmall.gif
  5. Select the Reconnect Option.
  6. wiiremotesynchotm1.gif
  7. Press the 1 and 2 Buttons at the same time on the Wii Remote that you want to synchronize with the console. If you are syncing multiple Wii Remotes, press the 1 and 2 Buttons on each Wii Remote immediately (without a significant pause) in the order you want them synced. The order in which you synchronize Wii Remotes determines the player order (1 through 4) for multiplayer games. The Player LED will blink during the syncing process. When the blinking stops, the connection is complete.
  8. wiiremotesynchotm2.gif

Sep 22, 2009 | Nintendo Wii Console

14 Answers

2nd wii remote will not connect with mario play 8


We had this same problem so I did a google search for 2nd wii remote not connecting or staying connected and this is what we came up with and did this and it really works! So hopefully this will help all of you to. Good luck! K and M

This is from www.nintendo.com/wii :

Wii Remote not being recognized by the Wii Console (lights on the Wii Remote flash when you press a button, but then go out) - Most Common:
Getting the Wii console to recognize (or "sync" with) a Wii Remote, especially one that did not come in the box with your Wii console, may require doing a few additional steps before it can be synced. Additionally, a Wii Remote that was working, but is no longer being recognized (or has "lost its sync") may need to be re-synced. Please use the troubleshooting steps listed below, which our experience has shown can solve many Wii Remote issues.
http://www.nintendo.com/consumer/systems/wii/en_na/ts/wiiremote.jsp
    Try these steps!
  1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.

  2. Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

  3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:
    1. With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

    2. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

    3. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture below).

    4. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

    5. This sync procedure (steps "a" through "d" above) must be followed for each additional Wii Remote added to the system.

wiiremotesynchstandard.gif

Dec 23, 2007 | Nintendo Wii Console

Not finding what you are looking for?
Video Game Consoles Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles Experts

Troy Gorman
Troy Gorman

Level 3 Expert

508 Answers

phil

Level 2 Expert

567 Answers

Raj Patel

Level 3 Expert

845 Answers

Are you a Nintendo Video Game Console Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...