Question about OKI Office Equipment & Supplies

Open Question

How to reset image drum on a oki C8600 - OKI Office Equipment & Supplies

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Niraj Limbu
  • 183 Answers

SOURCE: k image drum

Go to
menu>Configure Device>Print Quality>select Full calibrate now
once it's completed then run following action:

Menu>Configure Device>Reset>Reset Supplies>New transfer kit>yes

you are done but it works if there still remaining bit transfer kit if its run out then not gonna work.

Good luck and rate all answers.

Posted on Mar 31, 2009

Ad
pineworks
  • 4041 Answers

SOURCE: OKI C8600 Replace Image Drum - 563: K Drum Life

Solution:

  • Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed.
  • Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed.
  • Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed.
  • Press either the + or – button until “CONSUMABLE COUNTER SET” is displayed, press the Enter button; you are now in the menu to set various consumables.
  • Press either the + or – buttons to scroll through the various consumables, at the desired consumable press the Enter button and the last digit of the count will start flashing.
  • Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count.
  • Once the count is at the level you desire, press and hold the On-line, Cancel, & Back buttons simultaneously until the “*” reappears next to the count; consumable’s count are reseted to the number you specified.
  • Press the + or – buttons to move to the next consumable and repeat at step 5.
  • Once all consumable counts have been set to desired amounts that are below their end-of-life thresholds, you can use the Back, +, & - buttons to exit through the menus
  • until “INITIALIZING” is displayed.

Posted on Jan 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

OKI B410dn drum life


Every Oki B410d printer, Oki B410dn, Oki B430d, Oki B430dn, Oki B440dn, Oki MB460, Oki MB470, Oki MB480 are contacting the module of the Oki 43979002 drum and fuse with chip developed in the module imaging unit through joints being in the bottom part of a printer like in a photo. Eksploatacja Oki B410 pochodne drukarki reset kasowanie bbna

Jan 28, 2014 | Oki Electric Industry C8600n Led Printer

1 Answer

I HAVE C5500 OKI PRINTER AND THE ERROR SAYS REPLACE IMAGE DRUM 561:M DRUM LIFE I PUT IN NEW MAGELN AND STILL HAS THAT MESSAGE


oki printer c5950 fix new cartridge & drum coming error replace image drum 561:m drum life

Jan 15, 2013 | OKI C5500n Printer

1 Answer

OKI C8600 Replace Image Drum - 563: K Drum Life


Solution:
  • Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed.
  • Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed.
  • Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed.
  • Press either the + or – button until “CONSUMABLE COUNTER SET” is displayed, press the Enter button; you are now in the menu to set various consumables.
  • Press either the + or – buttons to scroll through the various consumables, at the desired consumable press the Enter button and the last digit of the count will start flashing.
  • Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count.
  • Once the count is at the level you desire, press and hold the On-line, Cancel, & Back buttons simultaneously until the “*” reappears next to the count; consumable’s count are reseted to the number you specified.
  • Press the + or – buttons to move to the next consumable and repeat at step 5.
  • Once all consumable counts have been set to desired amounts that are below their end-of-life thresholds, you can use the Back, +, & - buttons to exit through the menus
  • until “INITIALIZING” is displayed.

Oct 14, 2009 | Oki Electric Industry C8600n Led Printer

1 Answer

Resetting image drum after replacing for oki b4600


On the printer press the menu button until you reach MAINT.Then press the item + button until you reach DRUM CT RESET. Then press select.YOUR DONE

Oct 03, 2009 | OKI B4600 Printer

1 Answer

Oki b4600 displays check image drum toner senror error


Try this:

Press Online
Press Menu repeatedly until MAINTE MENU displays. Press Select.
Press Item+ until DRUM CNT RESET displays.
Press Select.

Jul 01, 2009 | OKI B4600n Printer

1 Answer

OKI C8600 service manual.


http://safemanuals.com/user-guide-instructions-owner-manual/OKI/C8600N-_M

I don't know if it is this but i hope it helps

Cheers

Jun 21, 2009 | Oki Electric Industry C8600n Led Printer

1 Answer

K image drum


Go to
menu>Configure Device>Print Quality>select Full calibrate now
once it's completed then run following action:

Menu>Configure Device>Reset>Reset Supplies>New transfer kit>yes

you are done but it works if there still remaining bit transfer kit if its run out then not gonna work.

Good luck and rate all answers.

Mar 31, 2009 | OKI B4600 Printer

1 Answer

OKI C8600 Printer Toner Sensor Reset


I've had two toners that have done this, they register as used as soon as you turn the dial to open the toner compartment. So if they don't work properly, as soon as you remove them.. you can no longer use them. (they empty contents into the drum).

I got in contact with my supplier and sent them back as faulty cartridges.

Sep 30, 2008 | Office Equipment & Supplies

1 Answer

Oki C8600 control panel detached when delivered...


nope..i'd send or take it back, myself..could be a loose ribbon cable underneath, too, eh?

Mar 06, 2008 | Office Equipment & Supplies

1 Answer

Okipage 8w print drum


To reset the drum counter on these it can be done by this
link to oki 8w Image Drum Cartridge instructions

http://my.okidata.com/man-8w.NSF/MOCContents/5577D9A2FD2AC576852566C100507580?OpenDocument

or if I explain it, go to printers and faxs on your pc find the oki icon for your printer right click it and propertys.... go to printing preference tab, look in there....

If you are having image problems with new drum, I doubt any reset will help.

Post back any issues or check link below chapter 5
http://my.okidata.com/man-8w.NSF/InsideUsersManual?OpenFrameSet

Nov 13, 2007 | OKIPAGE 8W Led Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

1,215 people viewed this question

Ask a Question

Usually answered in minutes!

Top OKI Office Equipment & Supplies Experts

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

386 Answers

Jimbras

Level 1 Expert

13 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you an OKI Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...