Question about Samsung Health & Beauty

1 Answer

Digital wrist model # SR303S, shows error 3, has new batteries

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Possible explanations and work-arounds based on various blood pressure monitors..net is if it has worked religiously like mine had and this error comes up, and the simple fixes below do not work, there is something internally wrong with the unit..there does not seem to be any customer reset or obvious fixes..contact the manufacturer for service..

Error Description Potential cause and remedy

«Err 3» No pressure in the cuff
An adequate pressure cannot be generated in the cuff. A leak
may have occurred. Replace the batteries if necessary. Repeat the
measurement.

---------------------------------------
Error Codes

Err 0 No pulse is detected
Err 1 Inflation rate is too low
Err 2 Systolic reading unattainable
Err 3 Cuff pressure is too high
Err 4 Diastolic pressure is outside of operation range
Err 5 Cuff deflated too fast
Err 6 Cuff deflated too slow
Err 7 Systolic pressure is outside of operation range
Err 8 Overall pressure is outside of operation range
Err 9 Cuff is unable to inflate to the necessary pressure level
--------------------------------------
Error No. Possible cause(s)
Err 1 No pulse has been detected. Cuff may be positioned incorrectly.
Err 2 The arm was moved during the measurement.
Err 3 Inflation of the cuff took too long. The cuff is not positioned correctly.

Posted on Jan 19, 2011

  • rick27607 Jan 20, 2011

    Just called Samsung customer support on this exact sr303s model and Err 3 issue and they said that this error occurs on this 'older' model when the batteries have been in the unit too long. They suggested taking the batteries out, let it sit for an hour (to possibly drain any residual memory effect that might be causing this error) and then put in fresh alkaline AAA batteries to see if it fixes it..if it doesn't there is no other troubleshooting that can be done. I also asked and there is no reset sequence either. As a side note, the batteries in my unit were on the border but not dead or leaking)..

  • David R Savage
    David R Savage Jan 07, 2017

    I have the same unit under discussion. I did replace the batteries and verified the memory was zero by pushing the MEM button. I kept using over a three day period a few times each day and it started working again. The error 3 states that the pressure is to high in the cuff. if the unit is filling the bag and depletes slow, it may not be a leak but a pressure sensor that may need to be used after sitting for a while as mine was. DR Savagd

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does error code EP


you should be able to clear the code by removing the battery, and by the way does it have new good batteries?

Nov 17, 2015 | Walgreens By HoMedics Automatic Wrist...

3 Answers

Alarm


that means your batteries are not charged fully. I'm assuming you have new fresh batteries? Does the panel stay up long enough to show the charge level?

Feb 16, 2008 | Samsung Digimax S630 Digital Camera

1 Answer

Wristech blood pressure Moniter Model # HL-168


1) Try to get the band as tight around your wrist as you can with the sensor part of the strap across your wrist nearest the palm of your hand, and try it again.
2) Try changing the batteries. They sometimes start to error like this before the batteries show as weak/dead.

Jul 03, 2014 | Health & Beauty

1 Answer

Showing ee in the diastolic section, therefore its not taking the b/p


There are 3 things can cause the EE error code.

1. Cuff was placed incorrectly. Wrap cuff snugly around your wrist 1" above the heel of your left hand.

2. Moving or talking during measurement. Measure again keeping your wrist steady during measurement.

3. Shaking of the wrist with the cuff on. Solution is the same as # 2.

If you continue to have a problem with the cuff, contact HoMedics Customer Support 1-800-466-3342.

I hope this info was helpful and thanks for choosing FixYa.

Sep 15, 2011 | Walgreens By HoMedics Automatic Wrist...

1 Answer

Walgreens digiital blood pressure monitor model HD303 keeps saying Error code 3 have put new batteries in the correct way?


Since that BP Monitor has a 5 year warranty. Your best bet is to contact HoMedics (the manufacturer) Customer Support @ 800-456-3342. That's assuming you replaced the old batteries with new one's out of a in date package and all are placed properly.

Apr 25, 2011 | Walgreens Wrist Blood Pressure Monitor

1 Answer

Gives wrong pressure readings. also shows only error on pulse. can be repaired or buy new one. if fixable where to send to


You didn't mention how long you've had this wrist monitor, but it may be a case of it not being used properly. For it to work best, you need to keep your arm/wrist still at heart level. Place the cuff on your wrist, at least 1" above the heel of your hand. Be sure the strap is fitted snugly ground the wrist before starting the unit. Then remain still. Don't flex or shake your wrist during the testing procedure. You may also need to change the batteries.

If none of the above solves the problem, most BP wrist monitors have a 5 year limited warranty (check your Owners Manual for yours) and will allow you to return to them for repair or re-calibration. But you must have their approval before sending it, as well as your Proof of Purchase.

Hope this helps you to solve the problem.

Mar 28, 2011 | Centrios Wrist Strap Blood Pressure...

1 Answer

I get error codes on the unit. Can you tell me what the error codes mean?


I AM GETTING ERROR 3 ON MY LIFESOURCE BLOOD PRESSURE MOINTOR 7 WHILEPUSHING ON START BUTTON,IT DOES NOT GO AHEAD MORE THEN FIGURE 2 & COMES BACK TO 1 & THEN SHOWS ERROR 3,CAN ANYONE,SUGGEST OR GIVE SOLUTION/REMEDY ON MY MAIL ID:hemant_pandya12@yahoo.com I HAD LOST OPERATING MANNUAL & WARRANTY CARD,ALTHOUGH THIS MONITORING INSTRUMENT'S HAVING LIFE TIME WARRANTY,INCLUDING CUFF. THANKING YOU.
H.M.PANDYA.

Mar 03, 2011 | Lifesource Digital Blood Pressure Monitor...

2 Answers

I have the Prevention wrist monitor WS820 What does the error code -3 mean?


Deflation Error - Movement or talking was detected during measurement.

Turn off the power and make another measurement while being quiet & still.

Aug 06, 2010 | Prevention Wrist Blood Pressure Monitor...

1 Answer

Err 3 is displayed


Wrist blood pressure monitors must be used with the arm above heart level. You can do the pledge of allegiance while doing a reading to make sure this is done. Usually this error occurs when inflation takes too long or the placement of cuff is wrong.

Sep 10, 2009 | Walgreens Wrist Blood Pressure Monitor

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

1,823 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Health & Beauty Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Md Fazlurrahman
Md Fazlurrahman

Level 1 Expert

23 Answers

Joe Ball
Joe Ball

Level 3 Expert

539 Answers

Are you a Samsung Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...