Question about Ricoh Aficio 1013F Copier

5 Answers

ERROR CODE SC101

RICOH AFICIO 1013 CODE SC101

I WAS SENDING FAX AND HAD A POWER OUTAGE. WHEN POWER CAME BACK ON, THE MACHINE SHOWED ERROR CODE SC101 FUNCTIONAL PROBLEM AND RECOMMENDS SWITCHING OFF MAIN POWER SWITCH AND ON AGAIN, BUT IT IS STILL GIVING THE SAME
ERROR MESSAGE. CAN YOU HELP?

Posted by on

  • roosey Feb 15, 2009

    Hi, I'v ricoh aficio colour 6513 copier and printer machine. I was printing, suddenly the machine showed error code SC101 functional problem and recommends switching off main power switch and on again. But it is still giving the same problems.

    Many thanks


×

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

SC101 indicates and exposure lamp problem. To try and correct, turn OFF the copier and then unplug from the wall. Wait 10 seconds and plug it back into the wall, then turn on the copier. Watch to see if the exposure lamp comes on - lift the document handler if you want. If the exposure lamp is working correctly, the scanner will briefly move to the right and the light will turn on then off after it moves to the left.

Posted on Jul 09, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Definition Symptom Possible Cause
SC101 Exposure Lamp Error
The scanner has scanned the white
plate, but cannot detect the white level.
• Defective exposure lamp
• Defective exposure lamp stabilizer
• Defective exposure lamp connector
• Unclean scanner mirror
• Scanner mirror out of position
• Defective SBU board
• Defective SBU connector
• Lens block out of position
• Incorrect position or width of white
plate scanning (�� SP4-015

Posted on Mar 14, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have this problem
i change the ccd but after 2 days sc101 comeback again

Posted on Apr 28, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

100/100 exposure lamp

Posted on Mar 11, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the similar problem with SC101 when dealing with AFICIO 700 and 650 unit. The exposure lamp light up but the scanne is not moving from to the right. Light then off. Can this be white level not detected - can it be solved easily by changing SBU (CCD) or cleaning exposure glass and the 3 mirrors to remove the static contents. Sill not working.

richard lim
richard8101194@yahoo.com.my.

Posted on Jul 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My aficio 1022 is showing code sc101. How can I fix it


SC101 is scanner home position error. Check the sensors or the white plate, usually its dirty.

Aug 13, 2014 | Ricoh Aficio 1022 All-In-One Laser Printer

1 Answer

How to check exposure lamp on ricoh sc101?


Clean the true white on the slit glass housing. Check for a dirty scanner mirror or that the scanner mirror is out of position. Also, check if the scanner is blocked or if the dirty white plate underneath the glass is obstructed. Try cleaning the glass with water. To reset this error try the code:

"Clear Mode"+107+"Clear/Stop" hold for 5s.

Turn ON and OFF the Main Switch.

Jul 15, 2014 | Ricoh Aficio 1013 All-In-One Laser Printer

1 Answer

Ricoh photocopier 1055 code sc101


for sc101
Exposure lamp error
The standard white level was not
detected properly when scanning the
white plate.

Dec 08, 2012 | Ricoh Aficio 1013F Copier

1 Answer

Ricoh Aficio 1013 error code sc 544


Fusing low temperature error

Symptom: Detected fusing temperature
remained abnormally low for 1
second during fusing operation
(below 140°C) or during standby
mode

Possible Cause: Fusing thermistor defective
• PSU defective
• Bad connection between fuser and
machine

Dec 18, 2010 | Ricoh Aficio 1013 All-In-One Laser Printer

1 Answer

I have a Nashua sc550 Aficio 1013. Its displaying error SC550. message displayed is "Functional problems, turn off main power switch then on again. If error reoccur, call service" Best regards


Your question is somewhat confusing as to the model. There is no Nashua SC550 as that seems to be the service code you have an issue with. There is a model 1013F but there is no SC550 code for that machine. That being said I will tell you what an SC550 code means on most all Ricoh, Gestetner,Nashuatec machines. The SC550 means your fuser oil/cleaning web life is over. The solution for this is to replace the web and then reset the counter which requires entry into the service mode. Both of these are going to require a service technician to complete.
Good Luck and Thank You for using Fixya.

Sep 03, 2010 | Ricoh Aficio 1013F Copier

1 Answer

Even though my RICOH Aficio 1013 appears to be an ALL-IN-ONE, the ONLY function it now porforms that of a copier. What components do I need to add or install to get to function as a printer, scanner, &...


It would be cheaper to find a 1013spf meaning scan,print,fax. Finding all of the boards, wiring harness, ROM chips and control panel buttons needed to convert your machine would be pricy. Then you would need a service tech to install everything as well. You can find the "spf" versions used for less than $1,000 and you could get around $500 for yours.

Jan 15, 2010 | Ricoh Aficio 1013 All-In-One Laser Printer

1 Answer

Am having ricoh 1013 photocopier, and its giving an error message that "functional error,switch off mainpower and on"!


Low fusing temperature. Either the thermistor is bad or power supply board (unlikely). Service code can only be reset in service mode by a technician after problem is fixed

Mar 24, 2009 | Ricoh Aficio 1013F Copier

2 Answers

Message SC101 Functional Problems


If the lamp does come on, remove the left side that holds the glass in place. It usually has the markings for where to place your origonal. Under it you will find a white strip of plastic tape, clean this. that is how it sets its lamp reference.This will usually work for a weak lamp.

Jul 07, 2008 | Ricoh Aficio 1035 Copier

4 Answers

Ricoh photocopier 1075 code sc541


Ok, its a firmware bug, but you should be able to reset it. Press clear modes, 1, 0, 7, and press and hold clear/stop. Press 1 for copy sp. Scroll down to 7, (data log) press 7. scroll to 7807, and reset it. exit all the way out, and recycle the power.

Mar 18, 2008 | Ricoh Aficio 1013F Copier

Not finding what you are looking for?
Printers & Copiers Logo

4,393 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Printers & Copiers Experts

quennie732

Level 2 Expert

393 Answers

Bernard D'Souza

Level 2 Expert

161 Answers

OfficeServiceAjnc
OfficeServiceAjnc

Level 2 Expert

181 Answers

Are you a Ricoh Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...