Question about Norelco Arcitec Electric Shaver with Jet Clean System - Gray/Black

1 Answer

Can the arm of the jet clean system be retracted into base for travel or storage

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes, after you push the start button on the unit, pull the plug out of the wall socket when the arm gets to its bottom position. It will stop at this lowered position. When you plug it in again, it will go back to its upright position. Norelco ships the new cleaning units in this contracted position. When you plug it in presto! You are ready to go.

Posted on Sep 25, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i clean my with my philips hq2000. instructions are in a different langue


  • 1 Set the Jet Clean System base on a flat surface and pull the cleaning reservoir out of the base.
  • 2 Unscrew the fill cap on the reservoir, pour Jet Clean Solution into the reservoir and replace the reservoir in the base.
  • 3 Plug the power cord of the cleaning base into and electrical outlet.
  • 4 Remove the protective cover on the razor head and place it to the side. The protective cover must be removed or the cleaning system will not work.
  • 5 Slide the razor head into the base, push back on the razor handle and press the locking lever down to keep it in place. The indicator light on the cleaning base will blink, indicating the razor is inserted properly and charging.
  • 6 Press the "On/Off" button on the side of the cleaning base. The razor will lower into the cleaning solution and begin the cleaning process, which takes approximately one hour. The razor will rise out of the cleaning solution when the cleaning process is complete.
  • 7 Lift up on the locking lever, remove the razor from the cleaning base and rinse the razor heads under warm water to remove any remaining cleaning solution. The razor is now clean and ready for use.

  • If you just have the solution and not the Jet Clean System, then I would presume you could soak just the heads in the solution to clean them and then rinse it off.


  • Jul 22, 2014 | Philips Norelco Hq200 Jet Clean Solution 2...

    Tip

    Improving Dishwasher Performance


    If your dishwasher is not getting your items as clean as you'd like, the problem might be in your sprayer arm jets. The jets are the small openings in each of the sprayer arms. Sometimes the food grinder doesn't adequately remove all the food particles and other debris and this is pumped into the sprayer arms. You'll need to remove the arms (usually just a simple removal of a wing nut) and flush them with a strong jet of water from your faucet or the sink sprayer. I've sometimes found pieces of paper from fresh produce, small bits of plastic or bone fragments, and larger pieces of food inside the jets. A tweezer will help you remove these from the jets, thereby opening them so that the water can again be forced through them. A wooden toothpick can also be helpful cleaning the jets.

    on Dec 02, 2010 | Dishwashers

    3 Answers

    Engine speed surges up and down


    Keith:

    First check for the obvious... fresh fuel? clean air filter? carburetor mounting bolts/nuts tight? cylinder head bolts tight? crank case bolts/nuts tight?

    Now to adjust the governor:
    Find where the governor shaft comes out of the engine... loosen the nut and bolt on the governor arm clamp (where the governor arm clamps to the governor shaft). Gently pull the governor arm back until it stops, Gently turn the governor shaft the same way (some have a slot for a screwdriver or a hex-head for a nut driver to hold the shaft at it's closed position) as you pull the governor arm. Both the arm and the shaft must be at their full stop of travel while you tighten the governor arm clamp. It may take another person to lend a hand to keep the governor arm at the closed position while you tighten the clamp.

    Nov 30, 2013 | Tecumseh Snowblower Snow Blower Starter...

    1 Answer

    I have a ge quietpower 3 dishwasher. Lately it has stopped cleaning the dishes. Sometimes the dispenser tray doesn't open. Sometimes it does open and the soap pac hasn't disolved.


    Make sure your water temperature is hot enough to dissolve the soap. Generally, the water temp. should be 140 degrees. Run some hot water at the tap before you turn on the dishwasher. This will assure that hot water is in the dishwasher as soon as you start it. Be certain that there aren't any large pieces in front of the dispenser tray. Sometimes casserole dishes, frying pans or baking pans can block the door and prevent it from opening.
    Also, the sprayer arms might be clogged with bone fragments, peelings, bits of paper, etc. If this is the case, you'll need to remove the sprayer arm, flush and then check the jets. If you see "stuff" in the jets, they can be remove with tweezers.
    Finally, make sure the upper sprayer arm hose is securely seated with the tube in the back of the dishwasher that carries the water up to the sprayer arm hose. If these two are not seated correctly, the water will not travel into the sprayer arm hose, the sprayer arm will not turn and your dishes will not get clean! I hope this helps. If it does, please come back to Fixya and rate my advice.

    Jun 10, 2011 | Maytag Dishwasher

    1 Answer

    The dishes on the top rack are not cleaning at all. The sprayer arm is not rotating. The jets are all clear of debris. And of course, warranty just out.


    Hi


    Please check if something is blocked near the top spray arm, also make sure that all holes are oopen. Use a sharp metal pin to clean the holes on the top spray arm. Make sure the water pressure is not low.

    under the screen and youl'll need a Torx driver to get to it after you remove the spray arm and screen. Check to see that the path it travels is clear. I have seen these get blocked up by stuff.

    Now check if the top arm spins freely and check the bearings for the arm, if they are producing extra friction while the spray arm spins. Hope this helps... Please post back if you need more assistance.


    Dec 13, 2010 | LG LDF6920ST Stainless Steel 24 in....

    1 Answer

    Lost directions on how to use jet clean system. Do not know how to use it.


    Visit this site below and enter your product number. If you don't have your product number or it doesn't appear, then type in "jet clean" then scroll down and click on personal care. You can then click on a jet clean model and then open the .pdf of the manual. The instructions should be similar. There is nothing to using it. Fill the reservoir with jet clean solution to the max line. Put the shaver in the cradle heads down and press the button on the front of the cleaning base. If it doesn't stay down and clean you may have another problem. If so, then search "Norelco Arcitec Electric Shaver with Jet Clean" on this site and you can find answers to your problems.
    http://www.support.philips.com/support/sms_page.jsp?userLanguage=en&userCountry=us

    Jun 09, 2010 | Norelco Arcitec Electric Shaver with Jet...

    2 Answers

    Adjust travel of wiper arm on 2001 vw jetta


    Adjusting for more or less travel isn't possible , but you can remove the arm off the stem and reposition it slightly to improve windshield coverage... Remember you only need to move it a little bit.

    Nov 20, 2009 | 2001 Volkswagen Jetta TDI

    1 Answer

    My maytag will not clean the dishes. I have cleaned out the water tubes, I have checked the hot water. all it does when you run a cycle it leaves the dishes dry and the detergent is not being used.


    Most likely causes are:

    Not enough water entering dishwasher (check level after fill... Should be slightly below bottom wash arm)

    Water filling but draining during wash cycle. Check toward end of wash cycle but before drain. See if water level is diminished from start of wash cycle.

    New 'water saver' dishwashers are notorious for having smaller water jets, and thus easier to stop-up jets. Check the jets on all wash arms to be sure they are cleared of food particles.

    Another way to check the wash arms is to manually position them at specific locations, momentarily run the dishwasher for a few seconds, then open the door to inspect the location of the wash arms. Do this three or four times to eliminate the possibility of coincidence.

    If the wash arms do not move from the location that you put them, the most likely cause is food particles stopping up the water jets. These jets not only clean the dishes but also the water pressure they generate turn the arms inside the dishwasher to properly distribute water pressure on the dishes.

    Sometimes you can dislodge and remove food particles stuck in one of the jets with a toothpick or other small probe. Others require that you remove the arm(s) and get a little more creative. I use compressed air to clear mine, but not everyone has access to compressed air, so use whatever you can to remove the food particles.

    Simply dislodging them from the water ports is usually not effective... As soon as water pressure is applied, the particles return to the jets and stop them up again. The real fix in this instance is to completely remove the food particles from the arm if you can.

    Hope this help. Good luck.

    Sep 11, 2009 | Maytag 24 in. MDB8600AW Jetclean II...

    1 Answer

    I have a mdbd880aww model and it seems that the


    The pump and impeller needs cleaning or replacing.
    Remove the spray arm and base to access the impeller and pump inlet for cleaning and inspection..

    Mar 26, 2009 | Dishwashers

    1 Answer

    EXTRA BASE


    babies r us has the bases they are genric and work for a cuople different travel systems the sales person was super helpful and we love having the second base so there is no installing of the seat from my car to my husbands it just clips right in.

    Jan 10, 2008 | Eddie Bauer Lightweight Travel System...

    Not finding what you are looking for?
    Norelco Arcitec Electric Shaver with Jet Clean System - Gray/Black Logo

    Related Topics:

    105 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Norelco Health & Beauty Experts

    shaveroutlet.com
    shaveroutlet.com

    Level 3 Expert

    1610 Answers

    Bruce Foote

    Level 1 Expert

    33 Answers

    Kazim ERGUNEY
    Kazim ERGUNEY

    Level 3 Expert

    577 Answers

    Are you a Norelco Health and Beauty Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...