Question about Dremel Variable - Speed Multipro Rotary Tool 395

1 Answer

I have read the solutition that has been presented about brushes getting too hot and sticking. one skides out easy and the oppisit side is frozen and does not come out. with it's hard to get a tool in and try prying it out without damaging the holder, how do i get the stuck brush out of the plastick holder please ans ed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Dremel Master
  • 885 Answers

You have to split the case and remove the entire switch/brush holder from the tool. You can use anything from picks to files to drill bits to get all of the stuck brush material out of the switch. Small files help clean up the holder area. Just be very careful not to damage or break the switch, they have been discontinued and are getting exceedingly hard to find on after-market parts sites. Depending on which version 395 you have, switches are available for a couple of them at www.ereplacementparts.com. The different versions have a number like F0130395XX, where the XX is different for each model variation.

Posted on Jan 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kitchenaid frozen bearing


Hi Thaddeus, What model is it? If you have taken it apart and checked the worm gear surely you would have stumbled on the frozen bearing if one exists. When you split the gear cases you are in a position to turn everything by hand so any frozen part is going to be pretty obvious.
Cheers Ross

Apr 24, 2016 | KitchenAid Food Mixers

1 Answer

Rear end seems like its slipping


it mite have a axle seal leaking or a wheel cyclinder mite be leaking causing the brake shoes to grab and stick ,

Jul 13, 2012 | 2005 Dodge Ram 1500

1 Answer

Changed the O rings now the hot and cold water are on the oppisite sides


You got the water lines switched up when you reconnected them below the sink.

Jim

Sep 11, 2010 | Moen 7310 Legend Single-Handle Kitchen...

1 Answer

Can you reverse the door on the front load washer?


yes u can you will see some small plasitc pieces covering the holes on the oppisite side remove these plastic peices gently u willneed to use them on the oppisite side remove the door and the latch assembly u will see the same holes on the oppisite side make sure you install allthe plastic cover pieces back into the unit if not this is a great place for bugs to hide

Jul 18, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Change Door


there should be two plastic covers or two screws on the oppisite side.simply unscrew the hinge from the side its on flip the door the oppiste way.remove the door mechanism that is on the frame and put the mechanism onthe oppisite side and rescrew the hinge on the oppisite side

Apr 28, 2010 | Whirlpool GEW9250 Electric Dryer

1 Answer

Ge side by side refrigerator


I oftenlly have to clear drains so it depends on the circumstances. If the hoemowner has laminate tiles or nice hardwood floors i try to advoid hot water. It will make the floor come up. Hot water into a frozen drain does the trick nicely though. That side by side you have should be easy to get to after you remove all the bottom foods. You probably dont even have to take out the back panel to get to the drain. With less mess use a hair dryer. If it is not frozen but has foods debris try top blow the drain with compressed air. if you dont have that use a 3/16 clear hose and stick it in the drain and blow. when the water goes down (pour a cup) then it is clear. get a mop and rags ready for overspill. hope this is helpful

Mar 29, 2010 | GE (PSS26MSRSS) Side by Side Refrigerator

1 Answer

Temperatue gauge reading hot and car is cold


May be the thermastat. Some of them stick open, and some stick shut when they malfunction. Most stick open and don't allow the car to heat up to operating temp, because the coolant is running through unchecked. If it sticks shut, you cannot get coolant to circulate the engine and cool it down.
If it reads hot when first starting it, and it is obviosly cold as ice cubes, then the enigine temp sensor is busted. These can get too hot, usually from improper installation of leaving off the heat shield, and break. If you can find it(use a repair manual), it should be an easy fix.

Jan 15, 2010 | 2003 Chevrolet Impala

1 Answer

Not keeping meat completely frozen.


the seal around the freezer is always hot, that prevent humidity around the seals and avoid it gets wet, now u have to check the low pressure side of ur refrigerator just to be sure that ur refrigerator is not running low r134 charge, try to use a brush to clean the condenser unit in the back of ur refrigerator and clean the coils... otherwise i suggest to call a technician !

Mar 15, 2009 | Hotpoint HSS25GFP Side by Side...

1 Answer

Roper frig, freezer on top ,frozen under tray.water in bottom of frig


sounds like you have a frozen defrost drain. This is a fairly easy repair you can do yourself. 
  • Unplug refrigerator
  • unload food from freezer
  • remove icemaker if present (there are 3 screws remove the one on the bottom and loosen the 2 on top of icemaker then lift it off the 2 screws unplug from wiring harness)
  • remove 2 screws holding rear cover in place
  • move cover to the side or remove from unit altogether
  • defrost any and all ice from bottom of freezer and aluminum drain pan that is now exposed
  • flush drain hole that you will see once ice is cleared with warm water. (sometimes I use a large syringe or turkey baster to forcefully flush hot water thru the drain tube)

that should fix you up. if you have any further questions leave me a comment here and I'll gladly help any way I can. thanks Peytonreassemble in reverse order

Feb 23, 2009 | Whirlpool Refrigerators

1 Answer

Yellow flashing triangle


The yellow flash triangle comes up when the car attemps to skid. it simply prevents the car from skiding off the road.

Nov 15, 2008 | 1994 BMW 3 Series

Not finding what you are looking for?
Dremel Variable - Speed Multipro Rotary Tool 395 Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dremel Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Mike

Level 3 Expert

4336 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...