Question about Nokia N95 Cellular Phone

2 Answers

N95 8gb cycles on off on off on off on off every 40 secs

Posted by on

  • 1 more comment 
  • bhfm Jan 03, 2011

    phone is not ON long enough to get to reset......

  • bhfm Jan 16, 2011

    Reset is done and so far.............................. M95 8gb is working after 5 mins. I will let you know what has happened in a day or 2

    daveb

  • bhfm Jan 18, 2011

    Previously the phone has worked for an hour or two ,but now thankyou rajdeepdutta it has been OK for 3 days it looks like it's FIXED

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 944 Answers

Hi,

This is due to your phone firmware is corrupted due to virus.You need to reset the phone firmware,
You can do it by master reset.Since you say it on/off/on/off then you can't follow the procedure.
You have to flash your phone.I recommend you can flash your phone when it normal dead state.But this on/off/on/off is not a normal behavior.While flashing it should not have any disturbance if its going to have then phone will be useless anymore.So i prefer you to take to the service center to flash it.

Steps how flashing does.
ForCDMA:If your mobile is CDMA you have to flash you mobile,to get itworking.Flashing is a process by whichyou erase the software of your phone and install new firmware so all the details get erased,so the code and allthe details in the phone will be erased.Flashing is a risky,You have to follow predefined steps verycarefully. The stepsfor flashing any mobile is given in the below link as a video please followit correctly. http://hubpages.com/hub/How-to-Flash-your-cell-phone Note:Ifthe flashing stop inbetween at any point during the process,the phone iswaste,you can't use it more.If you feelyou have some hand's on you can do it.else please got the nearest service center and ask him do it.Itwill cost very less and may vary according to the phone.
Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thank you for using fixya have a nice day:-)

Posted on Jan 04, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nokia Master
  • 2,517 Answers

Hi there reset the phone factory setting from setting option. use 12345 password. Let me know.

Posted on Jan 03, 2011

  • 3 more comments 
  • RAJDEEP DUTTA
    RAJDEEP DUTTA Jan 12, 2011

    I hope your problem is solved. Just waiting for reply from you .

  • RAJDEEP DUTTA
    RAJDEEP DUTTA Jan 16, 2011

    OK. I understand the problem. Its a phone operating system corrupt. Try these which you can done in 4 sec. Try these and let me know.
    Press *#7370# then press YES. Its reset your phone very first. No need to go in option. During reset the phone its automatically Turn off and take few minutes for turn ON. So please wait and see. Let me know the result please.

  • RAJDEEP DUTTA
    RAJDEEP DUTTA Jan 17, 2011

    Waiting for your reply.

  • RAJDEEP DUTTA
    RAJDEEP DUTTA Jan 19, 2011

    Grete . I hope you happy with my suggestions. Please accept my answer and share me a rating.
    Thanks.

  • RAJDEEP DUTTA
    RAJDEEP DUTTA Jan 22, 2011

    Please accept my answer so that i can pay from you. As per your information your phone working now. Waiting for reply from you

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my cme306 scotesmen go into the harvest cycle in just 40 sec. of starting up


The first thing it does after a failure or power disruption is go into a harvest cycle.It will be a prolonged cycle at the first start . then it should operate normally

Jun 28, 2014 | Scotsman Cooled Modular Contour Cuber Air...

1 Answer

Flame turns off rematurely


That is normal. The gas does not stay on constantly. That would burn the clothes. The gas assembly is controlled by a Klixon mounted on the blower housing. As the air comes through the blower The Klixon also known as the cycling thermostat judges air temp and turns the gas assembly on and off. Here is a video explanation:

Jul 20, 2012 | GE Dryers

1 Answer

Blower vac runs a few sec. then stops


Check age of gas. Cannot be more than 30 days old. Make sure to use fresh gas w/synthetic 2-cycle oil @ 40:1 ratio (1 gal.) Gas to 3.2 oz. Oil). Do not use old or stale oil/gas mixture. Always use the proper oil/gas mix. If you do not, your engine will suffer rapid, permanent damage. May need to clean or replace carburetor.

Aug 24, 2011 | Craftsman Garden

1 Answer

I can't figure out how to set seconds on the microwave. Please help the manual was no use!


Sorry to read about your problem, I hope this helps you out.

just hit 10 for 10 secs or 40 for 40 sec..up to 60 secs

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

Dec 25, 2010 | Cuisinart CWM-100 Microwave Oven

1 Answer

My miller matic 35 welds and stops after about 2 inches let cool for about 30 to 40 sec and it welds again. fan runs


these need a good power supply , i looked and did not see the duty cycle on this welder if you are doing heavy welding 100% power it will need 30- 40 minutes to cool of to weld again. it all depends on the units duty cycle, stated on the welder spec plate ..can you bypass the auto feed speed mode ? this might be the issue.. good luck ..use all the protection you can when welding these are like the sun and can and will burn exposed skin and eyes .. if'n i was any help throw me a bone and vote thanks jay

Jul 28, 2010 | Miller MATIC 140 MIG WELDING PKG w/cart...

2 Answers

Goodman gmp075-3 gas furnace and the flame cycles for 4 sec


JUST SAND THE FLAME SENSOR LOCATED IN FRONT OF THE LAST GAS PORT.

Dec 02, 2009 | Goodman GMS90703BXA Heater

2 Answers

HOW TO PROGRAM 2003 TOYOTA CAMRY FACTORY REMOTES


1. Driver door open and unlocked. Key out of the ignition
2. Insert the key and remove 2 times in 5 sec.
3. Close and open driver door 2 times in 40 sec.
4. Insert the key and remove it again from ignition.
5. Close and open driver door 2 times in 40 sec.
6. Insert the key in ignition,
7. Close the door,
8. Turn to on and back to lock in 1 second intervals. 1 time for add, 2 times for rewrite, 3 for confirmation 5 for prohibition. (yes, there is no “4”)
9. Remove the key
10. Power lock will cycle to confirm
11. For add or rewrite mode within 40 sec of the confirmation,
A. press “lock” and “unlock” buttons of the FOB at the same time between 1 and 1.5 seconds.
B. within 3 sec press “Lock” button for more than 1 sec and release.
C. If it’s correct, the power door lock will cycle once. If it’s wrong the door lock will cycle twice.

Sep 17, 2009 | 2003 Toyota Camry

1 Answer

How can I re active the wireless remote control system ?


sit in car all doors closed put key in ignition and turn from OFF to ACC 3 times as fast as you can leaving it in ACC on the last cycle then press your remote button. your blinkers should flash to tell you this has worked.... may take you a couple of tries to get it!!

Jun 30, 2009 | 2002 Toyota Camry Solara

3 Answers

GWL10 US won't finish cycle


Hi Mate, I had the same problem and then looked on the web to find that all I need was a $40 out of balance switch. Although the old one looked ok it had corrosion inside, bought a new switch and installed it myself, easy, ask the F&P parts supplier if you are not sure.
Cheers,
Dan

Jun 26, 2008 | Fisher and Paykel IWL12 Top Load Washer

Not finding what you are looking for?
Nokia N95 Cellular Phone Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nokia Cell Phones Experts

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18387 Answers

IT Solution
IT Solution

Level 3 Expert

805 Answers

Are you a Nokia Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...