Question about Audio & Video Receivers

1 Answer

The light on my CD player is on, meaning there is a CD in the player. There is no CD in the player though. You can't put another CD in the player, and nothing will eject from the CD player either. Is there anything I can do to fix this?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Nothing you can do about this. It is the IC on your CD player that reads the wrong signal. The best way to fix this is to have a technician who knows to reprogram your IC.

Posted on Jul 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cd won't turn or makes clicking sound when turning. Either way won't play


Remove the cd then.
remove the cd cover then
tutn on the device without cd and look at the cd reader if there is red light. If so turn the potentiometer installed with th cd reader board a little bit in one direction and notice the light.if mire light came on put the cd and test
if not ok replace the cd reader
if the light decreased when you turned the potentiometer . Turn it on the other direction carefully untill there is more light

if there is no light from the cd reader. Unplug the cable installed in it and clean the terminals carfully with suitable cleaner then plug and test . And if still no light . Change the cd reader

nnote. Usually its a cd reader fault

May 07, 2015 | Bose Awrc1g Wave Radio Cd Player Only -...

1 Answer

CD player displays error code: ER-1


That error code means an unknown error has occurred. Try cleaning the player itself, along with the CD's prior to insertion to see if that helps.

Feb 02, 2014 | Dual XD1228 CD Receiver

1 Answer

CD'S ARE ENTERED IN THE TRAY AND WHEN CLOSE BUTTON IS PRESSED IT DOES NOT SELECT ANY CD AND TRAY CAME OUT AGAIN. MEAN IT DOES NOT PICK THE CD


Does this happen on all cd's you try? Are these original cd's or burned copies? Many times burned copies will not work in certain players, it depends on the formats your player is capable of reading. If the player can not read that particular format it will reject it. Another thing to look at is to make certain there is nothing in the player that shouldn't be there, with the player open flash a light inside to see if there is anything stuck inside. Just a couple of things to try, hope this helps solve your issue. Best of luck.

Feb 18, 2011 | Audio & Video Receivers

1 Answer

Put a CD in and get message that says ER (Error?)...every CD that goes in spins, but does not play.


could be one of 2 things
use a cd lens cleaner to clean the laser lens .
or could be warped or damaged cds and player wont play them
also if they are burnt cd the player may be to old to read them.

Apr 26, 2009 | Audio & Video Receivers

1 Answer

My CD player says there is a CD player in the player, but there is no CD in there. You can't put another CD in there and nothing will eject. What can I do to fix this?


There is a problem in the way the connection of your cd player or on the chip of your cd player because it now reads the wrong signal. The best way to fix this is to rewire and reprogram the chip. Have technician in your area fix that.

Jul 09, 2008 | Audio & Video Receivers

1 Answer

Peugeot 406 cd player works when ignition is on but when engine is started cd player wont work. Radio is fine.


Just bought 2001 peugeot 406.The radio worked perfect but CD player not reading disk or operating.That was until I realised that the CD for driving safety will not allow you to put CD into it while driving or engine running.Switched off engine then switched it to 1st batt light position & CD worked perfectly.But when I then switched key off & then started it was back to not operating.I then realised that the CD player for safety will not operate when engine is running unless you let the CD start operating first pre engine fire then wait a little more time before starting .Now it should work properly though it will not allow even the passenger to change a disk while being driven. On disk change you have to go through the same start proceedure.Hope this will get your CD working.Sherlock ??

Jun 29, 2008 | Audio & Video Receivers

2 Answers

Much loved old J.V.C. unit


Sounds to me like the belt drive is slipping!
Need to open her up and check tightness of belt and probably try to buy another one which will be tighter!

Mar 21, 2008 | Audio & Video Receivers

1 Answer

PACKARD BELL CD/RADIO/MP3 PLAYER. MODEL PB OP 10


This is not for connecting an MP3 player, but rather for playing MP3-CD's. Using your computer and a CD burner, you can burn a CD with up to about ten hours worth of MP3s on it. The procedure for creating the disc varies depending on your burning software. In Nero, for example, you would select "Music" and then "MP3 Disc" and then select the songs you want to put on the disc. For other software you just select "burn a data disc" and then select the MP3 files you want.

Once you have a CD full of MP3s, put it in the Packard-Bell stereo's CD player, and you will be able to play all the MP3 files that are on the CD. THe advantage, of course, is being able to put ten hours on one CD instead of only 80 minutes.

Feb 13, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...