SHOWS A MESSAGE E 7 - Heating & Cooling

xp and 7 dont work well together,the file is damaged d/l a new one

Copied
1) - Power ON printer while holding both the + & - buttons until "OKIUSER" message appears in LCD.
2) - Press + or - button until "ENGINE DIAG MODE" is displayed.
3) Press "ENTER", displayed will be "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or - button until "NV-RAM INITIAL" is displayed.
Half way, dont stop too long it will time out....
5) Press "ENTER" again.
6) Will appear "TABLE 1" message.
7) Press "ENTER" until "EXECUTING RESET" message appear. ...............the "NV-RAM INITIAL" message will BLINK.
Tada....This procedure reset TONER, DRUM, FUSER and BELT...life counts
8) power OFF printer, wait 10 sec, and power ON again..

To access Service Mode in C9300 power ON printer with 0, 1, 6, 7 at same time...you can do some good damage in there!! (I warned ya!)

Resetting consumables for OKI C7300,C7500,C9300 printer I think!

1. Hold buttons 0 + 1 + 6 + 7 on startup.

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows.

3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

4. Press button 1 to scroll to "COUNTER SET".

5. Press button 2 to scroll through menu items (button 6 scrolls backwards)

6. To alter the value of an item, first press button 3 to select the digit to be altered. The selected digit will slowly flash. (Button 3 moves to the right through the digits. Button 7 takes you to the left.)

7. Then press button 2 to increase the value of the selected digit. Press button 6 to decrease the value.

8. When the changes have been made hold buttons 1 + 3 + 5. The screen will flash three times and then an * will appear on the right of the screen. The new value is set.

9. To leave the counter set menus, turn the printer off.
IMPORTANT

Each colour toner counter shows life as percentage used. So a toner showing 30% has used up 30% of its toner. 100% would indicate a near empty toner. This is the reverse of the toner life shown from the "usage menu" when the printer is in normal operation, which shows the toners as a percentage life remaining. You will want toner showing 00%. note:this is oposite of what you see in user mode
Some models exhange these steps

3) HOLD 0 + 4 "ENGINE DIAG LEVEL 2" shows

4) Press 1 to cycle to "fuser unit"

5) 2 to scroll to TONER

REST IS SAME WE WANT TO SET WHAT i GUESS IS AT 100% TO 0%.

You can try using a file recovery software like Bad Copy Pro 4.10.125. It works well for me.

If you are using the same battery, it could be it has reached the end of life. The charger can indicate the battery is fully charged, because the voltage has reached a correct level, but still the battery can have one or more bad cells. So as soon as you start using the battery, it can lose enough energy to give this nasty message. If you put in another battery and still have the same message, there must be a serious problem in the camera.
To check your battery, just after the camera has given this message, with a multi meter. You will see the voltage has dropped at least 1,2 volt beneath the voltage printed on the battery. The typical 7 volt Nikon battery, will give 8 volt on the multi meter. But placed in the camera it will drop to 7 volt. If the multi meter reading is less then 7 volt it has at least one bad cell and should be replaced.

Using window 7 scanner driver and try again

You will need to activate your copy of Windows 7. Once this is done this message will dissapear. If the activation fails then this means that you may be a victim of software piracy, contact the microsoft support center an Microsoft.com

i am usin a nvidia vga card and windows 7 64bit version
when i try igi it shows a error message couldnt flip
directx error
how can i fix this problem??????

in spam the message will shows wit the count so check it out

Hello,
Since the 2nd Button works press [2nd] [MEM] [7:reset] [F1][All ram] [ENTER]. That may help

Fiend your solution direct from Lexmark. Here is your solution



http://www.lexmark.com/printer/prob676ijt65/solution
893