Question about Kohler Electrical Supplies

1 Answer

After 8hrs of continous operation it shuts off and shows a aux/fault light on the display panel. Then has to be restarted and will run 8 hrs then trip again. The problem is it is a remote site so having to drive out & restarted it is difficult at best.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Aux fault is caused by a momentary loss of voltage from the speed sensor or low coolant level sensor. I would suggest you investigate both for possible cause.
If the unit has a low coolant level sensor you can find it near the top of radiator, small two wire plug. Disconnect and see if unit runs. make sure radiator is filled to over flowing before testing to eliminate this as the cause. Just because you can see or feel the coolant is not enough, fill to overflowing is the key.

Posted on Jan 04, 2011

  • Edyson Buri
    Edyson Buri Nov 16, 2013

    I have same problem thanks ..I'll check it thanks so much

  • Edyson Buri
    Edyson Buri Nov 16, 2013

    I would like to ask you about positio of speed sensor..thanks



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I was attempting to perform a system restore. I accidently powered off my laptop and now it continously restarts and shuts down in a continous loop. I am using Windows 8 and have a Aspire E1 522-5603...

take the battery out after that then press the power button for 5 secs. and then wait like 10 secs. then put your battery back in and restart see if it still loops it should fix it.

Oct 04, 2013 | Acer Computers & Internet

1 Answer

A/C runs fine for 7-8 minutes, then shuts off.

4 - 12
1. Indoor unit
(AH-X18MEV, AH-X18MEV-1, AH-X24MEV, AH-X24MEV-1)
To display the self-diagnosis, hold down the AUX button for over 5 seconds on the indoor unit when the indoor unit is not operating.
• The operation lamp (red), timer lamp (orange) and Super jet lamp lighter) flash to indicate the information of malfunction.
(Display of self-diagnosis result)
The operation lamp (red) and the Super jet lamp (green) flash in synchronization with the timer lamp (orange).
(AH-XP18MV, AH-XP18MV-1, AH-XP24MV, AH-XP24MV-1)
To display the self-diagnosis, hold down the AUX button for over 5 seconds on the indoor unit when the indoor unit is not operating.
• The POWER CONSUMPTION indicator indicates the information of malfunction by showing the main category error (number) and the sub-category
error (-number) alternately in 1-second intervals.
Example: Compressor high-temperature error

May 11, 2013 | Sharp Heating & Cooling

1 Answer

I am contineously getting indication of E8


It seems to be a connectivity failure between the Control PCA and Panel PCA or the joining cable is at fault. Please confirm the make and model of the scanner in order to provide you the exact solution.


Jun 06, 2012 | Office Equipment & Supplies

1 Answer

I have a Jandy Aqualink RS8 Wireless One Touch system that is not operating right. Auxiliary 3 is not working at all. Each time the filter pump automatically begins, three other auxiliaries (5, 6 and 7)...

Yes, you can just replace the board.
There are internal signals generated by the cpu board that open and close your aux relays.
With this type of failure (multiple aux's tripping at same) it is always just a board problem.
You will want to recheck all the wiring before installing new board to ensure that a short is not being created due to a bad connection.

Oct 29, 2010 | Jandy AquaLink RS OneTouch RS8 Pool or Spa...

1 Answer

My copier AR206 comes ON but display L then 6 continously

An L6-10 (if you hold down the start button the remaining portion of the fault will show up) fault means the polygon mirror in the laser unit has failed. Try shutting the unit down/unplugging it for 30+ seconds. If this does not reset the fault, you will need to have the laser unit (the LSU) replaced by a trained copier technician.

Sep 25, 2009 | Sharp Office Equipment & Supplies

1 Answer

GE Arctica intermittant clicking sound, panel flashes "hrs"

It sounds like the main control board is going bad . This controls every part on the fridge , except for the light bulbs . It's located on the back of the refrig , behind an 8" X 10" panel , with about 11 screws , holding the panel on . Part number WR55X10656 .

Sep 16, 2009 | GE GSH25JFR Side by Side Refrigerator

1 Answer

Runs fast, only 5 hrs recorded on 8 hr tape. Any speed setting

check that you have the right type of tape, SRC-800's should record 8HRS with a T-160 tape.

May 08, 2009 | Sanyo SRC-800 VCR

1 Answer

Windows Installation on Dell GX150 PC it took more than 10 hrs.

by the sounds of it your processor which is the brain of your computers is damaged you can either replace the motherboard of purchase a new computer because 8hrs is a long time for a installation

Mar 13, 2009 | Dell OptiPlex GX150 SF PC Desktop

1 Answer

My pc is restarting automatically continously when i turn on my

Does it show BLUE Screen, or does it show the Windows loading before it restarts?

If Bluescreen, something happened to root system files and you need to REPAIR
1. Shut down PC, pull out all USB devices, Floppies and insert Win CDROM
2. Power on
3. Press any key to boot from CDROM
4. Select Install
5. Select Repair
6. Ans questions and let run 30min
7. Remove CDROM
8. Reboot - it should work now

If Windows Logo, A device or driver you or MS or Mozilla or... installed for you malfunctioned and you need to start in LAST KNOWN GOOD mode
1. Reboot
2. Press F8 and hold down
3. Enter Password if asked
4. Select "Last Known Good"
5. When stable and logged in, Reboot

Jan 18, 2009 | Microsoft Windows XP Home Edition

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kohler Electrical Supplies Experts


Level 2 Expert

153 Answers

John Trevino

Level 3 Expert

1388 Answers

Wayne McNeil

Level 2 Expert

168 Answers

Are you a Kohler Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides