Question about Heating & Cooling

1 Answer

The conair cs36r doesnt heat up when connected

Posted by on

  • Anonymous Sep 15, 2008

    The light keeps blinking, but the heater pads dont heat up at all.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

You can call 1-800-3-conair . The cs36r has a 2 year warranty. Even if you do not have a receipt, they can use the manf date on the silver prongs on the electrical plug (4 digit date code). If this is within 2 years, you can return it after obtaining a return service number. i had to send my daughter's back after only 8 months. They answered on the first ring and within 5 minutes I had the number to send it back. There is a $3 charge for the return shipping. Hope this helps anyone out there with the same problem.

Posted on Apr 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting E1 error - Loss of communication between the single zone LCD thermostat and the module board. Manual doesnt give a solution or fix.


unplug cable at both ends. remove cover from t-stat. using contact cleaner spray contacts on cable and points it connects to. if necessary replace t-stat and cable

Aug 19, 2015 | Dometic 3313192.000 White Single Zone LCD...

1 Answer

My acworks fine when i switch to heat blower comes on but heat doesnt also no 24 volts on contactor in heat


Is this an electric furnace using heating strips as the heat source?
Or is it a heat pump system?

Nov 30, 2014 | Heating & Cooling

1 Answer

Amana heat pump doesnt come on.


sooo many possibilitys. turn it to heat NOT EM HEAT. usually a low voltage issue. unless experianced i say leave this one to the pro's

Feb 19, 2014 | Amana Heating & Cooling

1 Answer

Installed new thermostat and the heater doesnt turn off!


check for bare spots on the wires you connected in the thermostat. most of the time your looking a short from r-w1. did you get the right t-stat. there are different some are for gas heat some are for electric some work both

Oct 14, 2013 | Heating & Cooling

1 Answer

Conair mini split heat pump isn't cooling but has cold suction line but warm liquid line and is not freezing up the evaporator. Thinking a sucking reversing valve?? What could cause that? Both evapor


Make sure that your refrigerant charge is good first. Reversing valve has 4 pipes coming off of it. The one alone is discharge and centre of 3 is suction always. The two sides are the reversing pipes. One side should be same temp as discharge and other same temp (+-5F) as suction. If not then you have bypassing refrigerant in valve. Bad.

Jul 13, 2013 | Heating & Cooling

1 Answer

Conair portable aircondioner manual


Try this site:

http://www.conair.com/cnt_ib.php?action=filter&type=category

Jan 23, 2013 | Conair Heating & Cooling

2 Answers

I have a 5 ton goodmsn heat pump it only blows cold air the heat doesnt come on have a new heat strip in it but still blows cod air


Heat pumps require a reversing valve for heat operation on the outdoor section, a control signal to a "O" terminal or orange wire is required for heating and cooling depending on the thermostat and out door unit requirements. The thermostat also has to be heat pump type for the system to operate heat for electric system with heat strip, two stage electric heating.

Jan 31, 2011 | Goodman CKL60AR60 Air Conditioner

1 Answer

Gas furnice will run but doesnt seem to ignite...no flame burning! but it does run an doesnt blow heat?


check the ignitor if this unit has one...have a volt meter ready.unplug unit and unplug the ignitor place the leads to your meter in the ignitor molex plug one lead in each hole of the molex plug. turn the unit back on with power restored the small enducer draft motor should come on and then activate the pressure switch which has a hose connected to it. once it activates should send power to ignitor ..fi you are getting power but the ignitor is not glowing when connected then you have a bad ignitor. you did not post model mut if it is gas unit it will have either a ignitor or a pilot assembly... if it is a pilot assembly repost and one of us will be glad to walk you through checking it...good luck to you

Jan 13, 2011 | Heating & Cooling

1 Answer

My furnace is running but i don't think the main blower is kicking on, does it have its own fuse or a reset. I think its a conair but dont know where to look for model #


Usually the newer heaters have a heat exchanger temp sensor, this tells the fan to com on when the heat exchanger is hot enough, some models have just a timer, you will need to see if you are getting power to the fan. have a qualified person check your system.

Jul 25, 2010 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2028 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Cris Sparks
Cris Sparks

Level 2 Expert

338 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...