Question about Heating & Cooling

1 Answer

Dyna glo RMC 95 C6 kerosene heater, BRAND NEW. Wick and flame seem very low. At Max the wick height is 3/8(suggested height by manufacturer), flame is quite low, and not very hot at all

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1. Check to make sure you using fresh clean kerosene fuel. 2. Make sure you fill the heater and let it set for at least an hour, 2 hours is better. 3. If either of those solutions don't fix the problem, return to the store.
I have the same heater and just changed the wick. When working correctly, it should be so hot that it's uncomfortable to hold your hand 2 feet over it.

Posted on Jan 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to see pictorial instruction on how to replace wick in a Dyna Glo RMC-95-C2 kerosene heater


I think the Dyna-glow RMC95 series of heaters are equivalent to DH2300 series heaters.
In any event, the wick you purchased should have ahd the installation instructions included with the wick.

If it didn't or you tossed it, Here's a link to the DH-2300 series heater's Owners Manual, which may help you.

http://www.yourheater.com/DH2301-3%20owners%20manual.pdf

Good luck. Be sure to wear rubber gloves when you try to install the wick. Particularly, if you still have kerosene in the tank.

Feb 11, 2011 | Dyna-Glo RMC-8001SS Heater

2 Answers

I just replaced the wick, cleaned up the heater and filled with new K-1 kero. The heater (Dyna-Glo RMC-95-C7) is emitting black smoke worst than ever. The wick is burning a little unevenly.


Either the wick was improperly installed or you may not have allowed enough time for the wick to soak in the kerosene and become evenly distributed. Check the placement of the new wick and allow time (several hours) for the wick to absorb the kerosene.

Jan 31, 2011 | Dyna-Glo RMC-8001SS Heater

1 Answer

Burning correctly


since the unit is new I would contact customer support at the we site or by calling phone number in owners manual.

Jan 15, 2010 | Northern Tool 10,600 BTU Radiant Kerosene...

1 Answer

Kerosene heater


Dyna Glo 95 c4 Manual
http://www.owneriq.com/mdownloads/8979e0af-dfee-45f1-a8ba-c05c2f5ed4a8.pdf

Jan 31, 2009 | Dyna-Glo RMC-8001SS Heater

1 Answer

I have a dyna-glo rmc-95-c6 heater it smokes and makes an awful smell  the flame is not as high as shown in the owners manual  what can i do to fix the problem?  thanks


You can buy the wick at Lowes. I have the same heater. They where $10.00 each so I bought 2. I will go back and stock up on them. Package Number DH-145 It will say it will fit RMC-95C thur RMC-95C7

Jan 24, 2009 | Heating & Cooling

1 Answer

I need to buy a replacement wick


You can get them at Lowes for less then $10.00 Number DH-145

Dec 23, 2008 | Dyna-Glo RMC-8001SS Heater

1 Answer

Dyna Glo model 95 C2 wick replacement is a boogar even with so called instructions is there any trick to this wick is hard to hold in place and insert over round housing without pulling out 3 sidepins have...


turn the wick control knob all the way up before installing new wick. Put it all back together and make sure wick goes all the way down inside the groove when you push the shutoff lever. Do this several times. If not, then heater WILL NOT shut off !! P.S..use clear K-1 kerosene....the K-1 with red color seems to make bad carbon deposits on the wick...in a short time the wick becomes crusted and will not drop down to extinguish the flame. I had to open it up and put baking soda on the wick to put it out.

Dec 16, 2008 | Dyna-Glo RMC-8001SS Heater

2 Answers

Changing Wick in Kerosene Heater


http://www.ghpgroupinc.com/heaters/manuals.aspx

Here is the complany website..parent group name is GHP group..crazy they don't link DynaGlow more easily in a web search

Nov 08, 2008 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2519 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...