Question about Wurlitzer Jukebox CD Player

3 Answers

I have a nsm hyperbeam laser disc it played all last night switched it on this morning and it wont play it just says err 31 any help please?

Posted by on

  • phil Mar 24, 2014

    take the battery out, turn it round and put it back in, switch on the juke for a couple of seconds and then back off. Turn the battery the right way round again and you should be able to get into the programming. Unfortunately this does clear the memory so you will have to re-program the juke but try these 2 bits of programming to get you working again. Pull the service switch and you will get P and some numbers, press the C button till only the P remains, Enter 60 then H then 16 and H Next Press C till only the P remains Enter 70 then H then 25 and H Put service switch back nad use the credit button near the coin mech to clock credits and you should be able to play something.

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Wurlitzer Expert
  • 567 Answers

Error 31= memory contents invalid or not programmed you need to reprogramme

Posted on Dec 17, 2011

  • scott Armstrong
    scott Armstrong May 01, 2012

    how do you reprogramme a hyperbeam lazer disc ?

  • phil Apr 16, 2014

    you need the manual

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Did you figure out what it was i have the same problem

Posted on Nov 09, 2011

  • phil Apr 16, 2014

    error 31-memory try reprogramming if that fails its the memory battery at fault

  • Phyllis Gardner
    Phyllis Gardner Apr 24, 2014

    where you get a manual? model # 3310382

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Did you try opening the door and then pull out the door button. After which press the "c" key until the error goes away and see what happens.

Posted on Mar 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a nsm hyperbeam and can't get it to play


Maybe the battery timer chip is faulty so the machine needs programming. Look for them on Ebay, Keith Bad sells them and will advise you.

Sep 25, 2014 | Audio Players & Recorders

1 Answer

Says my mw2 disc is unreadable, it was working just last night and even played games this morning


if you have a ps3, i can't help you. If its a 360, then the console may have recieved some kind of shock while playing, and circle scratched your disc. Its either that or a fairly common hardware failure. Call 18004myxbox. microsoft tech support should help you out.

Jan 31, 2011 | Video Game Consoles & Games

2 Answers

I have a hyperbeam laser disc jukebox,and it was on free play when i bought it years ago.it's no longer on freeplay and i dont remember how to do it.any help would be great


camino69 my juke box has a black switch on the upper right side by the coin receiver. it looks operates like a car door lock. If yours is in this approximate location try switching it to the oposite position.

Oct 27, 2009 | Audio Players & Recorders

3 Answers

NSM Hyperbeam Wall mount Juke box


if you get error 61 it means check cd and exchange,or cd changer or at the most it could be the decoder board you could try jukeboxworld good site for manuals etc

Jun 03, 2009 | Wurlitzer Jukebox CD Player

2 Answers

How to put it on free play


One way to do it is press the button inside the machine situated on the small circuit board where the coins enter but that doesn't give you unlimited credit.

If I'm right in thinking that the Hyperbeam is ES 5.1 technology following these steps should solve it for you.

When you open the front, up by the small strip light at the top is the maintenance/service switch. Pull it out and the display will change to P ##.

Press C on the selection pad.

Then press 090 H 0 H to cancel any active time windows that might already be set.

Then press 094 H 200 H. When you have finished push the maintenance button back in and the credits should show as 99 and should stay at 99 even when a selection is made.

If you have a remote control with a credit button you should be able to switch between free credit and paid for credits but pressing this button.

Feb 18, 2009 | Juniper Networks IDP Upgrade Kit for ISG...

1 Answer

PS3 wont play disc's


If you have problem with loading your disk or some kind of media a most common error is Disk Read Error,or in a short way DRE.
Ps3 Laser is a very precise mechanism and optic and also a well none proble for the all machine right now on the Market.
Sony had the same problem before with PS2 and tried to fix the same issue all ready but without any luck at all.Actually i do believe is Part of the Market Strategy making the laser not to strong so people can buy new laser and keep the techical support alive.Most common error on Ps3 is DRE and some other like power supply Failure or Hd defective.
What is sad actually the fact the laser is Collapsing onthe spot.
On the ps2 you have some time to realize the laser is bad since the machine start not reading well or freezing during the game.On ps3 the laser stop working and that`s it.
I suggest to replace laser or try to clean first because sometimes if you are lucky the laser start working again

Jun 17, 2008 | Sony Playstation 3 (PS3) Console

2 Answers

Err disc


The laser eye is tired(out of alignment) from playing alot of burned disc. Have some one who know re-align it. Goodluck.

Mar 07, 2008 | Dual XDVD8180 Car Video Player

5 Answers

Jukebox error


error 61 on the nsm is a cd read error nothing to do with the amp, clean laser lens with a cotton bud and spit not spirits etc just saliva, then make a blank selection and see if the laser emits red beam, if not then the laser is faulty, check connections etc, if it picks up the disc but does not spin it its the decoder at fault, places like act marketing london, jukebox showroom, capital coin, herondata sales or anyone operator within the amusement industry will gladly sell you an exchange unit, or just try the coinslot industy magazine online or order via wh smiths

Mar 04, 2008 | Audio Players & Recorders

Not finding what you are looking for?

Open Questions:

See all Wurlitzer Jukebox CD Player Questions

Wurlitzer Jukebox CD Player Logo

Related Topics:

966 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wurlitzer Audio Players & Recorders Experts

phil

Level 2 Expert

567 Answers

Donald Chadwick
Donald Chadwick

Level 1 Expert

5 Answers

The Knight
The Knight

Level 3 Expert

73647 Answers

Are you a Wurlitzer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...