Question about HP Color LaserJet 2600n Printer

4 Answers

Jam in output bin

I printed a 65 pg doc, and it piled up in the output bin, jamming 2 pages: one outside in the output bin and one inside feeding into the output bin. I carefully removed both. Following instructions, I reset the Select button as instructed, but I keep on getting the message: "Jam in output bin."

I powered down. I reset the fuser lever inside. I took out the cartridges to see if anything was jammed behind them. I can't finsd any paper jammed any place, and can't get rid of the error message. I tried to print a test copy, and the printer send an error message to my laptop.
I followed all instructions on te HP Tech Support page---with no luck.

HP no longer supports this printer as it's just over tha warranty. Their suggestion was to turn it in and buy another. Grrrr!

Posted by on

  • 1 more comment 
  • dmckinney1 Jul 10, 2008

    Similiar problem: tried to print labels, and the label sheet wrapped around the fuser. Dismantled the fuser and removed labels, and now I still get the "jam in output bin" (- also there's a 41.3000 in the error log.) AND to top it all off, the color registration is out of kilter. Almost ready to go back to my old trusty QMS printer... Did I get a sensor out of place, or ??? Any help would be greatly appreciated.

  • Anonymous Aug 26, 2008

    I have the same problem, Called HP and they where no help... is there a solutation to this? Thank you

  • Anonymous Mar 17, 2014

    Each time i open and close cartridge door to resume printing for each page in many.

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Make absolutely sure there actually is no paper jammed in there. 
I came to this page with the same warning, convinced I had a software glitch. Turned out there was a page accordion-folded down to the size of a pencil lead. I didn't know paper could be folded that small. 
Of course, everyone here may be a lot brighter than I am, in which case sorry to waste your time. But for me, the obvious first fix needed to be thoroughly explored before cursing HP and their machine.

Posted on Sep 03, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Dear All

Actuly This Problem related with the formetter Board,
If you Have Any Other Scrap HP 2600 Printer You Just Change The Formetter Board.

Thank you

Posted on Feb 06, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 81 Answers

Maybe this will help. trace near output bin the actuator for for paper out. blow air on the sensor maybe there is an object that stack there.

Posted on Jul 21, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes - same problem here - though i'm guilty of cursing machine before finally realizing there was an accordian paper jam. To obtain better access at jam I removed top charcoal plastic cover (bendable snap out) and remaining lite gray top plate (four screws)

Posted on Sep 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gympac 1600 manual


Device error An internal error occurred in the device. Press (Select) to resume the job. - Door open The printer door is open. The door must be closed before printing can continue. - Engine comm. error The device experienced an internal communication error. This is a warning message only. Job output might be affected. - Invalid driver You are using the incorrect printer driver. Reselect the printer driver appropriate for your device. - Invalid entry Invalid data or response. Correct the entry. - Jam in Cartridge area A paper jam has occurred in the print path. Open the door and clear the jam. Then press the (Select) button on the control panel - Jam in Output bin A paper jam has occurred in the output area. Clear the jam, and then press the (Select) button on the control panel. - Jam in print paper path. A paper jam has occurred in the print path. Open the door and clear the jam. Then press the (Select) button on the control panel. - Jam in tray 2 A paper jam has occurred in Tray 2. Clear the jam, and then press the (Select) button on the control panel. - Jam in tray 3 A paper jam has occurred in Tray 3. Clear the jam, and then press the (Select) button on the control panel - Load paper The HP Color LaserJet 1600 printer is out of paper. Please load specified paper type into the tray indicated. - Load Tray X [TYPE] [SIZE] The printer is processing job, but the tray indicated is empty. Please load specified paper type and size into the tray indicated. - Manual feed The printer is waiting for paper in the tray indicated Load the paper as indicated. - Memory is low The device memory has been almost completely filled. Allow the device to finish the job, or press (Select) to cancel the job. Break the job into smaller jobs that contain fewer pages. - Misprint The printed pages have been incorrectly placed on the paper. To continue, press the (Select) button on the control panel.

Dec 31, 2014 | Printers & Copiers

1 Answer

Jam in top 3015d


Sir/Madam

Occasionally, media becomes jammed during a print job. An error in the software program and a jam message on the printer control panel display indicate a media jam. To prevent a jam, see the following instructions:
  • Only print on media that meets HP specifications.
  • Only print on media that is not wrinkled, folded, or damaged.
  • Make sure that the printer is clean.
  • Make sure that the input trays are loaded properly and are not too full. See the start guide for more information about loading input trays.
When adding new media, always remove all of the media from the input tray and straighten the stack of new media. This helps prevent multiple sheets of media from feeding through the printer at one time, which reduces media jams

Clearing a media jam


CAUTION: Media jams might result in loose toner on the page. Use cold water to wash toner off of clothes, as hot water will permanently set the toner into fabric. To remove toner from hands, wash hands in cold water.
CAUTION: Do not use a sharp object, such as a pencil or scissors, to remove jammed media.
NOTE: When clearing jams, including jams in the output bin, always push the print-cartridge-door release to open the top cover, and remove the print cartridge. Keep the top cover open and the cartridge out until the jam has been cleared. Opening the top cover and removing the print cartridge relieves tension on the printer rollers, which makes removing jammed pages easier.


Push the print-cartridge-door release and open the top cover.
Figure 1: Pushing release and opening top cover

3f0c0681-aab8-41b1-8ccc-edbc8d10b083.gif

Grasp the handle of the print cartridge and remove it. Set it aside.
Figure 2: Removing print cartridge


1135f64a-e54d-412a-a38c-2d53092ee8b0.gif

CAUTION: To prevent damage to the print cartridge, do not expose it to light any longer than necessary. Place the print cartridge in a paper bag or other opaque container until it can be placed back in the printer.

With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the device.
Figure 3: Jammed media most visible


38cea87e-25d6-4cfb-86b2-bbc3d933d279.gif

When the jammed media is removed from this area, replace the print cartridge.
Figure 4: Replacing printer cartridge


47beeaaf-6bbe-4681-9d09-8b877270789e.gif
Press the supporting springs, and close the top cover.
Open the media input tray and remove any media from the tray.

359bf88b-3c84-4de1-861e-08b6fe39b01f.gif
Slide the media guides inward as far as they will go. Press and hold down the tabs inside the media input tray, and slide the media input tray out of the printer.
Figure 6: Removing media input tray


92329010-15d2-4a56-a894-eacfba561eac.gif

With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the device.
Replace the input tray into the device.
Figure 7: Replacing input tray


141b20dd-a71b-4e53-86c1-b5e589fa0d60.gif

After clearing the media jam, it may be necessary to shut down the printer, and then turn it on again.

NOTE: To add new media, remove all of the media from the input tray, straighten the stack of media after adding the new media, and then place the stack in the tray.
Clearing other media jams
CAUTION: Do not use a sharp object, such as a pencil or scissors, to remove jammed media.
If the media has jammed where it exits the printer, grasp the leading edge of the media and pull the media out through the output bin.
Figure 8: Removing jammed media from output bin


b9b1737a-16cc-4bd2-b9a7-77bad78ef641.gif

NOTE: If the printer is shut off before clearing the media jam, turn it on again, and then restart the printing or copying job.
Tips to avoid media jams
Make sure the automatic document feeder (ADF) media lever is in the correct position for the media being used. Slide it to the single-sheet setting (to the right) when scanning on thick media. Slide it to the multiple-sheet setting (to the left) when scanning on regular media.
Make sure that the input tray is not overfilled. The input tray capacity varies depending on the type of print media that is used.
Check that the input tray is securely in place.
Do not add print media into the input tray while the printer is printing.
Use only HP-recommended media types.
Do not let print media stack up in the output bin. The print media type and the amount of toner used affect the output bin capacity.
Check the power connection. Make sure that the power cord is firmly connected to both the device and the power supply box. Plug the power cord into a grounded AC power outlet.
Media jams occur in the automatic document feeder (ADF)

Occasionally, media becomes jammed during a copy, scan, or fax job.

A software error message indicates a media jam, and the Doc feeder jam Clear, Reload message appears on the printer control panel display to indicate a jam.
  • The ADF input tray is loaded incorrectly or is too full.
  • The media does not meet HP specifications.
Typical automatic document feeder (ADF) jam locations Input tray areas: If the page is sticking out of the input tray, try to remove it gently from the input tray without tearing the page.
Figure 9: Removing jammed media from input tray


ec9c59d7-7daf-42c3-ba56-dc15042f3605.gif

Output paths: If the page is sticking out of the output bin, try to remove it gently without tearing the page.
Figure 10: Removing jammed media from output bin


e710c656-d551-4439-940d-878a82196f67.gif

  • Intermediate location: If the page is sticking out of the input tray and into the output area, see "To clear a media jam from the automatic document feeder (ADF)" below for instructions.

Automatic document feeder (ADF) media lever If a thick media is being used, slide the media lever to the single-sheet setting (to the right). Load a single sheet of media into the ADF.
When the copying, scanning, or faxing jobs are complete, slide the ADF media lever back to the multiple-sheet setting (to the left).
Clearing a media jam from the automatic document feeder (ADF)
  1. Using both hands, pull the printer control panel door toward you.
    Figure 11: Opening printer control panel door.
c5ce49eb-752a-4d44-bf67-99b4b9a44cc5.gif

  1. Remove any jammed media. Figure 12: Removing media
0cf6dfd4-a8b2-4153-8e19-52b3105abfda.gif

NOTE: Use only your hands to remove jammed media. Using other objects can damage internal parts.
Make sure that all of the pieces of media are removed, and then close the printer control panel door.
Figure 13: Closing printer control panel door


375c734d-e4be-4fed-b8ec-47628408dd9f.gif

I Hope Your HP Printer Problem Resolved By Now,In Case You still Having HP Printer Problem Then Visit Official HP Printer Website Below Link URL:

HP Printer Issue:
HP Support document HP Support Center

Or

If You still need HP Printer assistance Then Follow Us On :


HP Printer Support

Feb 13, 2014 | HP LaserJet Enterprise P3015d BW laser...

1 Answer

LOCATION OF PRINTER SENSOR


Jams

Clearing jams

CAUTION Do not use sharp objects, such as tweezers or needle nose pliers, to remove jams.
Damage caused by sharp objects will not be covered by the warranty.

CAUTION Always pull jammed media in the direction it would travel through the paper path.
Do not pull jammed media against the direction of travel through the paper path to avoid damage
to the printer.

To prevent damage to the printer when clearing jams, including jams in the output bin, always open the
print-cartridge door and remove the print cartridge. Keep the door open and the cartridge out until the
jam has been cleared. Opening the print-cartridge door and removing the print cartridge relieves tension
on the printer rollers, which prevents damage to the printer and makes the removal of jammed pages
easier.

Occasionally, media becomes jammed during a print job. You are notified of a media jam by an error
from the software and the printer control panel lights. See Control-panel lights (HP LaserJet 1010 series
printers) on page 102 or Control-panel lights (HP LaserJet 1020 printer) on page 106.

The following are some of the causes of media jams:

?

The input trays are loaded improperly or are too full. See Loading media on page 25.

NOTE When you add new media, always remove all of the media from the input tray and
straighten the stack of new media. This helps prevent multiple sheets of media from feeding
through the printer at one time, reducing media jams.

The media does not meet HP specifications. See Media specifications on page 21.

?

Typical media jam locations

?

?

?

Print cartridge area: See Removing a jammed page on page 43.

Input tray area: If the page is still sticking out of the input tray, gently try to remove it from the input
tray without tearing the page. If you feel resistance, see Removing a jammed page on page 43.

Output path: If the page is sticking out of the output bin, see Removing a jammed page


NOTE There might be loose toner in the printer after a media jam. This toner clears up after
a few sheets are printed.

Removing a jammed page

Use the procedures in this section to remove a jam.

CAUTION Media jams might result in loose toner on the page. If you get any toner on your
clothes, wash them in cold water. Hot water will permanently set the toner into the fabric.


Partshere Troubleshooting

CAUTION To prevent damage to the printer when clearing jams, including jams in the output
bin, always open the print cartridge door and remove the print cartridge.

To prevent damage to the print cartridge, minimize its exposure to direct light. Cover the print
cartridge with a sheet of paper.

NOTE The following illustrations show the HP LaserJet 1020 printer. The same procedure is
used to remove a jam in the HP LaserJet 1010 series printers.

1

Open the print cartridge door, and remove the print cartridge.

2

Grasp the middle edge of the side of the media that is most visible, and carefully pull it free from
the printer.

CAUTION Do not use sharp objects, such as tweezers or needle nose pliers, to remove
jams. Damage caused by sharp objects will not be covered by the warranty.

CAUTION Always pull jammed media in the direction it would travel through the paper path.
Do not forcefully pull jammed media against the direction of travel through the paper path to
avoid damage to the printer.


3

When you have removed the jammed media, replace the print cartridge, and close the print cartridge
door.

After clearing a media jam, you might need to turn the printer off then on again.

NOTE When you add new media, remove all of the media from the input tray and straighten
the stack of new media.

Sep 25, 2011 | HP LaserJet 1020 Printer

1 Answer

Paper feeds about half way and then stops. All of the indicator lights come on.


If you get a paper jam, the Paper Jam indicator light promptsyou to clear the paper path. If the paper has just started to feed from thepaper feeder when the jam occurs, pull the paper straight up out of the paper feeder. Open and close the printer cover toresume printing. If the paper jam occurs inside the printer, remove the paper from the output bin. Turn the printeroff, then on. If this doesn't clear the jam, open the printer cover.Remove the print cartridge and cover it.For additional assistance, please contactLexmark Technical Support

Apr 11, 2011 | Lexmark Optra E312L Laser Printer

1 Answer

Jam in Output Bin Message


The output Bin message comes from the sensor that reads when there are to many pages printed and they are sitting on the top BIN. Check the BIN sensor or arm and make sure that it is reading. Most of the time the sensor has a broken arm the the sensor reads to let it know when the BIN is full. You might want make sure that you reconnected the sensor and you have take the top cover off to replace the fuser.
Bruce

Jul 08, 2009 | HP Color LaserJet 2600n Printer

1 Answer

HP LJ P3005 13.31.00 ERROR


Hi,
As i can understand whenever you try to print with rear door closed printed page should come on top from top output roller however paper gets jammed.
Solution:
Try to print a page using rear door open and it should come out from the rear drop down tray it printed page comes out successfully with rear flap open than paper gets jammed at top due to faulty top output roller.
However if the paper gets jammed at fuser with rear door closed than it is issue with fuser in that case you need to get fuser replaced at the same time replace 20 tooth gear next to fuser.

Thanks and Regards
Neeraj Sharma

Apr 11, 2009 | HP LaserJet P3005n Printer

1 Answer

Jamming on Output bin...


Ok if the paper is half way coming out, Two things could be happening.
1.) Either your paper feed tires are Slipping and haven't reached the outpit bin sensor in time.
2.) second problem could be is that the fuser film is worn and is not fuser correctly and needs to be replaced.

Are you getting an Error Codes ???

Mar 06, 2009 | HP Color LaserJet 2600n Printer

1 Answer

Hp psc 1315 paper jam


Hi,



. Switch off the printer and disconnect the power supply. Allow any residual charge inside the all-in-one printer to dissipate before putting your hands or any metal tools inside the chassis.

2.
Pin down the exact location of the jam. The 3 hot spots for a jam are before a sheet completely leaves the paper tray, anywhere between the feed tray and print carriage or between the print carriage and output tray.

3.
Take off the front paper tray if the sheet jammed while still in the front area of the printer. If here, you should be able to see most of the paper.

4.
Pull the sheet with both hands and steady pressure. Do not tug as you might rip the paper, leaving a piece deeper inside the machine.

5.
Open the back panel to reach paper jammed between the feed-tray area and print carriage. Carefully remove the jammed paper.

6.
Use the carriage access door to get at a jam further inside the printer. You may need to remove the print carriage to get to the jam.

7.
Replace all parts and return any access panels to their closed and locked positions. Plug your printer back in and flip the power switch.

Jun 18, 2008 | HP PSC 1315 All-In-One InkJet Printer

4 Answers

Paper Jam Problem in Canon LBP 2900


I have a same problem .... somebody help us. :(

May 23, 2008 | Canon LASER SHOT LBP-2900 Printer

3 Answers

Paper jam light is on


Hi! I have the same issue. The only solution I still use: select print from document with no paper in the hp's feeder. Let the printer go on "paper out" message, now put the paper into the feeder and press the print button on the printer. Success!

Oct 05, 2007 | HP Photosmart 7450 InkJet Printer

Not finding what you are looking for?
HP Color LaserJet 2600n Printer Logo

2,012 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96627 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...