Question about AEG L66600 Front Load Washer

1 Answer

Please, I want to Know, how ti change the rubber door seal? thank you.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • AEG Master
  • 3,051 Answers

Hello there
Disconnect all power to the machine first!!
1 Locate the outer clamp band securing the seal to the door rim on the washing machine and examine it carefully for holes or tears. Many can be prised off with a flat-bladed screwdriver they have a spring system holding them, but some have a tensioning arrangement that has to be loosened.
2 After removing the outer clamp band, locate the inner one securing the seal to the drum and establish how this is secured. It may be necessary to loosen a clip, or you may be able to prise the band off with a flat-bladed screwdriver. Some are like very large Jubilee clips that you have to undo usually from the top.
3 Once the clamp bands have been removed, use both hands to pull the seal away from the inner drum rim. Some AEG machines have a water spout holes that will have to be lined up. Others have a drain holes.
4 Rubbing a drop of washing up liquid into the groove on the AEG door seal/gasket that locates on the drum makes fitting the new seal easier.
5 Your new AEG washing machine door seal should be fitted by locating the drain holes at the bottom of the seal first then push it on with both hands working opposite directions towards the top. This is quite hard if you have never done it before.
6 Refit the inner band remembering this must be tensioned correctly for it to be water tight.
7 now fit the outer band and the test your AEG machine for any leaks,

I

Posted on Jan 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I CANT GET FRONT OFF HOTPOINT AQURIUS TI CHANGE RUBBER SEAL


to change the door seal you have to take the front boot ring off fold the door boot into the drum and undo the retaining clip around the door seals inner drum you can get a screwdriver in from the top a bit tricky but its the only way as the front is riveted on and wont come off like the older machines

Dec 08, 2011 | Hotpoint Aquarius WMA56 Front Load Washer

1 Answer

Model wm0642hw front load. it leaks by door frame.rubber seal with clamp.only 2 years old. do i need to change the door frame outer part a151? thanks for your response in advance


Hi, If the door isnt loose or broken? Its more likely to be the rubber door seal if its leaking between the seal and the door glass. Check the edge of the seal where it touches against the glass for damage or ware if its ok clean any soap residue or bits from the glass.If it still leaks change the door seal.
Regards Elect App

Jul 13, 2011 | LG WM-2277HW Front Load Washer

1 Answer

Leak in rear lifthatch water leaking into rear storage area. It appears to be getting in under the rubber gasket door seal


Hi this is quite a common problem, you have a couple of options you can either go out and buy a new door rubber seal or if it one of those seals where you can get you hand in between two parts of the seal then what you can do is get some thick string and run this in the middle of the seal doing this will pack the seal out a bit and then when the door is shut this will make a lot better seal and it will then stop the water getting in.

let me know if you need further assistance ok

ps the rubber seal isnt to expensive to buy but even a new rubber may still have the same problem as its more to do with the way the door is fitted and it seems it dont push the seal hard enough to prevent water getting in so i have found packing it out with some thick string or twine will push the seal out more and will seal it properly when you shut the door to

plz rate this solution as i have a whole page of unrated posts, thanks

Aug 31, 2010 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Door not sealing properly. Visible gap in the upper left corner. Notice ice building up near gap. How do I fix it?


dear sir,
i think your freezer,s door there is one rubber between door and body it has been turn and damaged its need to replace. after change this rubber your who is sealing your freezer,s door your ice problem will be solve.

hope answer the question

thank you

please vote!

Jul 08, 2010 | Kenmore 13.7 cu. ft. / 388 liter Upright...

2 Answers

The rubber seal came off of the inside during the spin cycle - behind door against the tub -- and a wire ring came out. I put the rubber seal back on but have no idea where the wire ring would go? Is this...


The wire ring is the seal retaining spring, it fits in a groove at the rear of the door seal.
Double the seal back in the drum, and fit the spring around the seal at the rear of same, it fits inside a groove, it is difficult, so persist and be patient.
Please rate my solution.
Thanks.

Nov 03, 2009 | Bosch WFMC 3200 Front Load Washer

2 Answers

DI 'My self' Washing Machine Door Rubber



This video will show you how to change the door seal gasket on your neff washing machine Neff W5340X0
Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 14, 2009 | Neff W5340X0 Washer

1 Answer

MY DISHWAHER WHEN IN CYCLE HAS WATER LEAKING FRON THE FRONT DOOR.


there is some damaga in the rubber sealing please see that and change that front door rubber sealing then you ll find water not leaking after that.........

Sep 11, 2008 | Whirlpool Dishwashers

1 Answer

Rubber door seal


Try here: http://www.searspartsdirect.com

Jul 12, 2008 | Hoover HDV7FM Electric Dryer

1 Answer

Kenmore - 43142 front load - leaking


Which hose are we talking about? If you're talking about the small rubber hose at the top center of the door seal, HOW is it leaking? Is there a hole in the hose? Is the door seal itself damaged? Let me know a little more so I can give you the proper advice.

Jul 07, 2007 | Kenmore 43142 Front Load Washer

Not finding what you are looking for?
AEG L66600 Front Load Washer Logo

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...