Question about Whirlpool WFW8300SW

1 Answer

It says 24 F- and blinks the same thing over and over

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Whirlpool Master
  • 9,472 Answers

F24 Error
WATER TEMPERATURE SENSOR ERROR
If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle.

1. Unplug washer or disconnect power.
2. Check the water temperature sensor and connection to it.
3. Check resistance of heating element, if present on this model. (abnormal = infinity)

Posted on Jan 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clean llight blinks, owner manual said to replace


Hi,

The clean light blinking is due to a fault in heating the water, it could be several other things than the heat element. Here is a link to some instructions on how to reset the control so you can use the dishwasher, it also has a list of things that could have caused the not heating situation. Let me know if you have questions.

Blinking Clean Light

Jun 14, 2010 | Kenmore 24 in. 16049 Built-in Dishwasher

1 Answer

Dishwasher won't start and the green 'clean light' is blinking


your computer has detected a problem , most likely with the water heating. its locked up. Try pushing the high tem wash buton and then the energy saver button , push them back and fourth a few times(some modles its 2 other buttons) This should actavate a service check cycle where all the lights go on. Let it do its thing, and cancle after a few mins. if it locks up again you need service.

Dec 01, 2009 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Dishwasher will not work


This usually means a couple of things there could be a heater problem, water valve , or pump problem.

Jan 11, 2009 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

ALL the lights are blinking! Help!


DEAR FRIEND,
ngfam1 here for you!
I am happy to be of assistance!

When the lights are flashing that means there is an electronic problem!
best to let service do it!!

For this problem you will need to use factory service!

Here is the service company I refer my appliance customers too!
A&E Factory Service
A Nation Wide Company. / Available 24 / 7 for arranging appointments! In the USA.
1(800) 905-9505

Good luck!
You will be fine now!

Thank You
Bless you,ngfam1
PS. PLEASE GIVE ME A GOOD RATING HERE ON FIXYA.COM BEFORE YOU SIGN OFF!

Aug 24, 2008 | Frigidaire 24 in. FDB1050REC Stainless...

1 Answer

Kv24fs120 dead set with two led blinks


Two-blinks of the "Diagnostic STANDBY/TIMER LED" indicates one of two things:

1) Horizontal Output (Q502) in shorted on the A-board.

or

2) IC702 is shorted (CB board)

Two-blinks of the diagnostic red LED is a " B+ Overcurrent" problem.
The red LED will blink 2-times, stay off for 3 seconds, then blink 2-times. The cycle repeats.

The circuit board is quite delicate. One should not attempt repairs (unless one has high quality vacuum desoldering equipment such as a PACE desoldering unit).

Feb 01, 2008 | Sony KV-24FV12 24" TV

1 Answer

Is my tv dead?


no not at all , may be lot or h.o. transitror ar circuit dry solder, if any problem led red indicator blinks continuesly.. please chek all h.o section...and smps...

Sep 28, 2007 | Sony FD Trinitron WEGA KV-24FS100 24" TV

1 Answer

Green clean light keeps blinking


HI, Same thing happened to me today and Sears more than willing to charge me 200.00 for a 1 year service agreement. I found the answer on askmehelpdesk.com and the answer is: To reset a Kenmore Ultra Wash elite series dishwasher (stuck on clean) simply push heated/dry then normal wash and do the same thing again. Panel will reset itself and it hopefully will run normally again. Mine did and I am rejoicing! Julie

Aug 24, 2007 | Kenmore 24 in. 16302 Built-in Dishwasher

Not finding what you are looking for?
Whirlpool WFW8300SW Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2287 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...