Question about Computers & Internet

1 Answer

WHAT ARE THE JUMPER PIN CONNECTIONS FOR THE mAXTOR n256 HARD DRIVE

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 60 Answers

Try these illustrations. I'm not sure if this is an ATA or SATA drive (I couldn't find your model number) but this should point you in the right directions.
http://www.seagate.com/www/en-us/support/installation_assistance/jumper_setting_illustrations/

Hope this helps! : )

Posted on Jul 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need pin setting for N256 HD by Maxtor


Read the printed label gummed onto the top of the disk-drive, for the possible settings:
* MA(ster)
* SL(ave)
* C(able) S(elect)

Try the 'CS' position for the jumper, and connect the drive.

Feb 05, 2011 | Maxtor Hard Drive

1 Answer

Maxtor hd jumper settings n256 91366u4 primary


MAXTOR: no jumpers --> Master
one jumper --> Slave
two jumpers --> Cable Select

Dec 20, 2010 | Maxtor Hard Drive

2 Answers

Slave jumper settings for a Maxtor N256 Hard Drive


I have never personally seen one but most drives are the same for the type of jumpers installed. See if this helps you:

http://eshop.macsales.com/Tech/manuals/idehdsettings/Maxtor72.pdf

Apr 28, 2010 | Maxtor Hard Drive

1 Answer

I need the jumper settings for Maxtor N256 hard drive.


Hard drives have three jumper settings on them.
1.MASTER---MA
2.SLAVE---SL
3 CABLE SELECT----CS

If you have a hard drive on the end (last) on the ribbon cable connectors, then it is the master drive, and should be jumpered as such-- the jumper should be on the MA pins, any drive in the middle of the cable is jumpered as slave and should be on the SL pins.
CS usually causes problems, and I do not use it.
There are no jumpers on the motherboard that need to be changed for the hard drive. The only other settings for the hard drive are in the BIOS.
Please vote 4 thumbs up!!,
James.

Apr 23, 2010 | Maxtor Hard Drive

3 Answers

Jumper settings


25870e5.jpgCheck this diagram. it shows all configuration in detail..

good luck!!

Jan 02, 2010 | Maxtor Hard Drive

2 Answers

I need jumper settings for maxtor n256 model 96147h6 i wish to run it as a slave pls help. thx


For use as slave there is no jumper connected. (Master on/slave off0

Oct 04, 2009 | Maxtor Hard Drive

1 Answer

Jumper settings for a maxtor N256 master with slave


Select the maxtor HDD as master by setting the Jumper to the extreme left of the hdd; i.e. next to the data cable.
Remove all jumpers from the other HDD which you want to put as slave.

Sep 02, 2009 | Maxtor DiamondMax 80 (96147H6) 61.4 GB...

2 Answers

Jumper setting for maxtor n256 diamondmax vl 40 5400 rpm


There is usually a diagram on the drive showing the jumper configuration.

6b1bac9.jpg

Mar 16, 2009 | Maxtor Hard Drive

2 Answers

Jumper setting


The first jumper goes up and down on the two pins just beside the IDE cable slot and the other jumper goes across the top two pins next to it

Jan 23, 2009 | Maxtor Hard Drive

1 Answer

Hard drive was freezing up .i have already replaced and reloaded


On the back of the hdd you will see a row of little pins in groups of 2 vertically. It will be marked either right above the pins or on the top of the hdd above the pins, ma, sl, cs. The setting for slave is sl. Put the plastic jumper cap on those 2 pins & it is set for slave. Hope this helps & please remember to rate my answer. Thanks.

Jan 22, 2009 | Maxtor DiamondMax 60 (33073U4) 30.7 GB...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...