Question about Nintendo Wii Fit for Wii

1 Answer

When i turn on the wii fit, the blue light just blinks for a few seconds then goes blank. new batteries are in it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 112 Answers

I have never had a wii fit board, but have had a wii accessory. I do know that The board needs to be synced with the wii. In the front of the wii where the sd card slots are there is a tiny red button. Press this button for 2 or 3 seconds. Then right afterward take of take off the cover for the batteries. There should be a similar button like the tiny button in the back of the Battery compartment Press this button.(make sure batteries stay in) you must do this quickly so you might want to take off the cover and locate the button before you do all of this.

Please Rate.

Posted on Dec 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The wii fit game is telling me to push the power button on the balance board with my foot. It blinks blue and that's it. The batteries are fine. So what do I do?


You need to sync the balance board with the Wii. It's easy to do and takes 10 seconds.

1) Start Wii Fit.
2) When it asks you to push the power button as you're describing, open the SD card slot on the front of the Wii and observe the red button.
tkahill.gif

3) Now, flip over the balance board. Remove the battery cover on the bottom of it, and press the red button beside the batteries, and the blue light should start to blink.
tkahill_0.gif

4) While the blue light on the balance board is still blinking, quickly press the red button on the Wii. If they are both blinking at the same time, they should be syncing to each other.

5) Your Wii Fit Balance Board should now be synced with your Wii! If it has been synced successfully, you will no longer need to sync it, and should now automatically connect when the button is pressed with your foot.

Apr 09, 2011 | Nintendo Wii Fit for Wii

1 Answer

My wii fit board will not turn on it is new please help


Steps:
  • You need to make sure game is in first
  • push power than blue light will blink
  • after the light finishes blinking and still does not turn on then do sync procedure
  • open the battery side and push the red sync button then quickly push the sync button on the wii and wait for it to blink and light should be on

Mar 05, 2011 | Nintendo Intec Nintendo Wii Fit Action...

2 Answers

My wii fit balance board keeps blinking but will not stay on. batteries are good. cant find my instruction book. what could be my problem????


follow this
  1. Insert a Wii Balance Board compatible game disc in the Wii console.


  2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.

  3. Open the small SD Card slot cover on the front of the Wii console.

  4. Remove the Battery Cover on the bottom of the Wii Balance Board.

  5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.

  6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.

  7. The blue light will stop blinking and stay on steady once the syncronization is complete.

Jul 20, 2010 | Nintendo Video Game Consoles & Games

1 Answer

Our Wii Fit Plus will not recognize sensor to play. Light blinks for a few seconds then goes out. We tried replacing batteries.


You need to put in the Wii fit game and bypass all the screens until it is looking for play options.Take the battery cover off of the Wii board and open the large cover on the front of the Wii console.Press the sync button inside the battery compartment on the board,then press the red sync button at the top of the open console.If the blue light stays on constant,they are synched.If not,try again.Good luck and Game On!

Jun 23, 2010 | Nintendo Wii Fit Plus for Wii

2 Answers

I have a wii fit board, when you power it up, it


Had the same problem. It's a sync problem.
First, best to double check you have fresh batteries.
Next, turn the board upside down and remove the cover from the battery compartment.
Open the small hatch cover on the front of your console unit.
Now start wii fit from the disk menu item.
Next, press the small red button inside the balance board battery compartment. The blue lights will blink for approx 3=5 sec.
While they are blinking, press the red button on the console (in the hatch compartment).
This should re-sync your board and the light stays lit.
Good luck.

Apr 07, 2010 | Nintendo CTA Digital WI-BBP Wii Fit...

1 Answer

Wii fit board won't work


Hello,

Here you have different procedures on what to do if you get that error message. Please get back to me if nothing works.

The exact procedure is:

• Even if the battery level is strong, try the following:

Remove the batteries in the Wii Fit Board for at least 1 minute…… better 15

Try these steps!

1 Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.

2 Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

3 After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:

a With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

b Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

c Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).

d When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

4 Start the game from the Wii Menu, then sync the Wii Balance Board from the opening screen of the game.

Hope it helped.

Nov 24, 2009 | Nintendo Wii Fit - Balance Board + Game...

1 Answer

Synching wii fit causes wii console to no longer power up


1, Turn off and unplug your wii console for a few minutes
2,Turn the power back on and when you see the the safety screen open the small flap on the front of the wii console. Inside you will find the red sync button. Press and hold the red button down for 15 seconds.
* Then remove the battery cover from the wii remote, inside you will see another red button.
* Press and release the red button, the blue lights on the remote will start blinking.
* Quickly press and release the red sync button on the wii console.
* The remote will stop blinking and it should now be synced.
then try syncing your wii fit bored

Dec 28, 2008 | Nintendo Wii Console

2 Answers

Wii fit balance board


You need to sync the balance board with the console. Instructions are in the manual. Sync button for board is in battery compartment and sync button for console is in panel under reset button.

Took a few tries for me, be carefule not to hold sync button on console down for longer than 10 seconds because it will deregister all wii remotes.

Sep 09, 2008 | Nintendo Wii Console

3 Answers

Power


    Try these steps!

  1. Insert a Wii Balance Board compatible game disc in the Wii console.

  2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.

  3. Open the small SD Card slot cover on the front of the Wii console.
  4. Remove the Battery Cover on the bottom of the Wii Balance Board.
  5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.
  6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.
  7. The blue light will stop blinking and stay on steady once the syncronization is complete.

Sep 09, 2008 | Nintendo Wii Fit for Wii

1 Answer

Wii fit


Have had this problem before with wii sports. What I did was turn off the wii console and unplug from the power, leave for a few seconds then turn it back on when the health & safety screen comes up
  1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.


  2. Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

  3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:
  4. With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

  5. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

  6. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).

  7. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

Jun 23, 2008 | Nintendo Wii Console

Not finding what you are looking for?
Nintendo Wii Fit for Wii Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles & Games Experts

Bee Santiago

Level 2 Expert

268 Answers

Raj Patel

Level 3 Expert

899 Answers

phil

Level 2 Expert

567 Answers

Are you a Nintendo Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...