Question about Raymarine A50D GPS Receiver

1 Answer

My raymarine a50d frozen in the same page, i need to reset the unit, could you help me how to do it?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

To reset the A Series unit... power down the unit. Then PRESS AND HOLD the #1 Soft Key (left most button on below the display window) while you power up the unit. The unit display will come up quickly... then will go to a white screen that says " RESET IN 3...2...1...". Screen will then kick off. That is the MASTER RESET of the unit.

If you continue to see the unit lock up after that, if you have a seperate chart card that you use (Navonics), try running the unit with and without the card. You may find that the Chart Card is causing the unit to lock up. If not, you likely will have to send in the A50D for repair to NH.

Good Luck!! :)

Posted on Jan 25, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A50D


In general, you should be ablt to go to the settings page and one of the items will be units. Go to that page to change the units. Raymarine has an extensive on line set of usermanuals for more detail.

Jul 14, 2014 | Raymarine Boating

1 Answer

Raymarine a50d continuously resetting itself?


If there's a memory card installed for maps, try starting up the unit with it removed. It's possible that the card might be corrupted and stalling the start-up sequence.

May 10, 2014 | Raymarine A50D 5" Fishfinder /...

1 Answer

50d


this happened to my camera. i just restsarted it if you can do that.

Jul 07, 2013 | Raymarine A50D 5" Fishfinder Chartplotter...

1 Answer

Raymarine manuals for a50d


Gotcha covered!

The link below will give you access to your owner's manual for the A50D.

-Steve


Series A50 A50D A57D A70 A70D

Jan 29, 2012 | Raymarine A50D 5" Fishfinder Chartplotter...

1 Answer

A50D turns on OK but every few minutes it 'reboots' itself as if shutting off and turning back on?


Hello
The fault is due to some firmware bugs. Just reset the system. Go to page [143] of its user manual, and make system reset and settings & data reset. OK.

Dec 16, 2011 | Raymarine A50D GPS Receiver

1 Answer

I have changed my boat and have kept the ST2000 and S100 remote and the wireless base to fit on my new boat. Is it possible to get a wiring diagram to fit this to my new boat please


HI!

We have the same setup on our vessel.

Here's the link from Raymarine for instructions to install your base unit: http://www.raymarine.com/ProductDetail.aspx?SITE=1&SECTION=2&PAGE=1020&PRODUCT=3036

(Click on Base Station & Controller installation)

And here is the link to your owners manual for your ST2000+:
http://www.raymarine.com/ProductDetail.aspx?SITE=1&SECTION=2&PAGE=87&PRODUCT=19

(Click on 81130 6.pdf)

These contain all the wiring information you need to get it done!
Happy Boating!

Jan 24, 2011 | Raymarine ST2000 Plus Tiller Pilot A12005

1 Answer

Error code on my RC400 Raymarine GPS 0x4000091 and system is locked any ideas?


It would appear you need to perform a hardware reset.

6.2 Resetting the System
Three types of reset are available for the Chartplotter:
Power-On Reset: When you turn the display unit off, then on again,
the screen reverts to the chart display with all windows cleared.
Hardware Reset: This procedure enacts a power-on reset if the unit
has entered a lock-up condition.
To perform a hardware reset, press and hold the POWER key for 9
seconds.

Hope this helps.
Good Luck!

Apr 12, 2010 | Raymarine RC400 GPS Receiver

1 Answer

Display control unit frozen, display just reads standby


The reason is because the housingin is a little bit broken or throw the keypad water came inside yuor Display and after this the oxidation ha destroyed a part of the printid circuit or the switch of the keypad

Oct 03, 2009 | Raymarine Boating

1 Answer

Raymarine GPS system HALT ! URGENT PROBLEM


To get back up and running you are going to have to reset the unit. This is from the handbook:

Note: Take care - factory reset clears allWaypoint and Route databases.
➤ To perform a factory reset:
1. Power off the unit.
2. Press and hold CLEARwhilst powering up until <Erase backup procedure>
is displayed.
3. Either press CLEAR to abort Factory Reset and resume normal
Power-Up or press ENTER to continue Factory Reset.
4. Press ENTER again; the unit restarts as for a first time PowerUpwith
all values reset to their original factory settings

When you hit port and have an internet connection, make sure you are running the latest software version, currently listed online as version 1.09. You can download it here:

http://raymarine.custhelp.com/cgi-bin/raymarine.cfg/php/enduser/std_adp.php?p_faqid=965

Sep 10, 2007 | Raymarine Raychart 435 GPS Receiver

Not finding what you are looking for?
Raymarine A50D GPS Receiver Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Raymarine GPS Experts

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

The Knight
The Knight

Level 3 Expert

74136 Answers

Steve
Steve

Level 3 Expert

693 Answers

Are you a Raymarine GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...