Question about Kenwood (PDS36-20) Power Supply

1 Answer

Kenwood Power Supply Dip Switch Setting

We have a Kenwood Power Supply Model PS36-10. It was set previously to function remotely controlled. We want to set it to manual setting. It has a d swith with 10 sliders at the back. Please help us how adjust this dip switch. What should be the setting of each slider/dip switch to let it function manually?

We hope somebody could help us urgently. Thanks,

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Why don't you get a controller for that supply? I got one...

Posted on Aug 26, 2008


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Question about Dell D220P 01 Optiplex AC/DC Adapter 220-Watt Power Supply HOW DO I USE THIS UNIT TO PROVIDE 12V STANDALONE POWER?

most power supplies have a switch for 120 and or 220 options just move the switch to what setting you want. most power supplies can be used as a stand a lone power supply, if not than you need to request for a 220 watt power supply the can be used as a stand alone for pc or computer use. most computer retail should have them in stock. look on line or at

type power supplies stand-a-lone 220 watts computers compatible

Mar 02, 2015 | Dell D220P 01 Optiplex AC/DC Adapter...

1 Answer

How to get a symmetric DC power supply : i.e +18 Volts -18 Volts and ground from this kenwood power supply PDS36-20

You can't do that because it's not a split supply. There's just a single output referenced to ground, so all you can get is one voltage at whatever you select from 0 to 36 volts.

Aug 01, 2011 | Kenwood (PDS36-20) Power Supply

1 Answer

Which way for the unlabaled 115v setting?

the power supply will accept any voltage between 110 and 250 without the need for a switch, the red switch on the back is for the leds

Feb 25, 2011 | Kingwin Lazer LZ850 850W Modular 80 PLUS...

2 Answers

My old power supply had 4 wires going to the front panel on\off switch. The Dynex power supply does not support the switch. what do I use to turn the unit on or off. Will the unit function with out the...

Normally the front panel on/off power button and the front panel reset button plug into connector pins on your motherboard.

If you can find a User Manual for your motherboard it will show you exactly where the switch leads plug in on the motherboard. The motherboard's manufacturer and model number will be printed on the board somewhere.

Good luck.

Feb 05, 2011 | Dynex DX-400WPS 400-Watt Power Supply

2 Answers

How to power up a compaq 243890-001 power supply without the the motherboard? Its not green to ground

Remove Power Supply
1 . Shut down your computer and unplug the power cord and all cables connected to the system.

2 . Open the computer case and disconnect all power connectors from the motherboard, drives, cards and fans.

3 . Remove the four screws that secure the power supply to the case. These screws are located on the back of the computer case, at each corner of the power supply.

Wire and Start Power Supply
1 . Switch the power supply to the "Off" (sometimes "O") setting.

2 . Insert the end of one wire from a single pole, single throw (SPST) switch into the green wire of the ATX power connector (the largest power supply connector).

3 . Insert the end of the other wire from the SPST switch into the black wire of the ATX power connector. If your power supply has two black wires, connect the SPST to the black wire directly beside the green wire.

4 . Wrap electrical tape around the ATX power connector and wires from the SPST switch to hold them in place. Make sure there is no exposed copper or silver wire from the SPST switch wires.

5 . Turn the SPST switch to the "Off" position, if not already set. Plug the power supply into the wall outlet and switch it to the "On" (sometimes "I")setting.

6 . Connect any other computer components that you wish to operate without the motherboard, such as fans, drives or cards. Turn the SPST to the "On" setting to activate the power supply.

Hope the above information will be helpful to you.

Dec 01, 2010 | Compaq (243890-001) 250-Watt Power Supply

1 Answer

Under AC 110V condition, everything looks fine pretty well, but it is not worked completly under AC220V condition. What's problem??

I give 240 supply and set smps switch setting was 115, so transistor was blast, so trasistor no was erase, so plz send me trasistor no.

Nov 29, 2010 | Enhance Technology (ATX1140H) 400-Watt...

1 Answer

Replaced the dell 8400 power suppley, -now system says floppy disk failure (I don't have a floppy) CD R/W have power, but don't work? Is there a schematic available?

Hello my friend probably is a bios setting,somehow you hit default settings or flash your bios and you turned it on.Go into bios(hitting del on boot) and on the general page there will be a setting for a floppy drive, likely something like floppy 3.5" 1.4mb choose it and hit enter and you should be able to disable the floppy drive.If there is no setting, look for a HALT ON ALL ERRORS setting and change it to keyboard onl.

Feb 06, 2010 | Dell Dimension 8400 power supply ** FREE...

1 Answer

My philips televison doesnt turn on Previously I would just unplug it and plug it back on and would turn on I believe that its the on/off switch that isnt working properly. The TV works it just cant be...

You should at least try turning it on/off using a remote if you can't turn it on/off on the TV keyboard. Pulling the the plug on it and turning it on by plugging into the wall isn't a good thing to do, you will eventually burn something out in your power supply or elsewhere due to the harsh transient currents you are subjecting your electronic components to. Your power supply may have a relay in it that delays activationg some components until others are energized and you are bypassing all that with your method.

Sep 06, 2009 | System Power Supplies

1 Answer

I have customers overseas that have the EMACS HP2-6460P power supplies in their systems and they say that the systems do not shut down properly and they eventually unplug the power from the wall. What...


I would ask the customer a few questions:

1. Do you have the computer connected to a power adaptor or is it a voltage switching pc?

2. Has the pc always done this? If not, have you changed any power setting in the control panel? (Or have the checked the power setting.)

3. When was the last time the pc shut down properly? Maybe the pc is trying to install updates and need time to finish the install. (If when powering off the pc you see a shield over the power icon from the start menu, let the pc run its course and it should power on/off correctly.)

Good Luck

Aug 13, 2009 | HP2-6460P EMACS PS/2 460W Power Supply...

1 Answer

Need user manual for Kenwood power supply PD56-6D

I could not find it free(the manual) but if you want to buy one ($23) it is available here. Hope this helps.

Mar 25, 2009 | Kenwood (PD56-10AD) Power Supply

Not finding what you are looking for?
System Power Supplies Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood System Power Supplies Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers


Level 3 Expert

5660 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Are you a Kenwood System Power Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides